ARKSEN 005-PBK-FA2-SD Hitch Mounted Foldable Rack Handle Smart Tilting Owner’s Manual

ARKSEN 005-PBK-FA2-SD Hitch Mounted Foldable Rack Handle Smart Tilting

IMPORTANT INFORMATION

WARNING:

Manufacturer and seller expressly disclaim any and all liability for personal injury, property damage or loss, whether direct, indirect, or incidental, resulting from the incorrect attachment, improper use, inadequate maintenance, unapproved modification, or neglect of this product.

Thank you for purchasing our product.
This manual covers operation and maintenance information about the product. Read carefully and understand all instruction before using the product.
All information in this publication is based on the latest product information available at the time of approval for printing.
We reserve the right to make changes at any time without notice and without any obligation.

READ ALL INSTRUCTION BEFORE USE

WARNING! CAUTION!

• Inspect the product before use. Do not use if damaged or with missing parts.
• Do not use the product for anything other than intended use.
• Do not exceed the maximum load capacity of the hitch rating, vehicle load limit, or more than 2bikes.
• Always distribute the weight on the rack evenly.
• Ensure the rack and the load do not block taillight or any vehicle safety equipment.
• Always ensure the loads on the rack and check frequently.
• Make sure all pins are secured before use.

There are small components used in the construction of this product. Loose items should be kept away from pets and children to avoid a choking hazard.
Keep all plastic bags and packaging film away from pets and children to avoid suffocation.

SAVE THESE INSTRUCTIONS

SPECIFICATION

150 lbs
Fitting| Fit 2” steel hitch tube

ASSEMBLY INSTRUCTION

HARDWARE LIST

1. Folding Bracket
   1x

2. Connecting Bracket
   1x

3. Red Pin
   1x

4. Vertical Tube
   1x

5. Horizontal Tube
   2x

6. Short Hook
   1x

7. Long Hook
   1x

8. Wheel holders-L
   2x

9. Wheel holders-R
   2x

HARDWARE LIST

10. M1 0x55 Bolt x4
    10 Flat Washer x4
    M10 Lock Nut x4

11. M8x70 Bolt x6
    8 Spring Washer x6
    8 Flat Washer x6

12. Lock Knob x6

13. Triangle Pin x1

14. Screw x1

15. M10x60 Boltx1
    10 Flat Washerx2
    M10 Lock Nutx1
    

16. M12x80 Boltx1
    12 Flat Washerx2
    M12 Lock Nutx1

17. Clamping Coverx12

18. Tie Down Strap x1

19. Screw x2
    

20. Reflector Stickerx3

21. Keyx1
    

Required tools for assembly (Not included)

NOTE: The nuts supplied with the rack have nylon thread locker at the end of each nut. Once the threads of the bolt reach the thread locker, you will feel resistance as you tighten the nut and bolt. Continue to tighten until it is secured.

1. Insert the folding bracket(1) into the hitch receiver of the car, Then align the upper hole on receiver and insert the triangle pin (13), Use screw (14) to cover the pull rope of triangle pin (13) according to the Figure, and then tighten screw(14).
   

2. Tighten knob until there is no more play between the tongue and receiver.
   NOTE: Lock must be in unlocked position to tighten or loosen knob.
   
   The use of security locks

3. When the knob is tightened and folding bracket (1) is not shaken, insert the key and turn counter clock wise to enter the security anti-theft mode
   

   • Similarly, if you want to remove the bike rack from the car. Please insert the key and turn it clock wise, and then turn the knob anticlockwise with your hand until folding bracket (1) is loose, Remove triangle pin(13), you can remove the bike rack.
     

USER INSTRUCTION

1. Insert the connecting bracket (2) into folding bracket (1).
   Line up the hold with long bolt(16) and insert bolt through each hole. Threads the nuts onto the bolt and securely tighten.
   NOTE: Please pull the handle on connecting bracket(2) before you insert the bolt (16), then you can easy to make it connect the hole.
   

2. Insert the end of tubes (5) on both side of connecting bracket (2).
   Line up each holes on bracket (2) with bolts (10) and threads the nuts onto the bolt and securely tighten.
   

3. Insert bolts (19) connect with bottom side of connecting bracket (2).
   

4. Install the red pin (3) through the top hole in connecting bracket (2) and the tube (4).
   Use bolt (15) to cover the pull rope of red pin (3)according to the figure, and tighten the bolt securely using wrench.
   

ASSEMBLY INSTRUCTION

1. Install the covers (17) on the tube (5) and line up them with wheel holder (8,9) into the groove on the cover and tighten the knobs (12) of the wheel holders.
   

2. Install the covers (17) on the tube (4) and install bolts (11) through the holes with hooks (6,7) into the groove on the cover and tighten the knobs (12) of the hooks.
   

NOTE: Please remember to put lock washer and flat washer on it, then the knobs (12) can be tighten.

USER INSTRUCTION

LOADING THE BIKES

Adjust the wheel holder (8,9) in position, and put the bike on the rack.
Make sure the padded hooks (6,7) are pressing the bike frames, so that bikes are held tightly.
In the end, secure the bike wheel to the bike with the stabilizer straps.

ATTENTION!

• Safety strap is required at all time during transport.
• Make sure the knobs(12) on the hooks are locked after adjusting.
• Load the heavier bike closer to the vehicle. Make sure the total weight of the bike load is within the weight capacity of the rack or the vehicle. Overloading may result in damaging the product.

Put the bike on the rack and secure in plack with tie-down strap (18) to provide extra security.

LOWERING THE RACK FOR TAILGATE / BACK DOOR

Tilting Function: Pull up the handle/pedal button to easily tilted down when no carrying bikes.

Hold the rack firmly to avoid injuring yourself when pulling the handle or using the pedal to fold. The rack can be tilted away providing additional clearance for trunk or rear hitch access.

When using this feature, open the tailgate / back-door slowly and make sure there is enough clearance between the tailgate / back-door and the rack to prevent any damage on the vehicle.

NOTE: When using the pedal function to tilt the rack, push the rack forward or diagonally upward and then step down with foot, so that it can be easily tilted.

WARNING:

• It’s not recommended to tilt down the carrier when it carries bikes.
• Do not attempt to lower the rack when bikes are loaded on the rack.
• Heavy load. Two person lift recommended for smart tilt feature. Improper technique may case muscle strain or back injury.
• Only use smart tilting feature when parked.
• Always return the rack to the level position and ensure it’s locked into plack before transport.
• Do not allow the rack to fall freely into tilt position.

Fold up the rack

Fold Function: Pull up the handle to fold up when no carring bikes.

1. Remove the pin (3) and fold down the tube (4).
   NOTE: Insert the Red pin (3) into the other hole according to the Figure to fix the vertical tube (4).
   

2. Pull the handle to fold the rack up.
   NOTE: Please pull the handle on connecting bracket, fold up the rack.
   The buckle must be inserted into the upper slot.
   

ATTENTION! WARNING!

Failure to install the rack to the car receiver properly may result in the rack separating from the receiver and fall onto the road way, causing potential road hazard.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>