SHIHOT 6204 Bedroom Ceiling Fans with Lights and Remote Owner’s Manual

SHIHOT 6204 Bedroom Ceiling Fans with Lights and Remote

Specifications

• Product: Small iron cage fan light
• Model No: 6204
• Owner’s Manual: Included

Product Usage Instructions

Important Safety Instructions

1. Read all instructions and safety information before installing the fan.
2. Before installing the fan, disconnect the power by removing fuses or turning off circuit breakers.
3. Ensure all electrical connections comply with local codes.
4. Allow a minimum clearance of 7 feet from the floor for the fan blades.
5. Use a metal outlet box if mounting on a ceiling outlet box.
6. If mounting to a joist, ensure it can support the fan’s weight.
7. Secure all connections after installation to prevent accidents.
8. Avoid inserting objects into the fan blades while in operation.
9. Turn off the fan before changing its direction.
10. Avoid installing the fan on a sloped ceiling to reduce the risk of electrical shock.

Before Installation
Unpack your fan and check the contents. The parts list includes hanger, hanging scaffold, clamp nut, long suspension rod, two end dental heads, short suspension rod, cross screw, round iron sheet fastener, fan light body, arcuate connector, nut, full tooth rod, lamp panel, lamp bulb, spiked rubber plug, self-tapping screw, remote control, wire connector.

Assembly Instructions

1. Punch holes in the pre-installed lamp positions. Turn off power at the outlet box to avoid electric shock.
2. Position the holes on the mounting strap against the ceiling wall at the mounting location and mark the ceiling with a pencil. Drill a 1/8 inch hole at each marked position.
3. Install embedded parts for lighting fixtures by inserting wall anchors into the drilled holes on the ceiling.

FAQ

• Can I use this fan on a sloped ceiling?
  It is recommended not to install the fan on a sloped ceiling to reduce the risk of electrical shock.

• What should I do if the fan blades are obstructed?
  Ensure that the installation site allows the fan blades to rotate without any obstructions. The fan should have a minimum clearance of 7 feet from the floor to the trailing edge of the blades.

Important Safety Instructions

1. Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

2. Before installing the fan, disconnect the power by removing fuses or turning off circuit breakers.

3. Make sure all electrical connections comply with local codes, ordinances, or
   National Electrical Codes. Hire a qualified electrician or consult a do-it -yourself wiring handbook if you are unfamiliar with installing electrical wiring.

4. Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to the trailing edge of the blades.

5. If you are mounting the fan on a ceiling outlet box, use a metal outlet box. Secure the box directly to the building structure. The outlet box and its support must be able to support the moving weight of the fan ( at least 50 lbs.). Do not use a plastic outlet box. Attach the mounting bracket by using the hardware supplied with the ceiling outlet box.

6. If you are mounting the fan to a joist, make sure it is strong enough to support the moving weight of the fan (at least 50 lbs.)

7. After installing the fan, make sure all the connections are secured. This will prevent the fan from falling.

8. Do not insert anything into the fan blades while the fan is operating.

9. Turn the fan off and wait for it to stop before reversing fan direction.

10. To reduce risk of electrical shock and personal injury, do not install the fan on a sloped ceiling.

11. To reduce the risk of electrical shock and personal injury, do not use this fan with any solid-state.

12. To reduce risk of personal injury, use only the two steel screws and lock washers provided with the fan for mounting the outlet box.

BEFORE INSTALLATION

Unpack your fan and check the contents. You should have followings

Parts List

ASSEMBLY DRAWING & PARTS LIST-WITH LIGHT

1. Punch holes in the pre installed lamp positions
   Turn off power at outlet box to avoid possible electric shock. Position the holes on the mounting strap (b) against ceiling wall at mounting location, and make a marking on the ceiling with a pencil Then drill a 1/8 inch hole at each pencil marked position with churn drill.

2. Installation of embedded parts for lighting fixtures
   Insert wall anchors (c) into the holes drilled on ceilling by gently tapping with a hammer. Make sure the wall anchors are tight and flat with ceiling or beneath ceiling.

3. Install the hanging board
   Secure the mounting strap to the ceiling by threading the tapping screw (d) through the holes on the mounting strap into the wall anchors. Take off the screws on the sides of mounting strap.

4. Connect the suspension tray and suspension rod
   This product is equipped with 2 suspenders, 1 long suspender and 1 short suspender.  The length of the suspender should be selected according to the site during installation, and refer to the right figure for installation

5. Connect the suspension rod to the fan lamp body
   Before connecting, first thread the power cord on the upper end of the fan light body through the suspension rod to the suction cup and pull it out. Then, use screws as shown in the figure to fix the upper suspension rod to the fan light body

6. Install the bottom light panel
   Pass the power cord of the fan lamp body through the open connector, fix the open connector on the fan lamp body, and then firmly connect the power cord of the fan lamp body to the power cord of the lamp panel. After connecting the power cord, fix the full tooth pole on the other end of the open connector, pass the lamp panel through the full tooth pole, and use a ball nut to fix the lamp panel on the fan lamp body, as shown in the figure

Precautions for connecting the power cord :
WARNING
To avoid possible electrica lshock, be sure electricity is turned off at the main fuse box before wiring
Connect 110V main power (dwelling) to theTerminal Block located on the hanger

7. Connect and install the product to the ceiling
   Before connecting the power line, please ensure that the power is cut off. Connect the wires of the same color and insulate them with electrical tape. Thread the hanging plate through the hanging plate screw and fix the lamp body to the hanging plate with a flower nut, as shown in the figure

wire from the outlet box respectively. Wrap each wire connector with electrical tape for a more secure connection.

8. Install light source
   Install the light source onto the fan light panel and complete the installation.

REMOTE CONTROL SETTING AND OPERATION

1. Restore electrical to the outlet box by turning the electricity on at the main fuse box.

2. Remove the battery cover from the remote control transmitter, install the battery, and replace the cover.
   Note:

3. Use 1 12V battery to replace battery.

4. If not using for long periods of time, remove the battery to prevent damage to the remote transmitter, and store the remote transmitter away from excess heat or humidity.

5. The buttons on the remote control transmitter control the fan speed and light as follows.

IMPORTANT:PAIRING BETWEEN REMOTE AND RECEIVER

1. Turn “ON”the power supply and within 30 seconds press and hold the transmitters “FAN ON/OFF”button for 5 seconds and a“beep”will be heard this will then activate a successful pairing and all functions will work normally.
   IMPORTANT:
   pairing initial step must be performed within 30 seconds of power being turned on.

   • when pairing multiple fans please ensure the isolation switch or power supply to the first installed fan is turned off prior to pairing futher fans e.g please pair one fan at a time
   • please ensure isolation switch is kept to the ON position, the isolation switch is not to be used as a light switch as this will damage and make the remote recevier inoperable

2. If the transmitter functions are not working please check the battery orientation and power level.Low battery voltage will affect the functions of your transmitter and operation of your fan.Other remote controls nearby using the same frequency may cause interference with the Fans receiver.

3. Please remove batteries from the transmitter if leaving unused for an extended period of time.

4. Remote supports 200w maximum on lighting side.

IMPORTANT REMAINDERS

1. Please note: Receiver must be correctly installed in the mounting bracket on fan
2. When the transmitter cannot control the receiver, please check the battery hassufficient charge in the transmitter.
3. When the transmitter cannot control the receiver, please check if there is any existence of similar remote controlled products nearby, causing interference with each other.
4. Low power of battery will affect the sensitivity of the transmitter and the signal reception accordingly, must replace if the battery is getting low power.
5. Please take the battery out from the transmitter when leaving unused for a long time, to avoid battery leaks.
6. Isolation Switch “Must be connected in the line.”
7. When power is cut to the unit (via a blackout or otherwise) when power is restored the light will come on.
   Before carrying out any cleaning or maintenance work, always make sure that the appliance is disconnected. LED lights are not removable. LED lights can only be used within the product delivery, they can not be replaced.

PROTECTIVE FUNCTIONS OF THE RECEIVER

• Lock protection- The DC motor has a built-in safety feature against blade or motor obstruction during operation. If something obstructs the fan blades or motor, the motor will keep trying to run and then stop operation after about 30 seconds of interruption. Please remove obstacles and reset. To reset: Turn the fan off by remote transmitter and then turn the fan on.
• Over load protection (current limit)- The device will limit the maximum current output from the receiver/drive if the fan load has increased abnormally.

Tips

1. If your fan is operates automatically after installation and power on, it is because your fan has memorized the previous factory setting. Use the Universal Mode or the learning function and your
   fan will be ready for use.

2. If the fan or light isn’t working, reset power (turn the power off for at least 5 seconds and then turn the power back on) and redo the learn function setting.

3. It is not possible to remotely operate more than one fan in the same room (in the area where the remote signal can reach to) if they share the same power supply. Separate power supplies
   (such as using individual wall switches for each fan) is required if you want to separately control more than one fan in same room.

4. When the fan is turned on or operated using forward/reverse function, it shutters & goes back & forth until it turns.
   This is a normal and it will take a few seconds to run this operation.

MAINTENANCE

1. Periodic cleaning of your new ceiling fan is the only maintenance that is needed.
2. When cleaning, use only a soft brush or lint free cloth to avoid scratching the finish.
3. Abrasive cleaning agents are not required and should be avoided to prevent damage to finish.
   WARNING
   Do not use solvents when cleaning your ceiling fan. It could damage the motor and create the possibility of electrical shock.

RECOMMENDED:
Periodically check that the blade sets to the fan motor setscrews are secure and tight.

BALANCING FAN / WOBBLING TROUBLE SHOOTING

• Please note that all ceiling fans are not the same, even in the same model—some may move more or less than others.
• Movement of a couple of centimeters is quite acceptable and does not suggest the fan will fall down.
• Even though all blades are weighted and grouped by weight, it is impossible to eliminate wobble altogether. This should not be considered a fault. Ceiling fans tend to move during operation due to the fact that they are not generally rigidly mounted.

TRY THE FOLLOWING TO REDUCE A WOBBLING FAN;

1. Check that all of the blade mounting screws are tightened and secure.
2. Wobbling problems may result from inconsistent blade level. To check the blade level, measure the distance from each blade tip to the ceiling. Note: If measurements are inconsistent:
   • Be sure the blade mount screws are not too tight or too loose, which may cause wobbling due to an unlevel blade tip
   • An out of shape blade can cause wobbling. Check by removing the blade and placing on a flat surface.
3. Blade tracking may be checked simply by use of a household ruler. Place the ruler vertically against the ceiling and even with the outside leading edge of a blade. Note the distance of the edge of a blade compared to the others.
   • Turn the blade slowly by hand to check the remaining blades.
   • If a blade is not in alignment, the blade is either out of shape, warped or the blade screws are not evenly tighten or either loose.

BALANCING KIT
A Balancing Kit has been provided to assist with reducing a wobble. Please retain the kit as it may become useful should the fan develop a wobble in the future.

• Step 1. Clamp the balance clip to the middle position marked A of any fan blade. Turn on the fan and check if the vibration of the fan blades is reduced. Proceed to step 3 if the shaking is reduced. If shaking increases go to step 2.
• Step 2. Take out the balance clip, clip it to the middle mark B of the clockwise adjacent blades, and so on until you find the fan blade that can reduce the shaking.
• Step 3. When we found the fan blade that can reduce the shaking. Move the balance clip on the fan blade towards the center or edge and turn on the fan to see if the wobble is reduced. If the balance clip cannot fully counteract the shaking of the fan blade at the center or edge position, you can add an additional balance clip near the center or edge position for adjustment.
• Step 4. When the fan blade no longer shakes, use a balance patch to stick to the position where the clip on the back of the fan blade is clamped to replace the balance clip. (1 balance patch instead of 1 balance clip)
• Step 5. The adjustment is complete.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>