Bambu Lab SA001 AMS Color 3D Printer Instructions

June 5, 2024
Bambu Lab

SA001 AMS Color 3D Printer
Instructions

Bambu Lab SA001 AMS Color 3D Printer

Bambu Lab SA001 AMS Color 3D Printer - 1

Place at least one spool of Bambu Filament into the AMS. Turn on the power to start the printer and the AMS. Insert the filament into the filament inlet. The filament will be automatically pre-loaded when detected.

Enjoy!

If you run into any issues during the guided setup, we are here to help.
customersupport@bambulab.com 
www.bambulab.com

Disclaimer and Safety Guidelines

Disclaimer and Warning

Thanks for purchasing a Bambu Lab product. The information in this document affects your safety and your legal rights and responsibilities. Read this entire document carefully to ensure proper configuration before use. Failure to read and follow instructions and warnings in this document may result in serious injury to yourself or others, damage to your Bambu Lab product, or damage to other objects in the vicinity. This document and other collateral documents are subject to change at the sole discretion of Bambu Lab. By using this product, you hereby signify that you have read this disclaimer and warning carefully and that you understand and agree you are solely responsible for your own conduct while using this product, and for any consequences thereof. You agree to use this product only for purposes that are proper and in accordance with all applicable laws, rules, and regulations, and all terms, and precautions. practices, policies, and guidelines Bambu Lab has made and may make available. Bambu Lab accepts no liability for damage, injury, or any legal responsibility incurred directly or indirectly from the use of the product. The user shall observe safe and lawful practices including, but not limited to, those set forth in this document.
Bambu lab is a trademark of Shenzhen Tuozhu Technology Co., Ltd. and its affiliated companies. Names of products, brands, etc., appearing in this manual are trademarks or registered trademarks of their respective owner companies.

Before You Start

The following documents have been produced to help you safely operate and make full use of your Bambu Lab AMS:
Bambu Lab AMS Disclaimer and Safety Guidelines
Bambu Lab AMS Quick Start Guide
Check that you have all the included parts. Please review the entire Quick Start Guide before operating the AMS. Read the Disclaimer and Warning above to understand your legal rights and responsibilities. If you have any questions or problems during the installation, maintenance, or use of this product, please contact a Bambu Lab authorized dealer.

Safety Guidelines

  1.  The product must be disconnected from the power supply before carrying out any installation or maintenance work.
  2. Installation and maintenance must be carried out by a skilled worker in compliance with the manufacturer’s instructions and local safety regulations.
  3. Do not use multiple plug adapters or extension leads.
  4. Do not touch the product with any wet part of the body and do not operate it while barefoot.
  5. Do not reach inside the appliance while it is in operation.
  6. Children using or near the printer must be accompanied and supervised by a responsible adult at all times.
  7. This product is designed solely for indoor use. It should be kept in a dry environment.
  8. The recommended operating temperature for the appliance is between 0°C to 40°C (32°F to 104°F).
  9. The recommended humidity level is under 85%.
  10. The product should be positioned on a clean, stable, and flat workbench.
  11. , The product should be kept in a well-ventilated location.

Compliance Information

FCC Compliance Notice
Supplier’s Declaration of Conformity Product name: AMS Model Number: SA001 Responsibility Party. Shenzhen Tuozhu Technology CoLtd. (Bambulab USA Inc) Responsibility Party Address: 8000 Centre Park Drive, STE 330, Austin, TX, 78754 Website: www.bambulab.com

We, Shenzhen Tuozhu Technology Co., Ltd. (Bambulab USA Inc), being the responsible party, declares that the above-mentioned model was tested to demonstrate compliance with all applicable FCC rules and regulations.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body.
ISED Compliance Notice This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

EU Compliance Statement

Hereby, Shenzhen Tuozhu Technology Co., Ltd. declares that the radio equipment type Bambu Lab AMS is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.bambulab.com/euro-compliance

GB Compliance Statement

Hereby, Shenzhen Tuozhu Technology Co., Ltd. declares that the radio equipment type Bambu Lab AMS is in compliance with Radio Equipment Regulations 2017. The full text of the GB declaration of conformity is available at the following internet address: www.bambulab.com/euro-compliance

Bambu Lab SA001 AMS Color 3D Printer - icon
www.bambulab.com Copyright © 2022 Bambu Lab All Rights Reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals