VEVOR SL300 Monitor Desk Mount User Manual

Table of Contents

VEVOR-SL300-Monitor-Desk-Mount-PRODUCT

We continue to be committed to providing you tools with at competitive prices.
Save Half”, “Half Price” or any other similar expressions used by us only represent an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and does not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you are saving half in comparison with the top major brands.

MODEL:SL300

This is the original instruction, please read all manual instructions carefully before operating.
VEVOR reserves a clear interpretation of our user manual.
The appearance of the product shall be subject to the product you received.
Please forgive us that we won’t inform you again if there are any technology or software updates on our product.

WARNING: Read this material before using this product. Failure to do so can result in serious injury.

Assemble only according to these instructions. Improper assembly can create hazards.
Keep the assembly area clean and well-lit.
Keep bystanders out of the area during assembly.
Do not assemble when tired or when under the influence of alcohol, drugs, or medication.
The product capabilities apply to properly and completely assembled products only.
For additional information regarding the parts listed in the following pages, please refer to the Assembly Diagram of this manual. Unwrap and separate all parts in a clean work area.

Use precautions

Use with products heavier than the rated weights indicated may result in instability causing possible injury.
Mounts must be attached as specified in assembly instructions. Improper installation may result in damage or serious personal injury.
Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
Use the mounting screws provided and DO NOT OVER-TIGHTEN mounting screws.
This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

VEVOR-SL300-Monitor-Desk-Mount-FIG-2

Method 1 —–1a
- (Required appliances:4,5,6, 7, 8,9,11,14)
Method 2—–1b
- (Required appliances: 1,2,4,5,9, 10, 11,12, 13
- (The desktop has a hole for item 2 to go through)

Connect With Monitor

Use a wrench (H) to screw the screws (D/E) into the four holes at the back of the monitor to avoid damaging the monitor by over-tightening the screws.

Case 1: Monitor/Arm fall (after installing vour monitor)

Press the arm to make it keep it in a horizontal position and then use the Allen Key to add the screw on the arm.
Turn counter-clockwise(“+ ” direction) to increase gas spring tension till can hold the weight of your monitor.
Note: You may need to turn the screw by many circles to tighten the arm.

Case 2: Monitor/Arm pops up (after installing your monitor)

Press the arm to make it keep it in a horizontal position and then use the Allen Key to adjust the screw on the arm.
Turn clockwise(“- ” direction) to reduce gas spring tension till can stay in the position needed.
Note: You may need to turn the screw by many circles to tighten the arm.

If you feel the pitching angle is too tight or too loose when adjusting the mount, please adjust the Screw VEVOR-SL300-Monitor-Desk-Mount-
FIG-9

Cable management

Adjustable instruction

Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai
Imported to AUS: SIHAO PTY LTD, 1 ROKEVA STREETEASTWOOD NSW 2122 Australia
Imported to the USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730
UK REP Pooledas Group Ltd Unit 5 Albert Edward House, The Pavilions Preston, United Kingdom
Technical Support and E-Warranty Certificate www.vevor.com/support

NEED HELP? CONTACT US!