EASEHOLD Moon Mirror 70X100mm User Manual
- June 9, 2024
- EASEHOLD
Table of Contents
EASEHOLD Moon Mirror 70X100mm
FCC Compliance
This equipment has been tested and found to comply with the limits for a Class B digital devioe. pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or on experienced radio/TV technician for help.
EU Conformi1y statement
This product and – if applicable – the supplied accessories too are marked with “CE” and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU. the Ro HS Directive 2011/65/EU and Amendment (EU)2015/863. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated conection points. For more information. visit www.recyclethis.info.2013/56/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information, visit www.recyclethis.info.
Preventive and Cautionary Tips
Before operating your device, please read the below important notes
- Keep all liquids away from the device.
- Ensure environmental conditions meet factory specifications.
- Major shocks or jolts to the unit as a result of dropping it may cause damage to the sensitive electronics within the unit.
- Please use qualified power adapter with quality and safety certification.
- Improper use or replacement of the battery may result in hazard of explosion.
Product Description
Important Note
- Please do not disassemble the mirror without the tech support’s guidance.
- Please power off the mirror when you don’t use it for a long time. Never expose the mirror to direct sunlight Keep the mirror away from children.
- Do not place the mirror in any fire source which might lead to a fire hazard or even an explosion.
- Make sure your hands and the mirror are all clean & dry before operating the mirror since water or mist may influence the sensitivity of the mirror’s touch button.
Product Introduction
Note: The LEDs will be auto-off after using the mirror for 30 minutes.
Charging Status Description
Remove the mirror first and charge it.
How to Install the Mirror
- Screw-mounted inltallatlon: cement. whitewashed, wallpaper and other rough walls.
- Double … lded adheuft tape lnltallatlon: glass, ceramic, marble and other smooth walls.
Mount the Mirror with Screws
- Put the plastic base on the wall and mark the positions of the three holes.
- Use a drill with the 6 mm diameter to drill three holes based on the marking. The depth should be around 35 mm – 45 mm.
- Use a hammer to screw the plastic screw anchors.
- Mount the base to the wall with the screws.
- Put the wall mount on the base and rotate the tum-knob to fix the wall mount to the base.
- Stick the mirror to the magnetic wall mount and adjust the ideal angle.
- The ideal distance is :S 5.9 in when using this 7X magnifying mirror.
Mount the Mirror with Double-Sided Adhesive Tape
- Choose a smooth and clean wall. Make sure the wall is clean without water and smudge.
- Stick the 3M double-sided adhesive tape on the base and then stick the base to the wall. Press the base for 10 seconds to make it fixed to the wall.
- Rotate the turn-knob to the base after you have sticked the base to the wall for 2 hours.
How to Operate the Mirror
- Tap the power button to tum on/off the LED light; press and hold it to adjust the brightness
- Tap the light setting button to switch the light color (among cool white light warm white and natural light).
Specifications
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>