Bambu Lab P1S Combo 3D Printer Instruction Manual
- June 13, 2024
- Bambu Lab
Table of Contents
- Bambu Lab P1S Combo 3D Printer Instruction Manual
- Warning
- Component Introduction
- Accessory Specification
- AMS & Tool Head Unlock
- AMS Assambely
- Spool Holder Assembly
- Hot Bed Unlock & Screen Installation
- Printer Binding
- First Print
- Bambu Studio
- Bambu Studio
- Bambu Studio
- Specification
- Customer Support
- Read More About This Manual & Download PDF:
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Bambu Lab P1S Combo 3D Printer Instruction Manual
Warning
When operating the AMS, we recommend using Bambu Filament, which has been
thoroughly tested to work with the AMS.
Please make sure to avoid using soft materials like TPU or damp PVA, as they
can get stuck in the AMS.
ŦųşşŅDžŦŦşŅŅĵƌğùŮěŅĒ滺滵ĻĻ瀲滻滽ĻĻ澳ªýěğēěĵƒŢýóŅĻĻýĽùųŦğĽēǁĵÖĻýĽŮƌğŮěşĵÖŦŮğóŦşŅŅĵŦ
ŮěÖŮǁŮóŅŢŢýóŮĵƒğĽŦğùýŮěý\…澳DĒƒŅųşŢýĒýŢŮŅųŦýóÖŢùòŅÖŢùŦşŅŅĵŦ澴ƌýŦŮŢŅĽēĵƒÖùƋğŦýųŦğĽēÖŦşŅŅĵ
adapter to reduce the risk of slippage and debris getting left behind in the
AMS.
DĒƒŅųŢųĽğĽŮŅÖĽƒğŦŦųýŦƌğŮěŦşýóğǁóǁĵÖĻýĽŮŦ澴şĵýÖŦýĵýŮųŦıĽŅƌŦŅŮěÖŮƌýóÖĽşŢŅƋğùýòýŮŮýŢÖùƋğóý
to our community.
Component Introduction
Accessory Specification
AMS & Tool Head Unlock
Take out the accessory box. Use Allen Key H2 to remove the screws as pictured.
Take out the AMS by sliding it out throughthe top.
Remove the four screws as the arrows indicate. T
Remove the carboard from the tool head.
Romove the foam from the excess chute
AMS Assambely
Spool Holder Assembly
Remove the screw as pictured with an Allen Key H2
Secure the spool holder with two screws from the
Hot Bed Unlock & Screen Installation
Remove the three screws with an Allen Key H2 to unlock the hot bed.
Attention: Bend the LCD cable towards the opening on the back of the screen as pictured.
into the terminal as pictured
Inset the screen back to the slot on the printer, then lock it by pushing it to the left
Printer Binding
-
Download the Bambu Handy App. Register and log in to your Bambu Lab account.
-
Connect the printer to power. Follow the instructions on the screen until getting to the page shown on the right side
-
Use Bambu Handy to scan the QR code on the screen, and bind your printer with your Bambu Lab account.
-
DO NOT remove the protective foam from beneath the hot bed until after the initial calibration is complete
First Print
Select “II” and select a file to start the first print. *We recommend using one of the pre-loaded files as a first test print. All the pre-loaded files can be printed with PLA Basic or PLA Matte.
Place at least one spool of Bambu Filament into the AMS. Turn on the power to start the printer and the AMS. Insert the filament into the filament inlet. The filament will be automatically pre-loaded when detected. We recommend first printing a single-color model with the supplied Bambu PLA.
Bambu Studio
Download Bambu Studio: https://bambulab.com/en/download/studio
Log in to Bambu Studio with your Bambu Lab account, which is the same for the Bambu Online store. Create or open a project.
Bambu Studio
Slice the model, select your printer and send the model to print
Bambu Studio
During printing, you can remotely monitor your print, or pause/stop printing on the
Specification
Customer Support
Please visit the Bambu Lab Wiki for more setup and
maintenance tutorials.
https://wiki.bambulab.com/en/home
If you need support, please try either of the two approaches: Approach 1: Create a support ticket on the Official Website
Approach 2: Create a support ticket on the Bambu Handy App
Read More About This Manual & Download PDF:
References
- Software - Bambu Lab
- Bambu Lab | Unleash Your Creativity with Bambu Lab 3D Printers - Bambu Lab
- Software Studio - Bambu Lab
- Bambu Lab Wiki Homepage | Bambu Lab Wiki
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>