VADSBO CBU-A2D Casambi Compatible 2 Channel Instruction Manual

June 2, 2024
VADSBO

VADSBO CBU-A2D Casambi Compatible 2 Channel

VADSBO-CBU-A2D-Casambi-Compatible-2-Channel-product

Warning!
High voltage. Risk of electric shock. The installation should only be carried out by an authorised electrician. The CBU-A2D is a Casambi-compatible 2-channel 0-10V/DALI controller. CBU-A2D can control 1-10pcs DALI drivers (20mA output). The product has different functions depending on which profile it is set in, such as TW- (warm/cold white) and RGBW. CBU-A2D can control one or two 0-10V controlled LED drivers, or control one LED driver with tunable white
through two 0-10V control inputs. CBU-A2D can be controlled with the Casambi app which can be downloaded free of charge from the Apple App Store and Google Play Store. Different Casambi-enabled products can be used from a simple one- luminaire direct control to a fully featured light control system where up to 250 units form automatically an intelligent mesh network.

Technical data

VADSBO-CBU-A2D-Casambi-Compatible-2-Channel-fig-9

Dimensions

VADSBO-CBU-A2D-Casambi-Compatible-2-Channel-fig- \(1\)

Installation

Make sure that the mains voltage is switched off when making any connections. Use 0.5-1.5 mm2 solid or stranded conductor electrical wires. Strip the wire 6-7 mm from the end. Insert the wires into the corresponding holes and tighten the connector screws.

If the connected LED driver cannot be turned off completely from the control interface, an external relay with a 12 VDC coil can be connected to channel 2. Make sure the relay is protected against flyback voltage, e.g. do not use a PCB relay without the flyback diode. A suitable fixture configuration must be selected to control a relay. CBU-A2D, as any other Casambi product, should not be placed in a metal enclosure or next to large metal structures. Metal will effectively block
radio signals which are crucial to the operation of the product. A thorough connectivity testing is strongly recommended at the installation site.

Range
The range between two CBU-A2D units or between a CBU-A2D and a smartphone can vary a lot depending on obstacles and surrounding material. In the open air, the range between two CBU-A2Ds can be more than 200 ft, but if the unit is encapsulated into a metal structure, the range can be only a few feet. Therefore, thorough testing is highly suggested. Casambi uses mesh network technology so each CBU-A2D acts also as a repeater. When testing the network, it is important to test that each unit can be controlled from any point of the network-covered area.

Wiring diagram, Push Button

VADSBO-CBU-A2D-Casambi-Compatible-2-Channel-fig- \(3\)

Wiring diagram, 10 DALI drivers

VADSBO-CBU-A2D-Casambi-Compatible-2-Channel-fig- \(4\)

Wiring diagram, DALI sensor

VADSBO-CBU-A2D-Casambi-Compatible-2-Channel-fig- \(5\)

Wiring diagram, one driver and relay

VADSBO-CBU-A2D-Casambi-Compatible-2-Channel-fig- \(6\)

Wiring diagram, 2-channel LED driver

VADSBO-CBU-A2D-Casambi-Compatible-2-Channel-fig- \(7\)

Wiring diagram, two drivers (only 0-10V)

VADSBO-CBU-A2D-Casambi-Compatible-2-Channel-fig- \(8\)

Telefon/Phone: +46 (0)31-23 56 00
E-post/E-mail: info@vadsbo.net
order@vadsbo.net
Hemsida/Website/Facebook: www.vadsbo.net
facebook.com/Vadsbo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals