Bambu Lab PF002-A 3D Printers User Guide

Bambu Lab PF002-A 3D Printers

What’s In The Box

Accessory Box

Install Build Plate

Install the build plate with correct orientation, aligning the edge with the heatbed.

Unlock Heatbed

1. Flip the base housing 90 degree to the side opposite to the screen.
2. Use Allen Key H2 to remove the 4 highlighted screws at the bottom of the Base Housing to unlock the heatbed (Be careful when fully releasing the heatbed; use foam padding in the package to protect the heatbed from swinging).

Mate Base Housing & Printer Frame

1. Put the Printer Frame on the table as shown above.
2. Tilt the Base Housing about 45 degree to pass through the Printer Frame. (Use the screen as indicator for orientation)
3. Align the slot with the Printer Frame as shown in the diagram.
4. Slowly lower the Base Housing until it is fully flush with the Printer Frame on the table.

Unlock Tool head

1. Cut the ziptie and cardboard wrapped around the tool head and X-axis.
2. Remove the 7zipties and 2foam paddings on the printer frame.

Remove Y-Axis Cover

1. Push the heatbed fully to the front end, where the screen is located.
2. Open the Y-axis cover.
3. Pull out the Y-axis cover gently.

Lock Base Housing

1. Install 10*ST3-23 Screws (For Base Housing) in the holes highlighted in green.
2. Push the heatbed to the other end.

Install 2*ST3-23 Screws (For Base Housing) in the holes highlighted in green.

Put Cover Back

1. Push the heatbed fully to the front end, where the screen is located.
2. Gently slide the Y-axis cover back into place.
3. Make sure to align the clip.

Place On Table

Turn the A 1 90 degree onto its rear, laying it on the edge of a table. (It is recommended to cover the table with cardboard for protection.) Please make sure the printer is secure on the table while following the steps.

Plug In Cable Box

1. Align the 2 clips on the cable box with the holes on the Base Housing.
2. Slide up the cable box until the Type-C cable clicks in place. (DO NOT force the insert.)
3. Make sure the cable box is nice and flush in the slot, then screw in the pre-installed screw highlighted in green.

Plug In Connectors

1. Plug in the 3 harnesses according to color.
2. Tuck the harness into the cable slot and then close the cover.

Fold Out Touch Screen

Fold out the touch screen. Make sure the touch screen is in place as shown in the graph.

Install Purge Wiper

Push the tool head to the middle of the rail, leaving enough space for purge wiper installation.

1. Slide in Purge Wiper unit into the slot at the end of the X-axis.
2. Install the 1*M3-12 screw from the accessory box to fix the Purge Wiper in place.

Powering On

Plug in the power cable and turn on the A 1 using the power switch on the back.

Please leave a safety margin: of 198mm at the back and 90mm at the front.

Network Setting

1. Follow the instructions until I you see this screen. Press “Select Wi-Fi” to search for available network.
2. Select your preferred network.
3. Input the passcode, and then press “OK”.

Printer Binding

1. Download the Bambu Handy App. Register and log in to your Bambu Lab account.
2. Use Bambu Handy to scan the QR code on the screen, and bind your printer to your Bambu Lab account.
3. Follow the instructions on the screen to complete the initial calibration. It is normal to have vibration and noise during the calibration process.

External Spool (for non-AMS use case)

1. Assemble the spool holder.
2. Connect the tool head filament inlet (either one of four) and the filament guide with the 600mm PTFE tube as shown in the diagram.
3. Install the cable organizer as shown in the graph.
4. Hang filament spool on spool holder then feed the filament line into the PTFE tube as shown in the diagram.

First Print

1. Press “Print Files” to access the preloaded models on the SD card.
2. Select the model you want to print.
3. Turn on “Use AMS” if you are using filaments on AMS. Turning on “Bed leveling” is recommended. Turn on “Timelapse” for timelapse video recording.

Specification

Bambu Studio Bambu Handy
https://bambulab.com/download

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>