VEVOR B1Q01001 Kitchen Utility Cart User Manual
- June 2, 2024
- VEVOR
Table of Contents
VEVOR B1Q01001 Kitchen Utility Cart
IMPORTANT INFORMATION
We continue to be committed to provide you tools with competitive price. “Save
Half”, “Half Price” or any other similar expressions used by us only
represents an estimate of savings you might benefit from buying certain tools
with us compared to the major top brands and doses not necessarily mean to
cover all categories of tools offered by us.
You are kindly reminded to verify carefully when you are placing an order with
us if you are actually saving half in comparison with the top major brands.
This is the original instruction, please read all manual instructions
carefully before operating.
VEVOR reserves clear interpretation of our user manual. The appearance of the
product shall be subject to the product you received. Please forgive us that
we won’t inform you again if there is any technology or software updates on
our product.
Thank you using this product. In order to make sure that you can operate the machine correctly, read this instruction carefully before operation and keep it properly for future reference. Please be sure to read the precautions and safety rules in this page to ensure your safe use.
PRODUCT PARAMETERS
| Model NO. | Static load bearing | Dynamic load bearing |
|---|---|---|
| B1Q01001 | Max. 470 Pounds (About 213.2 Kg) | Max. 352.4 Pounds (About 160 Kg) |
CAUTION
- Place the weight evenly on the three layers of steel plate to achieve the maximum bearing capacity!
- Do not place all the weights on the same layer !
- The placement time under the maximum load bearing capacity shall not exceed 1 hour !
ASSEMBLY PRECAUTIONS
- Please assemble the product in strict accordance with the instructions. Incorrect assembly could be hazardous.
- Please wear safety goggles and work gloves properly during assembly.
- Do not try to assemble the product when feeling tired or when under the influence of alcohol, drugs or medication.
- Load bearing capacity and other product parameters are applied to the properly and completely assembled product only.
USE PRECAUTIONS
- This product is not a toy. Do not allow children to play with or get access to this item.
- Follow the intended uses only. Do not sit or stand on the cart.
- Check carefully before each use. Do not use if parts get loosened or damaged.
- Use on flat, level, and hard surfaces only.
- Do not exceed the listed load bearing capacity. Tighten all the knobs securely before placing weights on. Be aware of the dynamic load bearing capacity! Sudden load changes may temporarily cause excessive load, resulting in product failure.
PRODUCT PARAMETERS
For additional information regarding the parts listed below, please refer to the Assembly Diagram of this manual. Unwrap and separate all parts in a clear work area.
NO.
| A| B| C|
D
|
---|---|---|---|---|---
Name
| Panel frame| Pull the basket| Bottom net frame|
Whipple tree
|
Parts
| 
| 
| 
| 
|
Quantity
| 1PCS| 1PCS| 1PCS|
2PCS
|
NO.
| E| F| G| H|
I
Name
| Steel pipe| Plastic Clip| Pulley| Pulley (band brake)|
Screw & Nut
Parts
| 
| | | |
Quantity
| 4PCS| 24PCS| 2PCS| 2PCS|
2&2PCS
ASSEMBLY STEPS
STEP 1:
Install the plastic clip (F) on the lower clip slot of each steel pipe. Make
sure the arrow of all plastic clips(E) is pointed up, and the grooves of the
pole are covered by the convex line of the plastic clips.
STEP 2:
Install the steel pipe (E) on the four round holes of the net frame (C)
respectively, and ensure the same distance from the bottom of each steel pipe
to the bottom of the net frame, as shown in the figure below.
STEP 3:
Refer to Step 1, install plastic clips (F) at the height of 4 steel pipes(E)
and install horizontal bars (D) at the top of both steel pipes, as shown in
the figure below.
STEP 4:
Refer to Step 1 again, install the plastic clip (F) at the end and equal
height of the 4 steel pipes respectively; then install the panel frame (A) on
the steel pipe (E).
STEP 5:
Screw the pulley (G) and the pulley (with gate) (H) clockwise from the screw
hole at the bottom of the steel pipe (E), respectively.
STEP 6:
Position the basket (B) at the (D) card slot of the bar and push to complete
the installation.
STEP 7:
After the Pull the basket(B) is installed, install the screws and nuts(I) to
prevent the basket from coming out.
CUSTOMER SUPPORT
Manufacturer: Guangdong Shunde Heavybao Commercial Kitchenware Co.,Ltd
Address: No.3, Shatou Chung West Road, Jun’an Town, Shunde District,
Foshan City, Guangdong Province, China
EUREP UK LTD UNIT 2264, 100 OCK STREET, ABINGDON OXFORDSHIRE ENGLAND OX14 5DH
Importer: FREE MOOD LTD
Address: 2 Holywell Lane, London, England, EC2A 3ET
EUREP GmbH Unterlettenweg 1a, 85051 Ingolstadt, Germany
Importer: WAITCHX
Address: 250 bis boulevard Saint-Germain 75007 Paris
Support and E-Warranty Certificate https://www.vevor.com/support
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>