Bambu Lab A00201 P1S 3D Printer User Manual

3D Printer
Quick Start

Please review the entire guide before operating the printer.
Safety Notice : Do not connect to power until assembly is complete.

Bambu Studio & Bambu Handy
https://www.bambulab.com/download

Component Introduction

Accessory Specification

Tool Head Unlock

Remove the carboard from the tool head. Romove the foam from the excess chute.

Cut the zip tie securing the toolhead.

Spool Holder Assembly

Remove the screws as pictured with an Allen Key H2.
Attention: Please use the short end of the Allen Key to unlock the screws.

Secure the spool holder with two screws from the accessory box.

Hot Bed Unlock & Screen Installation

Remove the three screws with an Allen Key H2 to unlock the hot bed.

Insert the LCD cable into the port by plugging it into the terminal as pictured.

Attention: Bend the LCD cable towards the opening on the back of the screen as pictured.

Inset the screen back to the slot on the printer, then lock it by pushing it to the left.

Printer Binding

1. Download the Bambu Handy App. Register and log in to your Bambu Lab account.
2. Connect the printer to power. Follow the instructions on the screen until getting to the page shown on the right side. QR Code

https://bambulab.com/en/download/app

3.  Use Bambu Handy to scan the QR code on the screen, and bind your printer with your Bambu Lab account.
   

4. Follow the instructions on the screen to complete the initial calibration.
   DO NOT remove the protective foam from beneath the hot bed until after the initial calibration is complete.
   It is normal to have vibration and noise during the calibration process.

First Print

Insert filament into the PTFE Tube. Keep pushing the filament until it can not move forward.

• We recommend using the supplied Bambu PLA for your first test print.

Select “ ” and select a file to start the first print.
*We recommend using one of the pre-loaded files as a first test print. All the pre-loaded files can be printed with PLA Basic or PLA Matte.

Select ”   “-“ “, and heat the nozzle to the recommended temperature for the filament. Select “ “-“E”-“ ” several times until the filament comes out from the nozzle and cannot be pulled out from the PTFE tube anchor manually.

Bambu Studio

Download Bambu Studio: https://bambulab.com/en/download/studio

Log in to Bambu Studio with your Bambu Lab account, which is the same for the Bambu Online store.
Create or open a project.

During printing, you can remotely monitor your print, or pause/stop printing on the ” Device” interface.

Specification

Bambu Cool Plate
Bambu Engineering Plate
Bambu High Temperature Plate
Max Build Plate Temperature| 100 °0
Speed| Max Speed of Toolhead| 500 mm/s
Max Acceleration of Toolhead| 20 m/s’
Max Hot End Flow| 32 tarns @ABS(Model: 150•150mm single wall;
Material: Bambu ABS; Temperature: 280 ° C)
Cooling| Part Cooling Fan| Closed Loop Control
Hot End Fan| Closed Loop Control
Control Board Fan| Closed Loop Control
Chamber Temperature Regulator Fan| Closed Loop Control
Auxiliary Part Cooling Fan| Closed Loop Control
Air Fitter| Activated Carbon Filter
Supported Filament| PLA, PETG, TPtJ, ABS, ASA, PVA, PET| Ideal
PA, PC| Capable
Carbon/Glass Fiber Reinforced Polymer| Not Recommended
Sensors| Chamber Monitoring Camera| Low Ratearpera 1280 x 720/ 0.5fps ,
iimeaPse NWPortea
Filament Run Out Sensor| Yes
Filament Odometry| Optional with AMS
Power Loss Recover| Yes
Physical Dimensions| Dimensions(WxDxH)| 389′1389’458mm’
---|---|---
Net Weight| 12.95kg
Electrical Requirements| Input Voltage| 100-240 VAC, 50/60 Hz
Max Power| 1000W@220V, 350W@110V
USB Output Power| 5V/1.5A
Electronics| Display| 2.7-inch 192×64 Screen
Connectivity| Wi-Fi, Bluetooth, Bambu-Bus
Storage| Micro SD Card
| Control Interface| Button, APP, PC Application
Motion Controller| Dual-Core Cortex M4
Software| Slicer| Bambu Studio
Support third party slicers which export standard
G-code such as Superslicer, Prusaslicer and Cura,
but certain advanced features
may not be supported.
Slicer Supported OS| MacOS, Windows
Wifi| Frequency Range| 2412MHz-2472MHz(CE)
2412MHz-2462MHz(FCC)
2400MHz-2483.5MHz(SRRC)
Transmitter Power (EIRP)| .s21.5c1I3m(FCC)
.s20dBm(CE/SRRC)
Protocol| IEEE802.11 b/g/n
Bluetooth| Frequency Band| 2402MHz-2480MHz(CE/FCC)
2400MHz-2483.5MHz(SRRC)
Transmitter Power (EIRP)| s20dBm(FCC/SRRC)
<10dBm(CE)
Protocol| BLE5.0

Bambu Studio
Bambu Handy
https://bambulab.com/download

  https://www.bambulab.com/download

Customer Support
Please visit the Bambu Lab Wiki for more setup and maintenance tutorials. https://wiki.bambulab.com/en/home

https://wiki.bambulab.com/en/home

If you need support, please try either of the two approaches:
Approach 1 : Create a support ticket on the Official Website

Approach 2: Create a support ticket on the Bambu Handy App

Enjoy!
www.bambulab.com

References

• Bambu Lab | Unleash Your Creativity with Bambu Lab 3D Printers - Bambu Lab
• Software - Bambu Lab
• Software Studio - Bambu Lab
• Bambu Lab Wiki Homepage | Bambu Lab Wiki

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>