VEVOR PP13-1 Manual Strapping Tool User Manual

VEVOR PP13-1 Manual Strapping Tool

Other Modals

We continue to be committed to provide you tools with competitive price.
“Save Half”, “Half Price” or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and does not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you’re actually saving half in comparison with the top major brands.

• PP13-1, PP13-2

• XW19
  

• **P19

**

• GD-5
  
  

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificatewww.vevor.com/support

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation four user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform again there are any technology or software updates on our product.

Thank you very much for choosing this Manual Strapping Tool

• Please read all of the instructions before using it.The information will help you achieve the best possible results. The products carried in this catalog may be different in color than the actual item.

INSTRUCTIONS

WORK AREA

1. Operate in a safe work environment. Keep your work area clean, well-ligand free of distractions.

PERSONAL SAFETY

WARNING! Always Wear personal protective equipment.

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid personal injury or damage to tool.

1. Do not operate any tool when tired or under the influence of drugs,alcohol or medications.
2. 2. Avoid wearing clothes or jewelry that can become entangled with the moving parts of a tool. Keep long hair covered or bound.

SPECIFIC SAFETY PRECAUTIONS

1. Use the correct tool for the job. This tool was designed for a specific function. Do not modify or alter this tool or use it for an unintended purpose.
2. Keep body parts away from pinch areas while using.
3. Children are not allowed to operate this product unless accompanied by an adult
4. Become familiar with your tool and keep your fingers away from areas that can pinch or cut.
5. Never use strap as a means of pulling or lifting loads. Failure To Follow These warnings can result in severe personal injury.

MODEL AND PARAMETERS

PP13-1：

1. Strapping Tensioner ×1 PCS
2. Strapping Sealer Tool ×1 PCS
3. PP Plastic Strapping 330Ft(100m) Length×1/2inch(12.7mm) Width×1 PCS
4. Metal Seals ×100PCS

PP13-2：

1. Strapping Tensioner ×1PCS
2. Strapping Sealer Tool ×1PCS
3. PP Plastic Strapping 3300Ft(1000m) Length×1/2inch(12.7mm)Width×1PCS
4. Metal Seals ×1000PCS

P19:

1. Strapping Tensioner ×1PCS
2. Strapping Sealer Tool ×1PCS
3. PET Strapping 1000Ft(300m)Length×5/8inch(15.8mm)Width ×1PCS
4.  Metal Seals ×300PCS

XW19:

1. Strapping Tensioner ×1PCS
2. Woven Cord Strapping 330Ft(100m) Length×3/4 inch (19mm)Width ×1
3. Metal Buckles ×100PCS

GD-5:

1. Strapping Tensioner ×1
2. Stainless steel tape 100Ft(30m) Length×3/4inch(19mm)Width ×1
3. Stainless steel clasp ×100PCS

ASSEMBLY AND USE

PP13-1\ PP13-2\P19 instructions

1. Strapping tensioner see FIG. 1, Press the tension bar and load strapping,L≥3inch(8cm).
   

2. Put packed the strapping slips into the cutter trough and the capstan trough,see FIG. 2 .

3. Operate this tension bar repeatedly from FIG. 2 to FIG.3 ,the strapping will be tightened.
   

4. Clamp the metal Seals with the strapping sealer tool, as shown in Fig 4.
   

5. Press the tension bar，the strapping will be cut.
   

XW19 instructions

1. As shown in the FIG.5, Preinstall the strapping to use two metal seals, the operation of Strapping Tensioner, refer to the PP13.
   

GD-5 instructions

1. Stainless steel tape for cutting(length equal to circumference + 5.9-7.8inches / 15-20cm)|

---|---
2. Put the stainless steel clasp on the stainless steel tape 2 inches(5 cm )from the edge,ears up.Bend the end of the stainless steel tape down and place it under the buckle.|

3. Wrap the stainless steel tape around the buckle and pass the free end of the tape through the buckle.|
4. Place the tape in the guide slot of the tensioner ,swing the retracting handle up and down to tighten the tape to the desired tension level.Push the tool pliers for ward to bend the tape to one side of the buckle,and then cut the stainless steel tape with the operation cutting

handle.

|

---|---
5.Use a hammer to screw the end of the tape between the two ears of the buckle,and then screw the ears of the buckle over the steel tape to keep the tape in the tight position.|

MAINTENANCE

1. Avoid prolonged exposure to the sun to avoid aging.

Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai
Imported to AUS: SIHAO PTY LTD.1 ROKEVA STREET EASTWOOD NSW 2122 Australia
Imported to USA: Sanven Technology Ltd.Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

SHUNSHUN GmbH
 Römeräcker 9 Z2021, 76351
Linkenheim-Hochstetten, Germany

Pooledas Group Ltd
 Unit 5 Albert Edward House, The
Pavilions Preston, United Kingdom

Customer Support

Technical Support and E-Warranty Certificate www.vevor.com/support

Teknisk support och e-garanti certifikat www.vevor.com/support

References

• Contact Us – Official VEVOR Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>