MONDAWE 2048 Widespread Bathroom Sink Faucet Instruction Manual

MONDAWE 2048 Widespread Bathroom Sink Faucet

Other Models

• Model:2048
  

• Model:DM-LT23
  

Installation Condition

1. Refer to the (( Standard Part List>) when unpacking , check all parts available .

2. Do not disassemble mixer body by yourself.
   

3. Connect inlet hoses to supply valves.

4. Make sure inlet pipes and supply valves have been installed and cleaned, also ensure no impurities in pipeline.
   

5. After installation , check all joints for leakages.

6. Suggest don’t fit the faucet in the severely corrosive environments.

Basin Faucet Standard Part List

Hose Connection Travel

Basin Faucet lnstallation

1. Faucet Body 1 through the basin hole. Install Faucet Body Gasket 4 and Mounting Nut 5 in sequence and tighten the nut with a wrench. Press and hold the button on the 9 Connect hose head to connect to the body fitting.
   

2. Remove the Handle 3 and put them on the basin holes .Connect the Control Water Bodies 8 with 3 Handle and 2 Handle rod from the underside of the basin holes,. Finally install the~ Handle rod and use Screws tighten them.(Not to disassembled the valve by yourself. otherwise leakage will occur. )
   

3. Connect one side of the inlet 9 connect hoses to the 8 Control Water Bodies.
   

4. Separately connect another two inlet hoses to ang le valves and control water bodies , left connect to the hot water, right connect to cold water.
   

Bathtub Faucet Standard Part List

Hose Connection Travel

Bathtub Faucet Installation

1. Faucet Body 1 through the basin hole. In stall Faucet Body Gasket 2 and Mounting Nut 4 in sequence and tighten the nut with a wrench. Press and hold the button on the 18 Connect hose head to connect to the body fitting.
   

2. Remove the handle 10 and put them on the bathtub holes Connect Transforms Control Valve 11 and Control Water Bodies 11 with Decorate Seats 10 from the underside of the bathtub holes , and tighten them . Then install the Handles 10 and tighten them. Hand Pedestal 6 instar illation : Remove Pedestal l Gaskets (J) and Mounting Note 8. Connect them with Hand Pedestal 6 from the underside of the bathtub holes, and tighten Mounting Nut 8 with a wrench. (otherwise leakage will occur. Left Control Water Body 13 connects to the hot water, right connects to cold water.)
   

3. Install Hot and Cold Hoses 13 as the above drawings. Connect one side of Hot and Cold Hoses 13 with Transforms Control Valve 11 , the other side to Control Water Bodies 12. Left is to hot water, right is to cold water. One side of Shower Hose 15 is connected to Hand Shower 5 , the other side is connected to the Shower Connect Hose 14 through Hand Pedestal 6 Then the other side of Shower Connect Hose 18 is connected to Transforms Control Valve 11. Finally one side of Body Connect Hose  14 is connected with Facet body 1 ,the other side is connected to Transforms Control Valve 1 , and tighten them Separately connect another two in let hoses to angle valves and Control Water Bodies 12.
   
   Adjust the handwheel installation position according to your own preference
   

Basin Faucet Application Instruction

1. Operating handle gradually is better for valve protection
   

2. The handles turn right or left is to open or close. The larger the rotation angle, the larger the flow rate. Conversely, the smaller the rotation angle, the smaller the flow rate. Mixed warm water when the cold water handle and the hot water handle are opened at the same time.
   

Bathtub Faucet Application Instruction

1. The middle one of the Handles 9 is control water diversion of the Faucet Body 1 and Hand Shower 5.Turn left ,water comes out from the Hand Shower 5;turn right .water comes out from the Faucet Body 1.
2. 0perating handle gradually is better valve protection.
3. The handles 9 turn right or left is to open or close. The larger the rotation angle, the larger the flow rate. Conversely, the smaller the rotation angle, the smaller the flow rate. Mixed warm water when the cold water handle and the hot water handle are opened at the same time.
4. Turn on the water supply, check all connect points if leaking. If leaking, tighten it. Now the faucet is ready for using.
   

CARE AND MAINTENANCE

In order to keep the mixer surface bright , please clean the mixer regularly.

Rinse faucet with clean water and wipe with soft cotton cloth. Avoid suing cleaning powder , harsh cleaning chemicals, brushes. and cloth with coarse surface to prevent scratching and corrosion.

Do not use acid cleaner to clean the faucet as it may cause surface corrosion of the faucet. If the faucet comes into contact with harmful acid substances, please rinse it with water immediately.

IF A LARGE-SCALE CLEAN-UP IS NECESSARY, FOLLOW THESE PROCEDURES

1. Use clean water and soft cloth to remove dirt on the surface as much as possible.

2. Use one of the following cleaners to remove dirt on the surface Mild liquid cleaner.
   Colorless glass cleaner, powder cleaner which does not have abrasive function and can be dissolved completely. Polish liquid which does not abrasive function .

3. After cleaning , remove the cleansing agent with clean water completely and wipe with soft cotton cloth.

Customer Support

After-sales contact
Email: [email protected]
TEL: 303-747-4321

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>