MONDAWE 6374 Bathroom LED Shower System Installation Guide

June 17, 2024
Mondawe

THERMOSTATIC SHOWER Series

INSTALLATION GUIDE

Model : 6374                      Model : 6374-B

B-8

INSTALLATION CONDITION
  1. Refer to the « Standard Part List » when unpacking, check all parts available.
  2. Do not disassemble mixer body by yourself.
  3. Connect inlet hoses to supply valves.
  4. Make sure inlet pipes and supply valves have been installed and cleaned, also ensure no impurities in pipeline.
  5. After installation, check all joints for leakages.
  6. Suggest don’t fit the faucet in the severely corrosive environments.

YOU MAY NEED:

Model:6374 PRODUCT LIST

MONDAWE 6374 Bathroom LED Shower System - c1

a) Or Ceiling Shower arm
b) Model:6374-B

MONDAWE 6374 Bathroom LED Shower System - c3

No.

| Part name| Qty
---|---|---

1

| Shower head|

1

2

| Shower arm|

1

3

| Shower arm cup|

1

4

| Shower hand|

1

5

| Hand show holer|

1

6

| Holder parts|

1

7

| Shower hose|

1

8

| Main body|

1

9

| Panel|

1

10

| Water diverter rod|

3

11

| Water diverter|

3

12

| Handle|

1

13

| Body jet cup|

6

14

| Body jet|

6

15

| Cup|

1

16

| Connector|

1

17

| Valve gasket spare parts|

6

18

| Handle cup|

1

19

| Screw|

1

20

| Wrench|

1

21

| Instruction manual|

1

22

| Gloves|

2

INSTALLATION SHOWER SET SIZE & WATER PIPE LINE REFERENCE

Unit: mm/inch

MONDAWE 6374 Bathroom LED Shower System - d1

  1. Over Head shower

  2. 5 33/64″~6 19/64″
    (140-160mm)

  3. Hand shower

  4. 11 13/16″ 15 17/64″
    (300-400mm)

  5. 47 1/4″~59″
    (1200-1500mm)

  6. 43 5/16″~51 3/16″
    (1100-1300mm)

  7. connector

  8. 7 7/8″~9 13/16″
    (200-250mm)

  9. HOT
    Hot water inlet

  10. COLD
    Cold water inlet

  11. Finish surface

  12. Please refer to above for height dimensions of shower installation.

INSTALLATION DEPTH OF SHOWER ARM &SHOWER HOLDER & BODY JET

Unit: mm/inch

MONDAWE 6374 Bathroom LED Shower System - d2

  1. USA: 1/2″-14 NPT
    Canada: 1/2″-14 NPT
    Europe: G1/2″

  2. The installation depth of shower arm &shower holder &body jet & connector can’t over 19/32″(15mm) so the thickness of tile must be calculated before installation.

  3. 15mm
    19/32″

  4. connector

  5. body jet

  6. Face of plaster guard should be flush with finish wall line

  7. Main body

  8. Tile wall

  9. shower arm

INSTALLATION DEPTH OF MAIN BODY

Unit: mm/inch

  1. 326mm/12 13/16″

  2. 75mm
    2 15/16″

  3. 130mm
    5 1/8″

  4. 382mm
    15″

  5. 3 1/8″min
    80mm

  6. Tile wall

  7. Depth

  8. 95mm
    3 3/4″max

The depth of main body should be in the thickness range of wall tile

1: Including the thickness of ceramic tile is less than or equal to the thickness of valve 3 3/4″ (95mm), so the thickness of tile must be calculated before installation.
2: Installation Main body depth not less than 3 1/8″(80mm)min and not more than 3 3/4″ (95mm) Max, Otherwise, the panel cannot be installed.


WALL MOUNTED/CELILING MOUNTED INSTALLATION BEFORE TILONG

MONDAWE 6374 Bathroom LED Shower System - d6

  1. Recommend using copper drop ear pipe elbow(NPT 1/2″)

1: Recommend using Copper drop ear pipe elbow(NPT 1/2)
USA:1/14 NPT 2 -Canada:1/2″-14 NPT Europe:G1/2″

MAIN BODY CONNECTING PIPE SCHEMATIC DIAGRAM

Warning: must install hot water and cold water inlet strictly as instructions.

MONDAWE 6374 Bathroom LED Shower System - d7

  1. Wrap enough teflon tape

  2. Level

  3. Mixed water outlet pipe

  4. USA: 1/2″-14 NPT
    Canada: 1/2″-14 NPT
    Europe: G1/2″

  5. Cold water pipe

  6. Hot water pipe

1. As shown in the figure, the inlet and outlet pipes are pre-buried, pay attention to the correct direction of installing the pre-buried main body, and make sure that the mark level on the top of the installation box is facing upward.
2. Install the hot and cold water inlet pipes, Shower head and hand shower holder body jet pipes. Turn on the water source to test whether the left and right inlet pipes are tightly connected without leakage. After the test, adjust the flow switch to be on to test whether the mixed outlet pipe. The connection is tight and there is no leakage.


MAIN BODY VALVE INSTALLATION

Use (17) Valve gasket spare parts and to fixed (8) Main body on the wall and then install (9) Panel (12) Hand (18) Hand cup and Hand screw (11) Water diverterl (10) Water diverted rod in the correct order.

INSTALLATION OF MASSAGE SHOWER
  1. USA: 1/2″-14 NPT
    Canada: 1/2″-14 NPT
    Europe: G1/2″

Step 1. Wrap the threaded pipe of NPT1/2 with Teflon tape and screw it into the wall.
Step2. Cut off excess part with a saw.
Step3. Put on the decoration cap, then screw the massage shower in.


SHOWER HOLDER INSTALLATION INSTALL THE HAND SHOW HOLDER
  1. copper fittings
  2. Waterproof rubber pad

1.The connector to be wrapped with teflon tape, Screw the thread into the water pipe inside the wall.
2.Install the rubber pad on the shower hose and connect it with the connector.
3.Using anchors to screw the copper fittings to the wall firstly
4.Remove two screws on the shower seat
5.Insert the shower seat into the copper fittings that have been installed on the wall and then fix the shower seat with 2 screws

INSTALLATION OF RAIN SHOWER HEAD& SHOWER ARM

Female thread elbow

Connect top outlet (1) to shower arm (2) with proper fittings. To prevent damage, to finish on shower arm, insert wall end of shower arm into shower flange (3) 6before screwing arm into riser connection. Thread showerhead (4) onto shower arm. Apply tape to pipe threads on both ends. Do not overtighten showerhead. The showerhead is 360 swivel connection.

Female thread elbow

Connect top outlet (5) to shower arm (7) with proper fittings. To prevent damage, to finish on shower arm, insert wall end of shower arm into shower flange (6) before screwing arm into riser connection. Thread showerhead (8) onto shower arm. Apply tape to pipe threads on both ends. Do not overtighten showerhead. The showerhead is 360° swivel connection.

Do’s

  1. In order to keep the mixer surface bright, please clean the mixer regularly.
  2. Rinse the faucet with clean water and wipe it with a soft cotton cloth.
  3. Use one of the following cleaners to remove dirt from the surface:
    a. Mild liquid cleaner.
    MONDAWE 6374 Bathroom LED Shower System - f2b. Colorless glass cleaner and powder cleaner that do not cause abrasion and can be dissolved completely.
    c. Polish liquid that does not cause abrasion.

Don’ts

a. Avoid using cleaning powder, harsh cleaning chemicals, brushes and coarse cloth to prevent scratching and friction.
b. Do not use acid cleaners to clean the faucet as they may cause surface corrosion of the faucet. If the faucet is exposed to harmful acid substances, please rinse it immediately with water.

Website: www.mondawe.com
Customer Service: service@mondawe.com
Phone: 888-328-5111

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Mondawe User Manuals

Related Manuals