Bambu Lab X1 3D Printer User Guide
- June 5, 2024
- Bambu Lab
Table of Contents
Bambu Lab X1 3D Printer User Guide
Component Introduction
Accessory Specification
Tool Head Unlock
Screen Installation
Spool Holder Assembly
Hot Bed Unlock
Filament Loading
Specification
If you run into any issues during the guided setup, we are here to help. Customersupport@bambulab.com
Disclaimer and Warning
Thanks for purchasing a Bambu Lab product. The information in this document
affects your safety and you regal rights and responsibilities. Read this
entire document carefully to ensure pre per configuration before use. Failure
to read and follow instructions aid warnings in this document may result in
serious injury to yourself or others, damage to your Barn bu Lab product, or
damage to other objects in the vicinity. This document and other collateral
documents are subject to charge at the sole discretion of Bambu Lab By using
this product, you hereby signify that you have read this disclaimer and
warning carefully and that you understand and agree you are solely responsible
for your own conduct while using this product, and for any consequences
thereof You agree to use this product only for purposes that are proper and in
accordance with all applicable laws, rules and regulations, and all terms,
precautions, practices, policies, and guidelines Bambu Lab has made and may
make available. Bambu Lab accepts no liability for damage, or injury or any
legal responsibility incurred directly or indirectly from the use of the
product. The user shall observe safe and lawful practices including, but not
limited to, those set forth in this document Bambu lab is a trademark of
Shenzhen Tuohy Technology Co., Ltd. and its affiliated companies. Names of
products. brands, etc., appearing in this manual are trademarks or registered
trademarks of their respective owner companies.
Before You Start
The following documents have been produced to help you safely operate and make
full use of your
Bambu Lab X1 Series 3D Printer
Bambu Lab X1 Series 3D Printer Disclaimer and Safety Guidelines
Bambu Lab X1 Series 3D Printer Quick Start Guide
Check t hat you have all the included parts. Please review the entire Quick
Start Guide before operating the printer.
Read the Disclaimer and Warning above to understand your legal rights and
responsibilities. If you have any questions or problems during the
installation, maintenance, or use of this product, please contact a Bambu Lab
authorized dealer.
Safety Guidelines
- The product must be disconnected from the power supply before carrying out any installation or maintenance work
- Installation and maintenance must be carried out by a skilled worker in compliance with the manufacturer’s instructions and local safety regulations
- Do not use multiple plug adapters or extension leads
- Do not touch the product with any wet part of t he body and do not operate it while barefoot
- Do not reach inside the appliance while it is in operation
- Children using or near the printer must be accompanied and supervised by a responsible adult at all times.
- This product is designed solely for indoor use. It should be kept in a dry environment
- The recommended operating temperature for the appliance is between o·c to 40″C (32″F to 104″F).
- The recommended humidity level is under85%
- The product should be positioned on a dean, stable and flat workbench
- The product should be kept it in a well-ventilated location.
Compliance Information
FCC Compliance Notice
SuppUer’s Declaration of Conformity
Product name: X1/X1-Carbon
Model Number: PF001-NPF001-P
Responsibility Party: Shenzhen Tuozhu Technology Co.,Ltd. (Bambulab USA Incl
Responsibility Party Address: 8000 Centre Park Drive. STE 330, Austin. TX,
78754
Website: www.bambulab.com
We. Shenzhen Tuozhu Technology Co.,Ltd. (Bambulab USA Inc} . being the responsible party, declares that the above mentioned model was tested to demonstrate compliance with all applicable FCC rules and regulations.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and. if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
t here is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception. which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
-Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
ISED Compliance Notice
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s license-exempt RSS(s). Operation is subject to the
following two conditions
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
EU Compliance Statement
Hereby, Shenzhen Tuozhu Technology Co., Ltd. declares that the radio equipment
type X1/X1-Carbon is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of
conformity is available at
the following internet address: www.bambulab.com/eum-
complTance
GB Compliance Statement
Hereby, Shenzhen Tuozhu Technology Co .. Ltd. declares that the radio
equipment type X1/X1-Carbon is in
compliaoce with Radio Equipment Regulations 2017. The full text of the GB
declaration of conformity is available at the following internet
address: www.bambulab.com/euro-compliance
Complies with 21 CFR 1040.10 and 1040.11 except for conformance with IEC
60825-1 Ed.3.,as described in Laser
Notice No.56,dated May8,2019
www.bambulab.com
Copyright© 2022 Bambu Lab All Rights Reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>