Minoston Meter MP21ZP Meter Switch User Manual
- June 12, 2024
- Minoston
Table of Contents
Minoston Meter MP21ZP Meter Switch
Product Information
Item| Power Supply| Signal(Frequency)| Operating Temperature Range| Generic
Type| Specific Type
---|---|---|---|---|---
Meter Switch User Manual| | | | |
Product Usage Instructions
Button Function Description
- Add or Remove the device
- Press the button three times to add or remove the device into the network.
- press 3x Button : Add/Include or Remove/Exclude the device into network.
- Factory Reset
- press twice and then press and hold the button for about 10 seconds until the BLUE indicator flashes.
Factory Reset
Press the button twice and then press and hold the button for about 10 seconds until the BLUE indicator flashes.
Adding Your Device To Hub
Network Wide Inclusion To A Z-Wave Network
Refer to your primary controller instructions to process the inclusion/exclusion setup procedure. When prompted by your primary controller, click the z-wave button three times.
- The device support two methods of inclusion, When using a Z-Wave Plus™ certified controller choose Network Wide Inclusion or Smart Start.
- Network Wide Inclusion To A Z-Wave™ Network
- Refer to your primary controller instructions to process the inclusion/exclusion setup procedure.
- When prompted by your primary controller, click the z-wave button three times.
- The device is compatible with Smart Start.
Smart Start enabled products can be added into a Z-Wave™ network by scanning the Z-Wave QR Code found on the top of the outlet or the back of the box with a controller providing Smart Start inclusion. No further action is required and the Smart Start product will be added automatically within 10 minutes of being switched on and in the network vicinity.
Smart Start Inclusion
The device is compatible with Smart Start. Smart Start enabled products can be added into a Z-Wave network by scanning the Z-Wave QR Code found on the top of the outlet or the back of the box with a controller providing Smart Start inclusion. No further action is required and the Smart Start product will be added automatically within 10 minutes of being switched on and in the network vicinity.
Command Class
The device supports the following command classes:
- Z-Wave Plus Info
- Security 2
- Supervision
- Transport Service
- Basic
- Association
- Multi Channel Association
- Manufacturer Specific
- Device Reset Locally
- Power Level Indicator
- Firmware Update Meta Data
- Configuration
- Notification
- Meter Switch Binary
Association Group Information
| Command Class Name | Version | Required Security Class |
|---|---|---|
| Z-Wave Plus Info | V2 | none |
| Security 2 | V1 | none |
| Supervision | V1 | none |
| Transport Service | V2 | none |
| Basic | V2 | highest granted |
| Association | V2 | highest granted |
| Multi Channel Association | V3 | highest granted |
Meter Information
| Type | Base Type | Scale | Precision | Overload Threshold |
|---|---|---|---|---|
| Current | Electric | A | 2 | 16.5A |
| Voltage | Electric | V | 2 | 135.0V |
| Power | Electric | W | 1 | 2000W |
| Electricity | Electric | KWH | 3 |
Indicator Command Class
The indicator (blue color) will flash according to the indicator set command
received from HUB.
Association Group
| ID | Name | Node Count | Profile | Function |
|---|---|---|---|---|
| 1 | Lifeline | 5 | General: Lifeline | Device Reset Locally Notification: Issued |
when Factory Reset is
performed. Indicator Report: Issued when included successfully.
Switch Binary Report: Issued when output status is changed.
Notification: Issued when current, voltage or power is overload
Meter report: Issued when current, voltage or power is overflow the
threshold.
2| Basic Set| 5| Control: Key 1| Basic Set : Issued when local state is
changed
Configuration Parameters
| Number | Name | Information |
|---|---|---|
| 1 | Reaction of led |
Specifications
Notification
Meter
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>