STORCH 266845 Laser Distance Measuring Device Instruction Manual

ProDist compact plus

Laser distance measuring device
Original instruction
V 02 storch-266845-manual
1 0-2 023

266845 Laser Distance Measuring Device

Scope of Delivery
ProDist compact plus laser distance measuring device, holster bag, wrist strap, 2 x 1.5 Volt AA batteries, operating instructions.
Intended use
The present device is designed for measuring distances, areas and volumes using laser technology. Its use relates to commercial applications only; it must be used in accordance with the local conditions. The device must never be used to indicate/mark positions (like a laser  pointer), or for other purposes in which the laser beam could be directed at persons. The device is designed for use in interior and  exteriorapplications.

Technical specifications

Device: 3 minutes
Estimated battery life| Up to 3,000 to 5,000 single mea- surements
Battery| 2 x 1.5 Volt AA batteries (alkaline)
Optimum operating temperature| 0° C to 40° C
Storage temperature| -20° C to 70° C
Protection class:| IP54
measurements| 123 x 44 x 23 mm
Weight| 95 g (without batteries)

No responsibility is accepted for the accuracy of this information. Subject to technical modifications and errors!

Safety instructions

The device uses a voltage range that can pose a hazard for humans and animals. The device must only be opened and/or disassembled by authorised persons. Similarly, maintenance and repairs must be performed by a qualified electrician or an authorised repair shop. The owner/operator operates the device on their own liability and at their risk.
Before using the device, read and make sure you understand all the instructions in this manual. Failure to observe instructions can cause a risk of laser radiation hazard, electric shock and/or physical injury.
CAUTION: Never attempt to modify the function of the device in any way. This can lead to hazardous laser radiation.
**** LASER BEAM. Never look into the beam. Laser class 2device. Only switch on the laser beam when you are usingthe device. The laser switches off automatically after 30seconds. To switch off the laser manually, tap the button.
Improper execution of operational procedures or the use of operating and adjusting elements in a way other than that specified in this manual can result in hazardous exposure to radiation.
The use of optical instruments such as telescopes to view the laser beam aggravates its potential for eye damage.
The device is equipped with an integrated laser. This is a class 2 laser with a maximum output of 1 mW and a wavelength of 620 – 690 nm. Lasers of this type do not normally cause eye damage. But you should still not look directly into the beam as this can cause
flash blindness.
The laser distance measuring device has the following labels
The label (laser outlet) marks the point at which the digital laser distance measuring device generates its laser light. When using the device, you need to know where the laser light is emitted. Make sure that all users are aware of the dangers related to direct eye contact with the laser beam.

• Do not remove or modify any of the product labels.
• The digital laser distance measuring device is not a toy.

Always keep them in a place that is out of the reach of children. The laser light generated by this device must not be pointed at persons or animals.

• Do not use the device in the presence of children or allow children to operate the device.
• Never position the device so that a person can deliberately or inadvertently look into the laser beam.
• Do not use the device on shiny or reflective surfaces such as sheet steel. The reflective surface could direct the beam back towards the operator.
• Always switch off the device when it is not in use. Leaving the device switched on increases the risk of a person inadvertently looking into the laser beam.
• Never attempt to repair or disassemble the device. If unqualified persons attempt to repair this device, this could result in serious injuries. Any repair worked required on the laser measuring device must be performed by STORCH’s authorised after-sales service.
• Do not operate the device in explosive areas, for example, in the vicinity of flammable liquids, gases, or dust.
• The use of accessories designed for other laser measuring devices can lead to serious injuries.
• Keep batteries out of the reach of children.

Device description and LCD display

overview of functions and controls

On/off measure button

1. Plus button
2. Minus button
3. Button for storing/archiving the measured values
4. Area/volume measurement button
5. Indirect measurement (Pythagoras) button
6. Button for switching the measurement reference point (upper edge/lower edge of the device)
7.  Changing the measuring unit
8. Delete values/Off button

Replacing the batteries

1. Open the battery compartment
2. Insert the batteries, taking the polarity (+/-) into consideration.
3. Fit and close the lid

Battery status

Overview of the LCD display

Laser on

1. Measuring plane
2.  Simple Pythagoras
3. Double Pythagoras
4. Area measurement / Volume measurement
5.  Summary of the measured values
6. Scale
7. Battery display status
8.  Permanent measurement and min/max measurement
9.  Spirit level

Commissioning and settings

Switching the device on and off
Press and hold the button to switch on the unit.
Please follow the description under „Taking measurements“.
– Hold down the button to switch the device and laser off.
The laser switches off automatically after 30 seconds; the
device after 3 minutes.
Delete values
– Briefly tap the button. This deletes previously measured values from the device.
Determining the reference point (figs. of the points) Measurement is set to the bottom edge of the housing. To change this, press the reference point button and select another reference measuring point (top, bottom, corner measurement). An audible tone confirms your selection.
After switching off the device, it reverts to the factory setting and measures from the bottom edge of the device again.
For measurements from one corner, unfold the try square until it latches; then push the try square against the corner with slight pressure. Make sure that the measuring plane is set to “End piece”.

Changing the unit (m, ft. In, ft + in)
Hold down the   button to change the units.
Sound on/off
Hold down the button to switch the sound on/off.

Performing measurements

Single distance measurement
Press the button to enable the laser. The lasersymbol appears in the display, and the red laser dotappears on the surface the laser measuring device is pointed at. Press the button again to start the measuring action. The measured values are shown directly in the display.
Continuous measurement (tracking) and min/max measurement During
continuous measurement, the device is pointed at the object to be measured; the measured values are then updated every 0.5 seconds.
The corresponding minimum and maximum values are shown dynamically in the first and second lines.
For a continuous measurement in min/max mode, to determine the shortest and longest distance, hold down the  button. To interrupt the continuous measurement, hold down the button.

Other functions

Addition (+) / Subtraction (-)
Single distance measurement

The next measurement is added to the previous one.
The next measurement is subtracted from the previous one.
The last step is undone.
(Hold down) the device switches off
Return to single distance measurement
Area measurement
Briefly press the button. The (area) symbol is shown in the display.
Press the button to measure the first distance (e.g., length)
Press the button to measure the second distance (e.g., width)
The result is automatically determined and shown in an m² format.
Volume measurement
Press the button 2x. The  (area) symbol is shown in the display.
Press the button to measure the first distance(e.g., length)
Press the button to measure the second distance(e.g., width)
Press the button to measure the third distance(e.g., height)
The result is automatically determined and shown in an m³ format.

Indirect measurement (Pythagoras)
– Determining a distance with two measurements
Indirect measuring is used to measure distances that cannot be measured directly because an obstacle would block the laser beam, or there is no suitable target surface as a reflector.
Indirect measurement for determining a distance with two auxiliary measurements.
Press the button until the symbol appears in the display. The distance to measure first is shown as a flashing line in the symbol.
Point to the top point and press the button.
After the first measurement, the first value is displayed.
Now level the laser measuring device horizontally to the extent possible.
Initiate the second measurement by pressing the button.
The result is automatically determined and shown in the display.

Indirect measurement 2 (double Pythagoras)
– Determining a distance with three measurements
Press the button 2x until the symbol appears in the display. The distance to measure first is shown as a flashing line in the symbol.
Point to the bottom point and press the button.
After the first measurement, the first value is displayed.
Now level the laser measuring device horizontally to the extent possible.
Initiate the second measurement by pressing the button.
Initiate the third measurement. Point to the top point and press the button.
The result is automatically determined and shown in the display.

History, archiving/internal memory

You can press the button to retrieve the last 10 measurements. To toggle between the measurements, press the and buttons.
Spirit level function
To hide the spirit level, hold down the button

Error signals/troubleshooting

operating temperature
101| Laser reception signal too weak| Use an alternative target
102| Reception signal of laser too strong| Reflections on the target surface. Use an alternative target. Reduce the distance
201| Ambient light is too bright| Use a measuring target in a darker environment
401| Hardware error| Switch the device off and back on. If the error message is still shown, contact our service hotline.

Servicing

The ProDist compact plus is a low-maintenance device.
However, you should follow these simple guidelines to ensure best possible performance.

1. Always handle the device carefully. It is an optical instrument with sensitive electronics.
2. Avoid exposing the device to shock, continuous vibration or extremely hot and cold temperatures.
3. Keep the device indoors at all times. When it is not
4.  in use, always keep the device in its protective holster.
5.  Keep the device away from dust and moisture. Only clean the device using a clean and soft cloth. If needed, use a gentle cleaning agent on the device’s surface only.
6.  Never touch the lens with your fingers.
7. Check the batteries regularly to avoid premature aging. If you will not be using the device for an extended period of time, always remove the batteries.
8. Replace the batteries when the battery charge message on the LCD display reads “empty”.
9.  Do not disassemble the device under any circumstances; doing so can expose the user to hazardous radiation.
10. Never attempt to modify any part of the laser lens.

Warranty

A legal warranty period of twelve months from the date of purchase/date of invoice applies to our tools for commercial customers. If we have granted an extended warranty period, this period will be noted separately in the operating manual for the equipment in question.

Claims
If you wish to claim under our warranty or guarantee, please return the complete device together with your invoice to our logistics center in Berka, postage paid. Before doing so, please contact your STORCH sales consultant.
Warranty entitlement
Claims can only be accepted for material defects or manufacturing errors, and only assuming proper use of the device. Wear parts (e.g. tools, sandpaper) are not covered by warranty. All claims shall become void in the event of installation of third party components, improper handling and storage, as well as in the event of obvious disregard of the operating instructions.
Disposal
If unused, dispose of together with domestic waste; if used, in accordance with the disposal regulations for the respective material.

Malerwerkzeuge & Profigeräte GmbH
Platz der Republik 6
42107 Wuppertal
Germany
Fon: + 49 202 49 20 1 12
Fax: + 49 202 49 20 1 1 1
info@storch.de
www.storch.de
shop.storch.de

References

• STORCH Malerwerkzeuge & Profigeräte GmbH

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>