UHPPOTE HBK-D01 Proximity Rfid Card Reader User Manual
- May 15, 2024
- UHPPOTE
Table of Contents
HBK-D01
WIEGAND RFID READER
USER MANUAL
Introduction
The RFID card reader can’t work alone and it needs to work with wiegand
protocol access controller, such as access control panel, fingerprint device
or master controller.
It uses ST MCU to ensure stable performance, and low-power circuit makes the
service life longer.
Features
- Waterproof, conforms to IP66.
- Support wiegand 26bits or wiegand 34bits output format.
- The maximum reading distance is 2-23/64″ [6cm] .
- Ultra-low power consumption, the standby current is less than 50mA.
- Fast response speed, the door opening time is less than 0.3s.
- It is useful for safety door system, easy to connect and use.
- Widely used in factories, houses, residential quarters, offices, mechanical and electrical control equipment and so on.
Specification
| Working Voltage | 12VDC | Static Current | ≤50mA |
|---|---|---|---|
| Working Humidity | 10%-90%RH | Frequency | 125KHz |
| Product Weight | 2.96oz [84g] | Card Type | EM-ID |
| Lead Cable Length | 9-27/32″ [250mm] | Waterproof Rating | IP66 |
| Enclosure Material | ABS Plastic | Panel Material | PC Plastic |
| Status Indication | Bi-color LED + Buzzer | Communication Distance | <328′ |
| Enclosure Size | 3-35/64″ x 1-49/64″ x 3/4″ [90x45x19mm] | ||
| Working Temperature | -40 to +140°F [-40 to +60°C] | ||
| Output Format | Wiegand 26bits (default), Wiegand 34bits (optional) | ||
| LED Status Indication | Red means standby, Green means activated |
Wiring Definition
| Color | Functionality | Description |
|---|---|---|
| Red | +12V | +12V power input |
| Black | GND | GND |
| Green | D0 | Wiegand output D0 |
| White | D1 | Wiegand output D1 |
| Blue | LED | LED signal feedback |
| Yellow | BEEP | Buzzer signal feedback |
| Gray | Wiegand 34bits | Optional |
Note:
If the output format of the card reader you want is Wiegand 34bits, please
connect the Gray wire and the Black wire together.
Installation
- Remove the back cover from the reader
- Drill 2 holes on the wall for the self-tapping screws and 1 hole for the cable
- Put the supplied plastic anchors into the 2 holes
- Fix the back cover firmly on the wall with 2 self-tapping screws
- Thread the cable through the cable hole
- Attach the reader to the back cover
Wiring Diagram
Cable of Reader
Red: +12V
Black: GND
White: D1
Green: D0
Blue: LED
Yellow: BEEP
Gray: WG34
Sound and Light Indication
| Operation Status | LED Indicator | Buzzer |
|---|---|---|
| Standby | Red | |
| Read authorized card | Green | A short beep |
| Read un-authorized card | Flash red 3 times | 3 short beeps |
Remarks: The card reader will prompt sound and light indication only when the LED and BEEP cables are connected to the access controller.
Warm Tips
- Confirm the voltage (12VDC) and differentiate positive anode and cathode of the power supply.
- About the wiring between the reader and the controller, the wire should be 22 AWG at least and the length should not exceed 100 meters.
- When external power is used, suggest to use same power GND with controller panel. It is recommended to use multi-strand twisted pair cable to connect card reader to access controller.
- There is no need to wire the LED and BEEP cables if you do not need the card reader to prompt an authorized card through sound and light.
Packing List
| Name | Quantity | Remarks |
|---|---|---|
| Card Reader | 1 | |
| User Manual | 1 | |
| Plastic Anchors | 2 | Used for fixing |
| Self-Tapping Screw | 2 | #7 x 1″, used for fixing |
Packaging Details
After opening the package, please make sure the card reader is in good condition and confirm below accessories are complete or not.
| |
---|---|---
Card Reader x1| Accessories Package x1| User Manual x1
FCC Warning
FCC ID: 2A4H6HBK-D01
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interfere-
nce by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipmentinto an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, this equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>