PRODVX IPPC-10SLB Panel PC LED User Guide
- June 3, 2024
- Prodvx
Table of Contents
PRODVX IPPC-10SLB Panel PC LED
This package contains
Please note that it is preferred not to use power tools to attach the device to the mount or stand.
How to start
- Step 1: Take contents out of the box, and make sure all components are present.
- Step 2: Install wall/glass mount or desk stand using a manual screwdriver, check the designated mount/stand manual for instructions.
- Step 3: Connect to power via a power adapter or PoE+. If using the power adapter, please remove the rubber plug before inserting the power cable if applicable.
- Step 4: Connect to the Internet through Wi-Fi, PoE+, or LAN.
- Step 5: If applicable, install and configure the preferred application.
Quick connection settings
- Step 1: Plug in the power cable to turn on the display. To connect to Wi-Fi, navigate to the bottom toolbar and click the globe icon as seen in the image below.
- Step 2: Select the desired Wi-Fi network, click “connect” and fill in the credentials to connect.
Important notice
Whenever you want to switch between a Wi-Fi connection and an ethernet
connection, the following procedure can be used:
- When powering on the device, select Wi-Fi by pressing and holding the volume plus button.
- If you would like to switch back to the ethernet connection, make sure the device is powered down. After that, press and hold the volume minus button while turning on the device to revert back to the ethernet.
If the procedure is performed correctly, a notification will be shown stating which connection is now active.
Optional accessories
- Barcade scanner
- NFC module
- Camera
FCC STATEMENT
Caution:
Please note this product contains a small clock battery. Please return the
product to a certified repair centre for proper replacement of the battery;
battery disposal can be dangerous.
WARNING:
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment. Do not interrupt the power provisioning (power adapter of Poe+
source) to the device when the device is in operation and/or the power
indicator led is green. This may cause a malfunction of the device and could
lead to damaging the internals.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area can cause harmful interference, in which case the user will
be required to correct the interference at their own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Europe/UK- EU/UK Declaration of Conformity
This device complies with the essential requirements of the Radio Equipment
Directive (2014/53/EU ). The following test methods have been applied in order
to prove the presumption of conformity with the essential requirements of the
Radio Equipment Directive. This equipment is compliant with Class A of EN
55032. In a residential environment, this equipment may cause radio
interference.
Correct Disposal of this product.
‘0-‘ This marking indicates that this product should not be disposed of with
other A (household) waste. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, recycle it responsibly to
promote the sustainable reuse of material resources. To return your used
device, please use the return and collection systems or contact the reseller
where the product was purchased. They can take this product for
environmentally safe recycling.
“FCC & CE RF Radiation Exposure Statement Caution: To maintain compliance with the FCC & CE’s RF exposure guidelines, the product must be placed at least 20 cm from nearby persons.”
The guaranteed environmental specifications for the ProDVX Display and accessories are:
- Operating temperature:: 0- 40 °c / 32 – 104 °F
- Storage temperature: -10 – 55 °C/ 14- 13 1 °F
- Relative humidity: 10 – 85% at 40 °C/ 104 °F non-condensing.
Please check the website or scan the QR code for more product information. www.prodvx.com/support.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>