VEVOR 110201 Motorcycle Lift User Manual
- June 2, 2024
- VEVOR
Table of Contents
VEVOR 110201 Motorcycle Lift
Specifications
| Model | 110201 |
|---|---|
| Rated Capacity (LBS) | 1100 |
| Minimum Height (mm) | 95 |
| Maximum Height (mm) | 350 |
| G.W. (kg) | 13.7 |
Product Usage Instructions
Assembly and Setup
Read and understand the user manual before assembling and installing the motorcycle lift. Keep your hands and feet away from the working area at all times.
Using the Motorcycle Lift
- Use the screw design to adjust the height by rotating the screw manually. This lift is ideal for tire changing and maintenance on your motorcycle.
Operation:
-
1. Rotate the screw using a ratchet wrench to adjust the height of the platform. - Adjust the platform to the appropriate height and place the lift under the motorcycle, ensuring the load is aligned with the pivot point for stability.
- Lift the motorcycle to the desired height and insert the safety pin.
- Tighten the motorcycle with additional tools to secure it.
- After repairs, remove the safety pin, slowly rotate the ratchet wrench to lower the platform, and then remove the lift.
Warning and Maintenance
Always follow the safety precautions and guidelines provided in the user manual. Regularly inspect the lift for any signs of wear or damage.
FAQ
- Q : How do I adjust the height of the platform?
- A: Rotate the screw using a ratchet wrench to adjust the height accordingly.
- Q: What is the maximum weight capacity of this motorcycle lift?
- A: The rated capacity of this lift is 1100 LBS.
- Q: Where can I find technical support or warranty information?
- A : For technical support and an e-warranty certificate, visit www.vevor.com/support or contact CustomerService@vevor.com.
Use
Screw design, adjusting the height by rotating the screw manually, it is an ideal second lifting tool for tyre changing and maintenance on your motorcycle.
Operation
- Rotate the screw with a ratchet wrench to adjust the height of the platform.
- Adjust the platform to the appropriate height and place the lift on the bottom of the motorcycle. Make sure that the centre of the load aligns with the pivot, and keep the load stable and safe.
- When all this is done, lift the motorcycle to the proper height and insert the safety pin.
- Tighten the motorcycle with other tools to keep it stable.
- After repairing, pull out the safety pin, rotate the ratchet wrench slowly and gently to lower the platform until it departs from the pivot, and then take the lift away.
Warning and maintenance
- Read and understand the user manual before assembling, installing, operating, or servicing this product. Failure to follow these warnings and instructions can cause death, personal injury or damage to valuable property. And Keep the user manual.
- Do not overload the Engine Stand. Never exceed the maximum weight capacity of 1100 Lbs.
- The lift must be used on a solid and level surface, not allowing gradient and uneven surface.
- Keep the load stable and prevent the load from losing balance.
- Before using, lubricate the screw and the nuts with grease to make the lift flexible and antifriction.
- Keep children and unauthorized persons away from the work area.
- Wear ANSI-approved safety goggles when operating the lift.
- Only use this lift on a big, stable, level, dry and not slippery motorcycle lift platform. Keep the surface clean, tidy and free from unrelated materials and ensure that there is adequate lighting.
- Always keep your hands and feet away from the working area.
Specification
Model| Rated
capacity( LBS)
| Minimum
height(mm)
| Maximum
height(mm)
| ****
G.W.(kg)
---|---|---|---|---
110201| 1100| 95| 350| 13.7
DISASSEMBLE DRAWING
| Part No | Name | Qty | Part No | Name | Qty |
|---|---|---|---|---|---|
| 1 | Screw | 1 | 12 | Stand assembly | 1 |
| 2 | Screw coat | 1 | 13 | Hold ring | 8 |
| 3 | Pin 6×28 | 1 | 14 | Base | 1 |
| 4 | Ball Bearing8102 | 2 | 15 | Front Shaft | 1 |
| 5 | Washer | 1 | 16 | Restrict wrap 1 | 2 |
| 6 | Bolt | 2 | 17 | Bearing201 | 4 |
| 7 | Washer | 10 | 18 | Center Shaft | 1 |
| 8 | platform | 1 | 19 | Restrict wrap 2 | 2 |
| 9 | C-tube | 1 | 20 | Shaft | 1 |
| 10 | wrap | 1 | 21 | Rubber pad | 1 |
| 11 | Pin 6×18 | 1 | 22 | Safety Pin | 1 |
- EU Importer: WAITCHX， 250 bis boulevard Saint-Germain 75007 Paris
- UK Importer: FREE MOOD LTD, 2 Holywell Lane, London, England, EC2A 3ET
EUREP UK LTDb UNIT 2264, 100 OCK STREET, ABINGDON OXFORDSHIRE ENGLAND OX14 5DH
EUREP GmbH Unterlettenweg 1a, 85051 Ingolstadt, Germany
CONTACT
- Manufacturer: Zhejiang Jinhong Auto Accessory Co., Ltd.
- Address: No.36 Binhai Road, Jianshan, Haining, Zhejiang, China
- MADE IN CHINA
- Have product questions? Need technical support? Please feel free to contact us:
- CustomerService@vevor.com
- Technical Support and E-Warranty Certificate
- www.vevor.com/support
This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>