MONDAWE D-3.3YF Wall Mounted Rain Shower System Instruction Manual
- June 17, 2024
- Mondawe
Table of Contents
Instruction Manual
Rain Shower System
D-3.3 (YF)
Installation Condition
| 
---|---
- Check the accessories list to verify that all parts are complete in this package.
- Do not disassemble the main body by yourself.
- Connect inlet pipes to supply valves.
- Make sure inlet pipes and supply valves have no Impurities and are cleaned, with no impurities in the pipeline.
- After installation, check all joints for leakages.
- Do not leave the rain shower system exposed to a severely corrosive environment.
YOU MAY NEED:
Two-function Rain Shower System
Model: A
Accessories List
| No. | Part name | Qty | No. | Part name | Qty |
|---|---|---|---|---|---|
| 1 | Shower head | 1 | 11 | Main body | 1 |
| 2 | Shower arm | 1 | 12 | Water diverter screw | 1 |
| 3 | Shower arm cup | 1 | 13 | Water diverter cap | 1 |
| 4 | Hand shower holder | 1 | 14 | Handle screw | 1 |
| 5 | Holder cup | 1 | 15 | Handle cap | 1 |
| 6 | Hand shower | 1 | 16 | Main body spare parts | 4 |
| 7 | Shower hose | 1 | 17 | Instruction manual | 1 |
| 8 | Water diverter | 1 | 18 | Gloves | 2 |
| 9 | Handle | 1 | 19 | Handle parts | l set |
| 10 | Deck plate | 1 |
Essential dimensions & water pipe line
The installation depth of shower holder and body jet
The thickness of the tile must be calculated for installation.
Connector size of male thread: USA: 1/2″-14NPT, Canada: 1/2″-14NPT, Europe:
G1/2″.
Model: B
Accessories List
| No. | Part name | Qty | No. | Part name | Qty |
|---|---|---|---|---|---|
| 1 | Shower head | 1 | 11 | Main body | 1 |
| 2 | Shower arm | 1 | 12 | Water diverter screw | 1 |
| 3 | Shower arm cup | 1 | 13 | Water diverter cap | 1 |
| 4 | Hand shower holder | 1 | 14 | Handle screw | 1 |
| 5 | Holder cup | 1 | 15 | Handle cap | 1 |
| 6 | Hand shower | 1 | 16 | Main body spare parts | 4 |
| 7 | Shower hose | 1 | 17 | Instruction manual | 1 |
| 8 | Water diverter | 1 | 18 | Gloves | 2 |
| 9 | Handle | 1 | 19 | Handle parts | l set |
| 10 | Deck plate | 1 |
Essential dimensions & water pipe line
The installation depth of shower holder and body jet
The thickness of the tile must be calculated for installation.
Connector size of male thread: USA: 1/2″-14NPT, Canada: 1/2″-14NPT, Europe:
G1/2″.
Installation Depth Of Main Body(Model : A &B)
Notice:
- The installation depth of the main body should be no less than 2 9/16″ (65mm) and no more than 2 15/16″ (75mm), including the thickness of the tile. Otherwise, the deck plate cannot be installed.
- The opening size of ceramic tile shall be smaller than the deck plate size.
Piping Instructions Before Tiling(Model : A &B)
As shown in the figure, the inlet and outlet pipes are pre-buried. Please pay attention to the correct direction when installing the pre-buried main body.- Before tiling, turn on the water to test whether the left and right inlet pipes are tightly connected without leakage.
Then, adjust the flow switch to the “on” position to check for leaks in the mixed outlet pipes.
Main Body Valve Installation(Model : A &B)
Make marks according to the size of the main body valve, and then drill anchors into the wall (concrete wall).- Lock the main body to wood directly with screws (wood wall).
- When installing the main body, please mark the UP side up and do not install it upside down.
▲ Please note that the level meter should be parallel to the wall; otherwise, the deck plate cannot be installed.
Installation of the Hand Shower Holder (Model: A &B&C)
Connect shower arm with the cover before screwing arm into riser connection to prevent damage.- Fix shower head onto shower arm and apply tape to pipe threads on both ends.
- Do not overtighten shower head. It is 360° swivel connection.
Model: C
Accessories List
| No. | Part name | Qty | No. | Part name | Qty |
|---|---|---|---|---|---|
| 1 | Shower head | 1 | 10 | Deck plate | 1 |
| 2 | Shower arm | 1 | 11 | Main body | 1 |
| 3 | Shower arm cup | 1 | 12 | Water diverter screw | 1 |
| 4 | Hand shower holder | 1 | 13 | Handle screw | 1 |
| 5 | Holder cup | 1 | 14 | Handle cap | 1 |
| 6 | Hand shower | 1 | 15 | Main body spare parts | 4 |
| 7 | Shower hose | 1 | 16 | Instruction manual | 1 |
| 8 | Water diverter | 1 | 17 | Gloves | 2 |
| 9 | Handle | 1 | 18 | Handle parts | l set |
Essential dimensions & water pipe line
The installation depth of shower holder and body jet
The
thickness of the tile must be calculated for installation.
Notice:
- The installation depth of the main body should be no less than 2 9/16″ (65mm) and no more than 2 15/16″ (75mm), including the thickness of the tile. Otherwise, the deck plate cannot be installed.
- The opening size of ceramic tile shall be smaller than the deck plate size.
Piping Instructions Before Tiling
As shown in the figure, the inlet and outlet pipes are pre-buried. Please pay attention to the correct direction when installing the pre-buried main body.- Before tiling, turn on the water to test whether the left and right inlet pipes are tightly connected without leakage.
Then, adjust the flow switch to the “on” position to check for leaks in the mixed outlet pipes.
Main Body Valve Installation
Make marks according to the size of the main body valve, and then drill anchors into the wall (concrete wall).- Lock the main body to wood directly with screws (wood wall).
- When installing the main body, please mark the UP side up and do not install it upside down.
▲ Please note that the level meter should be parallel to the wall; otherwise, the deck plate cannot be installed.
Installation of the Hand Shower Holder (Model: A &B&C)
Connect shower arm with the cover before screwing arm into riser connection to prevent damage.- Fix shower head onto shower arm and apply tape to pipe threads on both ends.
- Do not overtighten shower head. It is 360° swivel connection.
Installation The Hand Show Holder(Model: A &B&C)
Step1.
Screw the thread into the water pipe inside the wall
Step2. Screw the main body into the thread.
Step3. Rotate and fix the body with the special-shaped wrench
Step4. Connect hand shower and the hose.
Do’s
| 
---|---
- In order to keep the mixer surface bright, please clean the mixer regularly.
- Rinse the faucet with clean water and wipe it with a soft cotton cloth.
- Use one of the following cleaners to remove dirt from the surface
a. Mild liquid cleaner.
b. Colorless glass cleaner and powder cleaner that do not cause abrasion and can be dissolved completely.
c. Polish liquid that does not cause abrasion.
Don’ts
a. Avoid using cleaning powder, harsh cleaning chemicals, brushes and coarse
cloth to prevent scratching and friction.
b. Do not use acid cleaners to clean the faucet as they may cause surface
corrosion of the faucet. If the faucet is exposed to harmful acid substances,
please rinse it immediately with water. ****
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>