NEEWER X17 17 Inch Tablet Teleprompter Instruction Manual

June 16, 2024
NEEWER

NEEWER X17 17 Inch Tablet Teleprompter Instruction Manual


© 2021 Shenzhen Newer Technology Co., Ltd. All Rights Reserved.

This document is the sole property of Shenzhen Newer Technology Co., Ltd and shall not be, reproduced, transmitted, transcribed, stored in a retrieval system or translated in any form, by any means, without prior written permission from Shenzhen Newer Technology Co., Ltd. Shenzhen Newer Technology Co., Ltd reserves the right to change content in this instruction manual at any time and without prior notice.

Version Control

Date Version number Description Issued by
2022/06/15 V1.0 X17 Teleprompter Instruction Manual NEEWER 00

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC RF Radiation Exposure Statement:

  1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
  2. This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction

IC Warning Statement

“This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.” The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).

This radio transmitter has been approved by Industry Canada to operate with the antenna types listed with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction

About this product

NE ewer’s X17 teleprompter contains a high-definition display to present texts and a special coated glass positioned at a 45°angle in front of your camera to reflect the texts onto the display so that speakers can clearly read the script and look natural when facing the camera.

Package Contents

  • X17 Teleprompter ×1

  • Quick Release Plate Screw ×1

  • Remote Control ×1

  • Soft Cleaning Cloth ×1

Product Illustration

Product Illustration Product
Illustration

Product Illustration

Remote Control: Model RT-110

How to Install

  • Remove the protective layer of film
    Remove the teleprompter from its packaging and remove the protective layer of film on the glass before use.

  • Place the teleprompter on a tripod Insert the top screw of your tripod into the teleprompter’s bottom hole, ensuring a good fit, and tighten the tripod’s knob to secure (drop and lock system).

  • Adjust the angle of the beamsplitter

    Rotate the Beam Splitter Glass Lock counterclockwise, then adjust the glass to the required angle (recommended at 45°). Next rotate the Lock clockwise to hold in position,

  • Unfold the blackout shade

    Fully unfold the teleprompter’s blackout shade and zip it up on both sides. Please ensure the sides are fully sealed all around to avoid light leaking through.

  • Remove the quick release plate

    Pull out the Quick Release Plate Lock and slide the plate out of the base.

  • Installation of the quick release plate screw

    After removing the silicone plug from the quick release plate, install the quick release plate screw in the quick release plate slots, and then re-insert the silicone plug.

  • Attaching the entire quick release plate to your camera Insert the quick release plate screw into your camera’s bottom screw hole and tighten it.

  • Re-inserting the quick release plate back into the base

    Align the quick release plate with the slot of the base and and slide it in completely.

  • Placing tablet or cellphone devices to play texts

  •      Loosen the Tray Securing Knob by turning it counterclockwise, then pull the tray to extend and accomodate your tablet or cell phone. After inserting your tablet or phone used to play texts on the tray, push the tray a little bit inward to secure your device and finally rotate the Tray Securing Knob clockwise to tighten.

  • Adjusting the camera position

1. Rotate the Holding Base Lock to loosen. This will enable you to slide the Camera Holding Base back and forth on the tray in order to adjust your camera to the required position. Tighten the Holding Base Lock to secure.  

2.  After your camera is secure in position, please make sure the lens is fully covered by the blackout shade. Pull on the tether to ensure there isn’t any light leakag
  • How to store after use
    After use, please fold the teleprompter’s shade and gently put down the Beam Splitter Glass as shown in the image.

    • Before folding away the beam splitter glass, please be sure to return the camera tray back to its original height first to prevent it from coliding with the glass

How to Use

  • Download and install the APP for the teleprompter

    iOS

    Android

  • Scan the QR code above (respectively for iOS and Android) with your phone or tablet to download and install the APP for the teleprompter.

  • Connect your phone or tablet to the remote via the APP

    1.  Long press the ” ” button to turn on the remote. A blue indicator will flash on the screen.
    2. Activate the Bluetooth on your phone or tablet, log in the teleprompter APP, search for the Bluetooth signal “NEEWER RT110”, and select to connect with the remote.
  •  Control the teleprompter using the remote

    1. Short press the button to play text on the teleprompter. Short press the button again to pause.
    2. When playing, short press the “A+”/”A-” button to zoom in or zoom out; short press the””/”” button to slow down or speed up.
    3. When paused, short press the “”/” “button to move the page up or down.

Note

  1.  The teleprompter has fragile components and should be handled carefully to avoid accidentally dropping or subjecting it to physical impact.
  2. Please do not try to dismantle the product. Should you notice a defect, please contact Neewer Customer Service or maintenance staff authorized by Neewer to repair.

Specifications

Model:   X17
Size :  380380115 mm
Material : Material Aluminum alloy+specialized coating glass

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals