STORCH 617100 WAMAB Turbowash pour ColorFree Top Instruction Manual

STORCH 617100 WAMAB Turbowash pour ColorFree Top

Contents of package

TurboWash with 1/2″ connection thread, connection hose with 1/2″ union nut, connection set for Wamab and ColorFree top with 4 x screws M 5 x 60 each, mounting sleeve, washer, O-ring*, 2 feet and assembly set for floor standing device 19 52 00. 61 71 00

Organization / Personnel

Operators

• Before starting to use the device the operator must have read and understood the operating manual.
• Only authorised and trained operators must have access to the device in order to operate it.
• The operating manual must be available to the operator at all times.
• The operator must not be under the influence of alcohol, drugs or medication.
• Children, performance-impaired persons, and pregnant women are not allowed to operate the device.

Applications and function
The paint roller cleaner is intended for cleaning paint rollers and for connection to the water tapping point or booster pump, Art. No. 61 70 75 for the ColorFree top splitting unit. The paint roller is driven by the water pressure and starts rotating. The washed-out paint and washing water is thrown off the roller by the rotation and runs out of the TurboWash at the bottom

Installation on the Wamab and  ColorFree top separating system

1. Slide the washer onto the mounting screws

2. Now insert the assembly screws from the outside through the holes on the rear wall of the wash basin and then slide the spacer sleeves from the inside of the sink onto the screws; next insert one o-ring each behind the spacer sleeve on each screw.

3. Now guide the Turbo-Wash onto the screws with the spacer sleeves and fix it in place with the screws in the threaded sleeves provided and tighten them evenly (3 mm Allen key).
   CAUTION: The ink roller must always be scraped out before the cleaning process and the material must be collected in the contai-ner. This saves time and water.

4. Connect the water tapping point or the booster pump and the Turbo-Wash using the connection hose provided.

5. Make sure that a flat gasket is inserted into each union nut of the connection hose.
   Now check whether the connections are tight by opening the water inlet, and opening and closing the ball valve of the Turbo-Wash. Now pay attention to the connection thread.

6. The Turbo-Wash Art. No. 19 52 00 is an upright unit; it is positioned in the respective wash basin and connected to the water dispensing point or the booster pump Art. No. 61 70 75.

• For Turbo-Wash Art. No. 61 71 00

  • Assembly kit for Wamab and ColorFree top
  • Installation on the Wamab
  • Installation on the Color-Free top
  • View of assembly kit wash basin side

CAUTION:

1. The Turbo-Wash is only designed for a maximum working pressure of 20 bar! Any other use or operation of the TurboWash than descri-bed in this manual is not permitted and may lead to mal-function and accidents.
2. To be on the safe side, always turn off the water cock of the water inlet after completion of the cleaning proce-dures.

Cleaning paint rollers

1. Before you guide the rollers into the Turbo-Wash, hold the roller over the paint container and scrape off as much of the paint as possible from the roller using a suitable tool.
2. Open the water cock of the water inlet.
3. Open the cover of the Turbo-Wash, insert the scraped out roller into the Turbo-Wash and close the cover again.
4. Now open the ball valve of the Turbo-Wash completely as far as it will go.
5. Move the paint roller up and down a little in order to achieve an equal cleaning. The best cleaning effect can be achieved when the water runs out of the edge of the roller and not in the middle so that the paint roller rotates at a higher speed.
   Then interrupt the water supply suddenly by shutting off the ball valve on the Turbo-Wash. The paint roller conti-nues to rotate at high speed and is immediately drier due to the centrifugal effect. Open the cover, remove the rol-ler from the Turbo-Wash and rinse the roller caps with the rinser head if necessary. Now turn the roller bow 180° and clean the roller again in the Turbo-Wash.

Replacement Parts

• 19 52 05 Nozzle distributor strip (without nozzles)
• 19 52 09 Sealing lips
• 19 52 13 Nozzle

Warranty

A legal warranty period of twelve months from the date of purchase/date of invoice applies to our tools for commercial customers.

Claims
If you wish to claim under our warranty or guarantee, please return the complete machine and your invoice to our logistics center in Berka, postage paid, or send it to one of our authorized service centres. We request that you contact us beforehand by calling our free STORCH service hotline on 0800 7 86 72 47.

Warranty entitlement
Claims can only be accepted for material defects or manufacturing errors, and only assuming proper use of the appli-ance. Wear parts are not covered by warranty claims. All claims shall become void in the event of installation of third party components, improper handling and storage, as well as in the event of obvious disregard of the operating instructions.

Performing repairs
All repairs must be conducted on our premises or by an authorized STORCH service centre.

Disposal
End-of-life devices must not be disposed of as domestic waste. Please take them to a suitable collection point or hand over the end-of-life device to your specialist dealer.

References

• STORCH Malerwerkzeuge & Profigeräte GmbH

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>