BONECO S450 Warm Mist Steam Humidifier Instruction Manual

BONECO S450 Warm Mist Steam Humidifier

TECHNICAL DATA

INTRODUCTION

HEALTHY AIR IS A BASIC NEED

There is little to which we react with greater sensitivity than poor air. And yet many people do not pay enough attention to air quality, which has consequences for health and quality of life. This makes us all the more pleased that you have chosen a BONECO appliance to ensure that the basic need for healthy room air is satisfied for you and the people around you.

AVAILABILITY OF ACCESSORIES

You can obtain replacements for worn-out accessories as well as additional accessories from:

• At your BONECO specialist dealer,
• At www.shop.boneco.com or
• Directly via the “BONECO healthy air” app.

ITEMS INCLUDED

OVERVIEW AND PART NAMES

1. Steam tube cover with fragrance container
2. Appliance cover
3. Water tank
4. Water tank cap
5. Water level indicator
6. Control panel
7. Steam output
8. Steam tube
9. A451 Anti-Mineral-Pad
10. Power cord

BUTTONS AND SYMBOLS

Control Buttons

• Switch the appliance on and off / Start cleaning
• Controlling output / Output button
• Access the timer function
• AUTO / SLEEP mode
• Setting relative humidity level / Setting buttons

STARTING UP

IMPORTANT NOTES
Always use the tank to fill in water.
Never fill water directly into the appliance or the steam tube!

• A sound indicates that the appliance is supplied with power.
• Please note that the appliance emits operation noise at an elevated level for the first few minutes after starting up.
• The appliance is in AUTO mode after switching on.

1. Remove the appliance cover.

2. Remove the water tank.

3. Remove the steam tube.

4. Put the A451 Anti-Mineral-Pad in the evaporator basin.

5. Insert the steam tube.

6. Fill cold tap water in the water tank.

7. Insert the water tank.

8. Attach the appliance cover.

9. Connect the appliance to a power outlet.

10. Switch on the appliance.
    

SETTING RELATIVE HUMIDITY LEVEL

ABOUT THE HYGROSTAT

The appliance is fitted with a hygrostat. It measures the relative air humidity and automatically switch-es off humidification in the appliance when the desired value is reached. The internal ventilation remains switched on to guarantee an exact display of the relative humidity level. If the relative humidity falls below the desired level, the humidification automatically switches on again.
A relative humidity of between 40% and 60% is recommended. The setting for the relative humidity ranges from a minimum of 30% to a maximum of 70% or “Co” continuous operation.

SETTING RELATIVE HUMIDITY LEVEL

The setting buttons allow the user to select the de-sired relative humidity level in steps of 5%:

During the selection process, the desired value is blinking. The word DESIRED appears on the display.

After a few seconds, the display automatically switches to the value of the current relative humidity and reads CURRENT. When the desired value is reached, the display reads both DESIRED and CURRENT.

DISPLAY “E2”

When “E2” appears on the display, the current relative humidity level has reached 90%. The appliance automatically switches off for safety reasons. Once the relative humidity level falls below 85% again, the appliance switches on again.

QUICK DISPLAY

When the appliance is switched off, the current relative humidity can be shown in the display by briefly pressing the setting buttons:

This display automatically goes out after a few seconds.

OPERATING MODES

AUTO MODE

When switched on, the appliance is in AUTO mode, which is indicated by this symbol:

AUTO

The desired relative humidity level is preset to 50% in AUTO mode. The appliance selects the suitable performance level Low “L” / Medium “M” / High “H” to reach the relative humidity value of 50% as soon as possible.
In AUTO mode, the target value can be modified at any time using the output button. This switches off AUTO mode, and the appliance is now in manual mode:

SLEEP MODE

Pressing the SLEEP button allows for switching from AUTO mode to SLEEP mode and back:

The desired relative humidity level is pre-set to 45% in SLEEP mode. The appliance selects the suitable performance level Low “L” / Medium “M” to reach the value of 45% using as little energy as possible:

In SLEEP mode, the relative humidity level can be modified at any time using the setting buttons.
If the performance level is modified using the output button, SLEEP mode switches off automatically, and the appliance is then in manual mode:
Pressing the SLEEP button twice activates SLEEP mode again.

MANUAL MODE

The appliance can be operated at three performance levels. Pressing the output button switches between the low “L” (night mode), medium “M” (normal mode) and high “H” (high performance mode) levels:
The desired performance level is shown in the display:

TIMER

ABOUT THE TIMER

The appliance has a switch-off timer and a switch-on timer.

SWITCH-OFF TIMER

Pressing the timer button while the appliance is switched on sets the switch- off timer:
The display now indicates (blinking) after what time the appliance will be switched off:

You can use the setting buttons to set the switch-off time in a range from 0h to 9h. After three seconds without input, the set value is activated, and the timer symbol is displayed.
The display again indicates the current relative humidity level. You can press the timer button once more to check or change the time that remains until switching off.

SWITCH-ON TIMER

Pressing the timer button while the appliance is switched off sets the switch- on timer:
The display now indicates (blinking) after what time the appliance will be switched on:

You can use the setting buttons to set the switch-on time in a range from 0h to 9h. After three seconds without input, the set value is activated. The display shows the set switch-on time and the timer symbol.
The appliance is in AUTO mode after switching on.

CLEANING

ABOUT THE CLEANING SYMBOL

The cleaning symbol in the display indicates that the appliance must be cleaned:
The symbol automatically goes off when descaling mode is ended.
To make the symbol disappear manually, press both setting buttons at the same time for about five seconds.

DESCALING MODE

Descaling mode allows for easy cleaning and descaling of the evaporator basin, water base and steam tube.
Only use CalcOff for descaling. Damage caused by other descaling agents is excluded from the warranty.

DESCALING

Make sure that no water flows into the ventilation opening.

1. Remove the A451 Anti-Mineral-Pad.

2. Dissolve one bag of A7417 CalcOff in 1 liter (0.26 US gal) of hot water.

3. Pour the solution directly into the water base.

4. Insert the steam tube.

5. Put the appliance cover back on.

6. Press the cleaning button for five seconds:
   The appliance switches to descaling mode. The dis-play shows the timer symbol and the value “4h”.
   You can use the setting buttons to set the descaling between 1h to 9h depending on the degree of limescale build- up. The value is accepted after three seconds without input.
   The appliance heats the mixture every 30 minutes and switches off again after. You can adjust the cleaning time at any time using the setting buttons. After the cleaning process has been completed, the value “0h” is displayed and the cleaning symbol blinks. Press the power button to terminate descaling mode and switch off the appliance.

7. Drain the appliance and thoroughly rinse the basin with tap water.

CONSUMABLES

You can obtain A7417 CalcOff from your BONECO specialist dealer or the BONECO online store: shop.boneco.com

A451 ANTI-MINERAL-PAD

ABOUT THE A451 ANTI-MINERAL-PAD

The A451 Anti-Mineral-Pad absorbs most of the calcium during operation. It minimizes the excess limescale build-up in the evaporator basin and reduces the frequency of the need for descaling.
Once the A451 Anti-Mineral-Pad is completely filled with calcium, it must be replaced. You can recognize a full pad by its solid feel. Depending on the degree of water hardness, replacement can be necessary every two to four weeks. The A451 Anti-Mineral-Pad can be disposed of with household waste.
There may be boiling water in the evaporator basin! Remove the pad only after the water has cooled.
Put only one pad into the evaporator basin.

A451 ANTI-MINERAL-PAD

1. Remove the appliance cover.

2. Remove the water tank.

3. Remove the steam tube.

4. Replace the used A451 Anti-Mineral-Pad.

5. Put the appliance back together by following the steps in reverse order.

CONSUMABLES

You can obtain a replacement for the used A451 Anti-Mineral-Pad from your BONECO specialist dealer or the BONECO online store:
shop.boneco.com

CLEANING INTERVALS

RECOMMENDED CLEANING INTERVALS

fill with fresh water
Every 2 weeks| Clean water tank, appliance cover, fragrance container and steam tube with dish detergent and a soft plastic brush and rinse well
Every 2 to 4 weeks| Check A451 Anti-Mineral-Pad and replace if necessary
Annually| Clean the housing with a damp cleaning cloth and wipe dry; use a cleaning agent suitable for plastic as necessary

www.boneco.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>