Hanwha Vision SMT-2731PV AI Public View Monitor User Manual

PUBLIC VIEW MONITOR
SMT-2731PV
SMT-3231PV

SAFETY INSTRUCTIONS

1. WARNING
   To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
   Do not insert any metallic object through the ventilation grills or other openings on the equipment.
   Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
   To prevent injury, this apparatus must be securely attached to the Wall/ceiling in accordance with the installation instructions.

2. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE REAR COVER. NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

3. EXPLANATION OF GRAPHICAL SYMBOLS
   The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of “dangerous voltage: within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
   The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
ATTENTION
IL Y A RISQUE D’EXPLOSION SI LA BATTERIE EST REMPLACÉE PAR UNE BATTERIE DE TYPE INCORRECT. METTRE AU REBUT LES BATTERIES USAGÉES CONFORMÉMENT AUX INSTRUCTIONS.
※ This device has been verified using STP cable. The use of appropriate GND grounding and STP cable is recommended to effectively protect your product and property from transient voltage, thunderstroke, communication interruption.
※ Select an installation site that can hold at least 4 times the monitor weight.

overview

PACKAGE CONTENTS
Please check the following contents are included in addition to the main unit.

| |
---|---|---
Public View Monitor| Quick Start Guide| Alarm terminal block
| |
Remote Controller| Battery| Power Inverter Harness

SEPARATELY SOLD PRODUCT

The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE 802.3bt shall be a UL Listed device with the output evaluated as a Limited Power Source as defined in UL60950-1 or PS2 as defined in UL62368-1.

NAMES AND FUNCTIONS OF EACH PART
Front

ON – GREEN
OFF – RED
4| IR Receiver| Receive IR signal from Remote Controller.

Back

settings.
▪ If you forget your password, use the RESET button.
8| Micro SD card slot| Compartment for the Micro SD card.

• Detach the terminal cover by rotating the fastening screw in a counterclockwise direction to loosen it, then connect the cable.
• This product is intended to be supplied by a UL Listed Power Supply Unit marked “Class 2” or “LPS” or “PS2”.
• This product dose not support LLDP.

REMOTE CONTROL

• Those buttons without specific description are deprecated buttons.

connecting with other device

THINGS TO CHECK BEFORE CONNECTION
**Check before connecting

**

• When connecting, refer to the instruction manual of the product to be connected. The number and position of external devices may differ depending on the product.
• Do not connect the power until all connections are complete. Connecting the power supply during connection may damage the product.
• Check the type of terminal behind the product you want to connect.

CONNECTING WITH EXTERNAL DEVICES
HDMI cable connection method

Powering and networking

menu settings

OSD MENU SETTING
Selecting OSD menu

You can select the OSD menu by pressing the [MENU/EXIT] button on the remote controller.

1. Press the MENU/EXIT button to enter the main menu.
2. Press the ▲/▼ buttons to select the main menu, and then press the ENTER or ► button.
3. Press the ▲/▼ buttons to select the sub-menu, and then press the ENTER or ► button.
4. Press the ▲/▼ buttons to adjust the adjustment value.
5. Press the MENU/EXIT button to exit.

Input Source

1. Press the MENU/EXIT button to enter the main menu.
2. Press the ▲/▼ button to select , and then press the ENTER or + button.

• HDMI 1: Select external HDMI1 input
• HDMI 2: Select external HDMI2 input
• CAMERA: Select internal Camera input

Brightness/Contrast

1. Press the MENU/EXIT button to enter the main menu.
2. Press the ▲/▼ button to select <Brightness/Contrast>, and then press the ENTER or ► button.

• Brightness: Adjusts the brightness of the screen. (Adjust 0 ~ 100)
• Contrast: Adjusts the difference in brightness between the object and the environment. (Adjust 0 ~ 100)

Color Setting

1. Press the MENU/EXIT button to enter the main menu.
2. Press the ▲/▼ button to select , and then press the ENTER or + button.

• Gamma: Adjust the mid-range brightness (Gamma) of the screen. (1.8/2.0/2.2/2.4/2.6)
• Picture Mode: Select a screen mode appropriate for your viewing environment. (Standard/Photo/ Movie/Game)
• Color Temp.: The color temperature can be adjusted and used depending on the monitor color. (Warm/Normal/Cool/USER)
• Hue: Adjusts the color of the screen. (Adjust 0 ~ 100)
• Saturation: Adjusts the saturation of the screen. (Adjust 0 ~ 100)

Picture Quality Setting

1. Press the MENU/EXIT button to enter the main menu.
2. Press the ▲/▼ button to select , and then press the ENTER or + button.

• Sharpness : Adjusts the sharpness of the screen. (Adjust 0 ~ 100)

Display

1. Press the MENU/EXIT button to enter the main menu.
2. Press the ▲/▼ button to select , and then press the ENTER or ► button.

• Aspect Ratio : You can select a screen size you want. (Wide Screen/4:3/1:1/Auto)

Audio

1. Press the MENU/EXIT button to enter the main menu.
2. Press the ▲/▼ button to select

• Mute: You can set whether to use the mute function. (On/Off)
• Volume: You can adjust the volume. (Adjust 0 ~ 100)

Multi-Window

1. Press the MENU/EXIT button to enter the main menu.
2. Press the ▲/▼ button to select , and then press the ENTER or ► button.

• Multi-Window : You can select Picture in Picture (PIP) or Picture by Picture (PBP) mode. (Off/PIP Mode/PBP 2Win)
• Sub Win2 Input : Displays the currently output Sub Win2 Input. (HDMI1/CAMERA)
• PIP Size : You can adjust the size of the sub-screen in PIP mode. (Small/Medium/Large)
• PIP Position : You can adjust the position of the sub-screen in PIP mode. (TopRight/TopLeft/ BottomRight/BottomLeft)
• Swap : You can switch between the main screen and sub-screen in PIP or PBP mode.

OSD

1. Press the MENU/EXIT button to enter the main menu.
2. Press the ▲/▼ button to select , and then press the ENTER or ► button.

• Language: Select the screen language. (English/Español/Français)
• OSD H-Position: Moves the screen of the menu to the left or right. (Adjust 0 ~ 100)
• OSD V-Position: Moves the screen position of the menu up or down. (Adjust 0 ~ 100)
• OSD Transparency: Sets the transparency of the menu screen. (Adjust 0 ~ 100)
• OSD Time Out: The menu screen disappears if the screen does not change for a certain period of time. (Adjust 0 ~ 100)
• OSD Rotation: You can rotate the menu screen. (Normal/90/180/270)

Other

1. Press the MENU/EXIT button to enter the main menu.
2. Press the ▲/▼ button to select , and then press the ENTER or ► button.

• USB Update FW : The monitor can be updated by connecting a USB to the USB port. (Idle/Writing)
• Reset : Resets the monitor settings to default.

network connection and setup & webviewer

You can set up the network settings according to your network configurations.

CONNECTING THE PVM DIRECTLY TO LOCAL AREA NETWORKING
Connecting to the PVM from a local PC in the LAN

1. Launch an Internet browser on the local PC.
2. Enter the IP address of the PVM in the address bar of the browser.

• A remote PC in an external Internet out of the LAN network may not be able to connect to the PVM installed in the intranet if the port-forwarding is not properly set or a firewall is set. In this case, to resolve the problem, contact your network administrator.
• By factory default, the IP address will be assigned from the DHCP server automatically.
  If there is no DHCP server available, the IP address will be set to 192.168.1.100.
  To change the IP address, use the Device Manager.
  For further details on Device Manager use, refer to “Using Device Manager”. ( Page 20)

CONNECTING THE PVM DIRECTLY TO A DHCP BASED DSL/CABLE MODEM

1. Connect the user PC directly with the PVM.
2. Run the Device Manager and change the IP address of the PVM so that you can use the web browser on your desktop to connect to the Internet.
3. Use the Internet browser to connect to the web viewer.
4. Move to [Setup] page.
5. Move to [Network] – [DDNS] and configure the DDNS settings.
6. Move to [Basic] – [IP & Port], and set the IP type to [DHCP].
7. Connect the PVM, which was removed from your PC, directly to the modem.
8. Restart the camera.

• For information on how to set DDNS, refer to the online help of Web Viewer.
• For information on how to set the IP format, refer to the online help of Web Viewer.

USING DEVICE MANAGER

• Device manager program can be downloaded from - menu at Hanwha Vision website (https://www.HanwhaVision.com).
• More instructions of Device Manager can be found at menu of the main page.

AUTOMATICALLY SEARCHING CAMERA
If a camera is connected to the same network of the PC where device manager is installed, you can find network camera by using search function.

1. Click at the main page of device manager.
2. Check the camera from the list.
   ● Check MAC address at the sticker attached to the camera.

CONFIGURING IP ADDRESS
If you want to change camera network setting, sign must be displayed at . Click at the main page to log in.

Configuring Static IP

Manually insert and configure IP address & port information.

1. Click the camera from the list that you want the change the IP setting.

2. Click at the main page of device manager.

3. Select .
   ● IP information of the camera will be displayed as previously set.

4. Fill in IP & Port related categories.

If not using a Broadband Router
For setting , , and , contact your network administrator.

• HTTP Port : Used to access the camera using the Internet browser, defaulted to 80.
• RTSP Port: A port that controls real-time streaming. The initial value is 554.

If using a Broadband Router

• IP Address : Enter an address falling in the IP range provided by the Broadband Router.
  ex) 192.168.1.2~254, 192.168.0.2~254, 192.168.XXX.2~254

• Subnet Mask : The of the Broadband
  Router will be the of the camera.

• Gateway : The of the Broadband Router will be the of the camera.

• The settings may differ depending on the connected Broadband Router model.
  For more information, refer to the user manual of the applicable router.

• For more information about port forwarding of the broadband router, refer to “Port Range Forward (Port Mapping) Setup”. ( Page 23)

If the Broadband Router has more than one camera connected
Configure the IP related settings and the Port related settings distinctly with each other.
ex)

Subnet Mask
Gateway| 192.168.1.100
255.255.255.0
192.168.1.1| 192.168.1.101
255.255.255.0
192.168.1.1
Port related settings| HTTP Port RTSP Port| 8080
554| 8081
555

◼ If the is set other than 80, you must provide the number in the address bar of the Internet browser before you can access the camera.
ex) http:// IP address : HTTP Port
http://192.168.1.100:8080
5. Click [Apply] Button.
6. If the success message is displayed, click [OK].

Configuring Dynamic IP

Receive IP address from DHCP
● Example of the Dynamic IP environment
– If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server
– If connecting the camera directly to modem using the DHCP protocols
– If IPs are assigned by the internal DHCP server via the LAN

1. Click the camera from the list that you want to change the IP setting.
2. Click at the main page of device manager.
3. Select <Obtain an IP address automatically (DHCP)>.
4. Click [Apply] button.
5. If the success message is displayed, click [OK].

MANUALLY REGISTERING CAMERA
If the camera cannot be found using search function, the camera can be registered remotely by manually inserting IP information, if the camera is connected to external network.

1. Click – at the main page of device manager.
2. Insert the range of IP address that you search.
3. Select the of the camera that you register, and insert HTTP port, ID, and password.
4. Click [Register] button.
5. Check if camera is registered.
   ● Check MAC address at the sticker attached to the camera.

AUTOMATICALLY CONFIGURING IP

1. Click the camera from the list that you want to automatically configure the IP.

2. Click < + > at the main page of device manager.
   ● Equipment Setting menu appears.

3. At the menu, click .

4. Click [Close] button.

PORT RANGE FORWARD (PORT MAPPING) SETUP
If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the Broadband Router so that a remote PC can access the camera in it.

Manual Port Range Forwarding

1. From the Setup menu of the Broadband Router, select <Applications & Gaming> – .
   For setting the port range forward for a third-party Broadband Router, refer to the user guide of that Broadband Router.

2. Select and for each connected camera to the Broadband Router.
   The number of each port to be configured to the IP router should be set according to the port number designated in – – <IP & Port> on the camera web viewer.

3. When done, click [Save Settings]. Your settings will be saved.

• Port forwarding setting is an example of setting CISCO IP router.
• The settings may differ depending on the connected Broadband Router model.
  For more information, refer to the user manual of the applicable router.

Setting up Port Range Forward for several network cameras

• You can set a rule of Port Forwarding on the Broadband Router device through its configuration web page.
• A user can change each port using the camera setting screen.

When Camera1 and Camera2 are connected to a router :

• Port forwarding can be done without additional router setup if the router supports the UPnP (Universal Plug and Play) function.
  After connecting the network camera, select the checkbox from the menu <Quick connect> in in “Settings -> Network -> DDNS”.

CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC

1. Run device manager.
   It will scan for connected cameras and display them as a list.

2. Double-click a camera to access.
   The Internet browser starts and connects to the camera.

• Access to the camera can also be gained by typing the camera’s IP address in the address bar of the Internet browser.

CONNECTING TO THE CAMERA FROM A REMOTE PC VIA THE INTERNET
On a remote computer that is not in the Broadband Router’s network cluster is not allowed, users can access cameras within a Broadband Router’s network by using the camera’s DDNS URL.

1. Before you can access a camera in the Broadband Router network, you should have set the port range forward for the Broadband Router.
2. From the remote PC, launch the Internet browser and type the DDNS URL address of the camera, or the IP address of the Broadband Router in the address bar.
   ex) http://ddns.hanwha-security.com/ID

• To use DDNS, sign up at the DDNS homepage (http://ddns.hanwha-security.com) and register the product at [My DDNS]>[Register Product].

CONNECTING TO THE CAMERA
Normally, you would

1. Launch the Internet browser.
2. Type the IP address of the camera in the address bar.
   ex)
   • IP address (IPv4) : 192.168.1.100 → http://192.168.1.100
   – the Login dialog should appear.
   • IP address (IPv6) : 2001:230:abcd: ffff:0000:0000:ffff:1111
   → http://[2001:230:abcd:ffff:0000:0000:ffff:1111] – the Login dialog should appear.

If the HTTP port is other than 80

1. Launch the Internet browser.
   Type the IP address and HTTP port number of the camera in the address bar.
   ex) IP address : 192.168.1.100:HTTP Port number(8080)
   → http://192.168.1.100:8080 – the Login dialog should appear.

Using URL

1. Launch the Internet browser.
2. Type the DDNS URL of the camera in the address bar.
   ex) URL address: http://ddns.hanwha-security.com/ID
   – the Login dialog should appear.

• Network connection is disabled in the LAN only environment.

Connecting via UPnP

1. Run the client or operating system in support of the UPnP protocol.
2. Click the camera name for search.
   In the Windows operating system, click the camera name searched from the network menu.
   – The login window is displayed.

Connecting via Bonjour

1. Run the client or operating system in support of the Bonjour protocol.
2. Click the camera name for search.
   In the Mac operating system, click the camera name searched from the Bonjour tab of Safari.
   – The login window is displayed.

To check the DDNS address
If the camera is connected directly to a DHCP-based cable modem or DSL modem, the IP address will change each time it tries to connect to the ISP (the company you subscribed to).
If this is the case, you will not be informed of the IP address changed by DDNS.
Once you register a dynamic IP-based device with the DDNS server, you can easily check the changed IP when you try to access the device.
To register your device to the server, visit http://ddns.hanwha- security.com and register your device first, and then set the Web Viewer’s