EASEHOLD BMD019 800W Powerful Juice Extractor and Maker User Manual

EASEHOLD BMD019 800W Powerful Juice Extractor and Maker User Manual

IMPORTANT SAFEGUARDS:

1. Do not let cord contact hot surface, including the stove.
2. This appliance incorporated a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug will fit in a polarized outlet only one way. If the plug can not fit fully into the socket, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way as this is a safety feature.
3. When using this electrical appliance, basic safety precautions should always be followed including the following:
a) Read all instructions before operating.
b) Do not put the motor housing in water or any other liquids to protect against risk of electrical shock.
c) Close supervision is necessary when the appliance is used by or near children.
d) Unplug from outlet when not in use, before addition or removal of any parts, and before cleaning.
e) Avoid contacting moving parts.
f) Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner. Please contact the seller to help solve the problem.
g) The use of attachments is not recommended as they can cause the fire, electric shocks or injury.
h) Do not use at outdoors.
i) Do not let cord hang over the edge of table or counter.
j) Do not let cord contact hot surface, including the stove.

SAVE THESE INSTRUCTIONS

Do not use the appliance if the rotating sieve is damaged.
If the supply cord is damaged, it must be replaced by the manufacturer, an authorized Service Agent or similarly qualified persons in order to avoid a hazard.

SAFETY INSTRUCTIONS:

1. Always make the sure juicer cover is clamped securely in place before the motor is turned on.
2. Do not unfasten the clamps while the juicer is in operation.
3. Be sure to turn the switch to OFF position after each use of your juicer. Make sure the motor stops completely before disassembling.
4. Do not put your fingers or other objects into the juicer opening while it is in operation. If food becomes lodged in opening, use food pusher or another piece of fruit or vegetable to push it down. When this method is not possible, turn the motor off and disassemble the juicer to remove the remaining food.
5. Do not use the appliance if the rotating sieve is damaged.
6. Unplug before cleaning and before assembling or removing parts.
7. Turn OFF before cleaning and before assembling or removing parts.
8. The cutting blade is extremely sharp so always use food pusher.

Technical Information

US: AC120V, 60HZ, 1000W
EU: AC220~240V, 50~60HZ, 1000W

Product Introduction

PARTS LIST:

1. Pusher
2. Funnel
3. Lid
4. Rotating sieve
5. Spout housing
6. Spout
7. Locking handle
8. Juice cup
9. Main body
10. Pulp Container
11. Power switch

SPECIAL HELPFUL HINTS FOR THE BEST PERFORMANCE

a) Do not put any fruit or vegetable in your juicer until power is turned on.
b) Remove large seed from fruits such as peach, mango, etc. as the seed will damage the blade of the unit.
c) The juicer has two speeds. II speed, high speed is for the hard fruits and vegetables like apples, carrots etc … and I speed, low speed is for soft fruits and vegetables such as watermelon, grapes and strawberries.
d) Do not use bananas or avocados as they do not contain juice and will clog JUICer.
e) Allow the juicer run for a few minutes before turning off to allow any excess juice to be extracted from the pulp. Wait until motor stop spinning before disassembling.
f) Do not immerse the whole machine into water or liquid at any time.

ASSEMBLY

Before first use. it is a good idea to yourself with the assembly/disassembly of the unit.

1. The appliance should be unplugged from the mains before assembly or disassembly.
2. Place the pulp container under the nozzle on the left of the machine. Place the Juicer Cup under the nozzle on the right of the machine.
3. Attach the Funnel Part onto the main body and clip the Filter and Blade into place.
4. Attach the Top Lid and close and place the Pusher in the food chute.
5. Make sure the housing unit is locked with the Handle in place by hooking them onto the top cover and pushing them downwards until they clip in place.
6. Make sure the Active juice outlet is put down before juicing.
7. The juicer will not work for safety reasons if the Handle are not locked in place correctly.

How to Assemble your juicer

Before assembling, remove all packaging and wash all parts except for the main body in warm, soapy water and dry thoroughly. Wipe the main body with a damp cloth. Do not plug into the mains power whilst assembling.

1. Align the pulp container with the lug at the bottom of the main body. Rest the pulp container up against the main body.

2. Place the spout housing onto the main body. Ensure the lip of the spout housing hooks over the pulp container as this holds the container in place.

3. Grip the sides of the rotating sieve and slot it onto the drive shaft on top of the main body. Once they are aligned, push down on the rotating sieve until it locks in place with a ‘clunk’.
   NOTE: You may need to rotate the sieve a little to align it with the drive shaft in the main body.

4. Align the lid with the top of the spout housing and pulp container assembly. Make sure the tabs on the lid align with the tabs on the spout housing.

5. Slot the plunger into the funnel in the top of the lid.

6. Slot the plunger into the funnel in the top of the lid. Your juicer is now ready to use.

How to use your juicer

1. Place the juicer unit on a f1at, level surface. Ensure the power switch is facing you and set to 0.

2. Put the plug into a nearby power socket and switch on.

3. Place the juice cup under the spout (1) and remove the plunger (2).

4. Prepare the fruit and vegetables.
NOTE: Always wash fruit and vegetables before juicing. Remove large seeds, pips or peel (if these are not removed they may damage and block the rotating sieve). Thick pith should also be removed for the best taste. Cut larger fruit and vegetables into smaller pieces so they can easily fit into the funnel.

5. Put a small amount of the fruit or vegetables into the funnel. Place the plunger back into the funnel and gently press down. Pressing down on the plunger too hard may reduce the amount of juice you get from your fruit or vegetables.

6. Turn the power switch to the desired power setting.
0: OFF setting
I: For soft and juicy fruits and vegetables
II: For harder fruits and vegetables Once the fruit or vegetables have been juiced, turn the power switch to the O setting. Remove the plunger and insert more fruit or vegetables and continue to juice until all of the fruit and vegetables have been used.
NOTE: Keep a close eye on the jug and pulp container as they will quickly fill up.

7. To empty the pulp container, ensure the power switch is set to ‘O’ and the power is off at the mains switch. Unlock the locking handles
(1) remove the lid
(2) and carefully lift away the pulp container
(3) Empty the container, preferably into your
Food waste bin or home composting bin.

Hints & Tips

1. Always replace the plunger before turning the juicer on to prevent Splashing.
2. If you’re juicing a lot of fruit or vegetables, you’ll need to clean the rotating sieve regularly so it doesn’t become blocked.
3. Always use fresh fruit and vegetables as these contain the largest amount of Juice.
4. Harder and more fibrous fruits and vegetables (e.g. banana, mango and avocado)are not suitable for juicing.
5. You can juice leafy vegetables (e.g. cabbage and spinach) by rolling the leaves up so they fit into the funnel.
6. The best fruits and vegetables to use are orange, grapefruit. lemon, lime, apple.melon, pineapple, tomato, cucumber and carrot.
7. For best taste, drink juice as soon as it’s made.
8. Fresh apple juice may turn brown when it comes into contact with air. Though this is perfectly natural, it can be reduced by adding in lemon Juice.
9. Pulp produced after juicing can be used in cake and muffin recipes.
10. Juice can be easily thinned down by adding sparkling or still water.
11. Never store the juicer when it’s dirty or wet.

How to clean your juicer

1. Ensure the juicer is switched off and is unplugged from the mains supply.
   Dismantle all the parts. Simply reverse the steps when you assembled the juicer as described in the ‘How to … assemble your juicer’ section of the manual. Take care when removing the rotating sieve as it has sharp blades.

2. Wipe the main body with a damp cloth and mild detergent if needed. Dry thoroughly. Never immerse in water.

3. Wash the rotating sieve, lid, pulp container, spout housing, plunger and juice cup in warm soapy water. These can also be placed in the dishwasher, though this may cause the finish to dull over time.

4. When washing the rotating sieve, take care as it has very sharp cutters at the bottom.

5. You may find it’s best to use a small brush (e.g. a nail brush) to clean the rotating sieve, to get all the food out of the cutting edges.

6. Please remember not to use harsh or abrasive cleaning agents, or scourers.

7. Ensure all items are dry and the motor housing is cool before storing in a clean. dry place, out of reach of children.

FAQ

Anke [Hong Kong) Network Technology Co., Limited
Address : 16/F Kowloon Building, 555 Nathan Road,
Mong Kok Kowloon, Hong Kong, 999077
Email : support@easehold.com
Website : easehold.com
Made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>