BAMBU LAB PF002-A Combo Plus 4kg PLA User Guide

BAMBU LAB PF002-A Combo Plus 4kg PLA

Specifications:

• Model: Bambu Lab A1
• Product Code: PF002-A
• Printing Technology: Fused Filament Fabrication (FFF)
• Build Volume: 200mm x 200mm x 200mm
• Layer Resolution: 0.1mm – 0.4mm
• Max Nozzle Temperature: 260°C
• Max Heatbed Temperature: 100°C

Product Usage Instructions

1. Install Build Plate:

   • Base Housing: Install the build plate with the correct orientation, aligning the edge with the heat bed.

2. Mate Base Housing & Printer Frame:

   • Printer Frame & Base Housing: Follow the steps provided in the manual to properly align and connect the Printer Frame and Base Housing.

3. Unlock Toolhead:
   Remove any packaging materials and securely unlock the tool head following the instructions provided.

4. Remove Y-Axis Cover:
   Open the Y-axis cover as instructed and gently remove it to access the internal components.

5. Plug In Cable Box:
   Properly align and plug in the cable box connectors, ensuring a secure connection with the Base Housing.

6. Powering On:
   Plug in the power cable and turn on the printer using the power switch. Allow space for heat bed movement as indicated.

7. Network Setting:
   Follow the on-screen instructions to set up the network connection for your printer.

Frequently Asked Questions (FAQ):

• Q: What should I do if the printer does not power on?
  A: Check the power cable connection and ensure it is securely plugged in. Verify that the power switch is in the ‘on’ position.

• Q: How do I troubleshoot filament jamming issues?
  A: Refer to the user manual for instructions on how to unclog the nozzle using the provided Unclogging Pin Tool.

• Q: Can I use third-party filaments with this printer?
  A: It is recommended to use filaments provided by the manufacturer to ensure optimal print quality and compatibility.

Please review the entire guide before operating the printer.

• Safety Notice: Do not connect to power until assembly is complete.

What’s In The Box

Accessory Box

Install Build Plate

1. Install the build plate with correct orientation, aligning the edge with the heatbed.

Unlock Heatbed

1. Flip the base housing 90 degree to the side opposite to the screen.
2. Use Allen Key H2 to remove the 4 highlighted screws at the bottom of the Base Housing to unlock the heated (Be careful when fully releasing the heatbed; use foam padding in the package to protect the heatbed from swinging).

Mate Base Housing & Printer Frame

1. Put the Printer Frame on the table as shown above.
2. Tilt the Base Housing about 45 degrees to pass through the Printer Frame. (Use the screen as an indicator for orientation)
3. Align the slot with the Printer Frame as shown in the diagram.
4. Slowly lower the Base Housing until it is fully flush with the Printer Frame on the table.

Unlock Toolhead

1. Cut the zip-tie and cardboard wrapped around the tool head and X-axis.
2. Remove the 7zipties and 2foam paddings on the printer frame.

Remove Y-Axis Cover

1. Push the heatbed fully to the front end, where the screen is located.
2. Open the Y-axis cover.
3. Pull out the Y-axis cover gently.

Lock Base Housing

1. Install 10*ST3-23 Screws (For Base Housing) in the holes highlighted in green.
2. Push the heatbed to the other end.

Lock Base Housing

1. Install 2*ST3-23 Screws (For Base Housing) in the holes highlighted in green.

Put Cover Back

1. Push the heatbed fully to the front end, where the screen is located.
2. Gently slide the Y-axis cover back into place.
3. Make sure to align the clip.

Place On Table

1. Turn the A1 90 degree onto its rear, laying it on the edge of a table. (It is recommended to cover the table with cardboard for protection.) Please make sure the printer is secure on the table while following the steps.

Plug In Cable Box

1. Align the 2 clips on the cable box with the holes on the Base Housing.
2. Slide up the cable box until the Type-C cable clicks in place. (DO NOT force the insert.)
3. Make sure the cable box is nice and flush in the slot, then screw in the pre-installed screw highlighted in green.

Plug In Connectors

1. Plug in the 3 harnesses according to color.
2. Tuck the harness into the cable slot and then close the cover.

Fold Out Touch Screen

1. Fold out the touch screen. Make sure the touch screen is in place as shown in the graph.

Install Purge Wiper

1. Slide in Purge Wiper unit into the slot at the end of the X-axis.
2. Install the 1*M3-12 screw from the accessory box to fix the Purge Wiper in place.

Powering On

1. Plug in the power cable and turn on the A1 using the power switch on the back.

Please leave a safe amount of space for heatbed movement (as shown in the diagram).

Network Setting

1. Follow the instructions untill you see this screen. Press “Select Wi-Fi” to search for available network.
2. Select your preferred network.
3. Input the passcode, and then press “OK”.

Printer Binding

1. Download the Bambu Handy App. Register and log in to your Bambu Lab account.
2. Use Bambu Handy to scan the QR code on the screen, and bind your printer to your Bambu Lab account.
3. Follow the instructions on the screen to complete the initial calibration. It is normal to have vibration and noise during the calibration process.

External Spool (for non-AMS use case)

1. Assemble the spool holder.
2. Connect the tool head filament inlet (either one of four) and the filament guide with the 600mm PTFE tube as shown in the diagram.
3. Install the cable organizer as shown in the graph.
4. Hang filament spool on the spool holder then feed the filament line into the PTFE tube as shown in the diagram.

First Print

1. Press “Print Files” to access the preloaded models on the SD card.
2. Select the model you want to print.
3. Turn on “Use AMS” if you are using filaments on AMS.
   • Turning on “Bed leveling” is recommended.
   • Turn on “Timelapse” for timelapse video recording.

Specification

Toolhead

| Hot End| All-Metal
Extruder Gears| Hardened Steel
Nozzle| Stainless Steel
Max Hot End Temperature| 300 ℃
Nozzle Diameter (Included)| 0.4 mm
Nozzle Diameter (Optional)| 0.2 mm, 0.6 mm, 0.8 mm
Filament Cutter| Yes
Filament Diameter| 1.75 mm

Heatbed

|

Compatible Build Plate

| Bambu Textured PEI Plate Bambu Smooth PEI Plate Bambu Cool Plate
Max Build Plate Temperature| 100 ℃

Speed

| Max Speed of Tool Head| 500 mm/s
Max Acceleration of Tool Head| 10000 mm/s²

Max Hot End Flow

| 28 mm³/s @ABS (Model: 150*150 mm single wall; Material: Bambu ABS; Temperature: 280 ℃)
Cooling| Part Cooling Fan| Closed Loop Control
Hot End Fan| Closed Loop Control

Supported Filament

| PLA, PETG, TPU, PVA| Ideal
ABS, ASA, PC, PA, PET,

Carbon/Glass Fiber Reinforced Polymer

| Not Recommended

Sensors

| Monitoring Camera| Low Rate Camera (up to1080P) Timelapse Supported
Filament Run Out Sensor| Yes
Filament Odometry| Yes
Power Loss Recover| Yes
Filament Tangle Sensor| Yes
Physical Dimensions| Dimensions (W×D×H)| 465410430 mm³
Net Weight| 8.3 kg

Electrical Parameters

| Input Voltage| 100-240 VAC, 50/60 Hz
---|---|---
Max Power| 1300W@220V, 350W@110V

Electronics

| Display| 3.5 inches 320*240 IPS Touch Screen
Connectivity| Wi-Fi, Bambu-Bus
Storage| Micro SD Card
Control Interface| Touch Screen, APP, PC Application
Motion Controller| Dual-Core Cortex M4

Software

|

Slicer

| Bambu Studio

Support third party slicers which export standard Gcode such as SuperSlicer, PrusaSlicer and Cura,

but certain advanced features may not be supported.

Slicer Supported OS| macOS, Windows

Wi-Fi

|

Frequency Range

| 2412 MHz – 2472 MHz (CE)

2412 MHz – 2462 MHz (FCC)

2400 MHz – 2483.5 MHz (SRRC)

Transmitter Power (EIRP)| ≤ 21.5 dBm (FCC)

≤ 20 dBm (CE/SRRC)

Protocol| IEEE 802.11 b/g/n

Bambu Studio Bambu Handy
https://bambulab.com/download.

References

• Bambu Lab | Unleash Your Creativity with Bambu Lab 3D Printers - Bambu Lab

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>