Tong Global ZQ01011 Rechargeable Battery Par Light User Manual
- June 15, 2024
- Tong Global
Table of Contents
Tong Global ZQ01011 Rechargeable Battery Par Light
Product Information
Specifications
- Model : Rechargeable Battery Par Light
- Power Source : Battery
- Remote Control : Yes
- AC Adapter : Included
- Channels : CH1-CH7
- Function Range : 0-255
Product Usage Instructions
Battery Replacement
If the distance required between the remote control unit and main unit
decreases, or the remote control unit’s buttons don’t work, it indicates that
the battery is exhausted. Follow the steps below to replace the battery
- Locate the battery compartment on the remote control unit.
- Open the battery compartment.
- Remove the old battery.
- Insert a new CR2025/2032 battery into the compartment, ensuring the correct polarity.
- Close the battery compartment securely.
Connecting the AC Adapter
To connect and charge the par light using the AC adapter, follow these steps
- Connect the charging port of the par light to the dedicated AC adapter cable.
- Plug the AC adapter into a power socket.
- Observe the charging indicator on the par light. It will slowly change from 25% to 100% as the battery charges.
FAQ (Frequently Asked Questions)
-
Q: Can I use the product with a different voltage?
A: No, this product should only be used with the voltage indicated on the AC adapter. Using it with a different voltage may cause a malfunction, fire, or electric shock. -
Q: Can I use the AC adapter supplied with this product for other equipment?
A: No, using the AC adapter supplied with this product for other equipment may cause a malfunction, fire, or electric shock. It is recommended to use the adapter only with this product. -
Q: What should I do if water gets into the product?
A: If water gets into the product, it may cause a fire or electric shock. Therefore, do not place vases or any other containers with water or liquids on the product.
BEST CUSTOMER SERVICE
QR CODE
CAUTION :DO NOT OPEN THE HOUSING SHOCK HAZARD
RECHARGEABLE BATTERY PAR LIGHT
USER MANUAL
Battery Powered Par Can
- thank you for purchasing this product.
- Be sure to read this user manual before operating the product and use it correctly.
- Store this manual in a safe place for future reference.
Warning If you ignore the following waning’s and use the product incorrectly, it may cause death or serious injury due to fire or electrocution.
|
-
Keep the plug of the AC adapter free form the dust.
-
If there is dirt or dust between the plug of the AC adapter and the power socket, it may cause a fire or electric shock. Remove dirt or dust after removing the plug of the AC adapter from the power socket.
-
Do not use the product with any voltage other than that indicated on the AC adapter.
-
This product is for use within the country of purchase only. It cannot be used in other countries. Do not use the product with any power supply or voltage other than that indicated on the AC adapter. Do not connect the AC adapter to DC power supplies of on ships, etc. Doing so may cause a fire or electric shock.
-
Do not use the AC adapter other than that supplied with this product.
-
Do not use the AC adapter supplied with this product for another equipment.
-
Doing so may cause a malfunction, fire or electric shock.
Doing so may result in electrocution.
- Do not touch the plug of the AC adapter cable when you remove the plug of the AC adapter from the power socket.
- The AC adapter cable may be damaged, and it may cause a fire or electric shock . Be sure to grasp the plug of the AC adapter when removing it from the power socket.
Do not place vases or anything containing water or other liquids on the product. if water gets into the product, it may cause a fire or electric shock
Before using the Unit
-
what’s in the box
-
Confirm the supplied standard accessories.
-
Remote control unit X1
-
Battery(CR2025/2032)for remote control unit X1
-
(The battery has been installed in the remote control unit when shipped from the factory.)
-
Rechargeable par light X1
-
Fixing Screws X2
-
Mounting Brackets x2
-
Dedicated AC adapter X1
-
Owner’s Manual x1
| Channels | Value | Function |
|---|---|---|
| CH1 | 0-255 | Color brightness control(this change should use together with |
CH2,CH3 or CH4 )
CH2| 0| Red light off
1-255| Red brightness from dark to bright
CH3| 0| Green light off
1-255| Green brightness from dark to bright
CH4| 0| Blue light off
1-255| Blue brightness from dark to bright
CH5| 0-7| No strobe flash
8-255| Strobe flash(from slow to fast),the bigger values,the faster
CH6| 0-10| Manual control(CH1-CH5)
11-60| Colors selection(colors contorted by CH7)
61-110| Colors selection(colors contorted by CH7),the bigger values, the
faster
111-160| Colors pulse transform(speed contorted by CH7)the bigger values, the
faster
161-210| Colors transition(colors contorted by CH7),the bigger values, the
faster
211-255| Sound control
CH7| 0-255| Colors selection/colors shade(the bigger values, the faster)
Battery replacement time
If the distance required between the remote control unit and main unit
decreases, or the remote control unit’s button don’t work, the battery is
exhausted. In this case, replace the battery with a new one.
Connecting the AC adaptor
After connecting the charging port to the dedicated AC adapter cable, plug the
adapter into the socket. The charging indicator will slowly change from 25% to
100%
Connecting the DMX signal
The light is available to receive the DMX512 signal ,connect the DMX connector to the panel which marked with “DMX IN”, and connect it to the next light .then, connect to the “DMX IN ”of next light from the “DMX OUT” .The DMX signal terminator is recommended when the lighting signal is connecting. It will avoid to interfere the signal which caused by the electrical noise DMX terminator is a XLR connector, connect with a 12002 resistor between the pin 2 and pin 3 of the XLR connector, and connect it to the OUTPUT socket of the final light. see picture
Remote Control Unit
Notes on using the remote control unit
Even if remote control is used within its effective operation range(10m /35
feet),the unit might not response the remote if there are any obstacles
between them.
Before using them the remote control
when you use the remote control for the first time pull out the insulation
sheet from the rear.
Battery replacement
- The battery has been installed in the remote control unit when shipped from the factory.
- To replace the battery, pull out the battery tray from the rear ,put the lithium-ion battery(CR2025/2032)in with the“+” side facing up, and insert the tray again.
LCD digital display function
| Key-press | Description |
|---|---|
| MENU | DMX control/Color selection/Color fade/Color pulse transform/Colors |
transition/Color flash/Sound control/ Color brightness setting
UP| Increase values
DOWN| Decrease values
ENTER| Confirm button. After pressing this button, all setting values will be
saved.
Operation Instruction
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.