VEVOR D034 Dent Repair Tool Kit User Manual
- May 15, 2024
- VEVOR
Table of Contents
D034 Dent Repair Tool Kit
“`html
Specifications:
- Product Name: Dent Repair Tool Kit
- Manufacturer: Vevor
- Includes: Plastic tabs, Metal tabs, 12V vehicle glue gun
- Features: Complete range of shapes and sizes, durable design,
elegant appearance, fast-melting glue stick
Product Usage Instructions:
Notice:
-
Do not use a car charge glue gun if the dent is on the engine
hood due to high temperature. -
Avoid repairing under direct sunlight to prevent temperature
impact on the glue stick. -
Apply glue starting from the center of the tab in a circular
motion for even coverage.
Tab Types:
-
Plastic tabs: High-quality, reusable, available in 6 sizes and
shapes -
Metal tabs: Strong adhesive ability, suitable for various dent
types
Glue Gun Features:
- Independent design with 12V power
- Elegant appearance with a bronze nozzle
- Fast-melting glue stick for efficient repairs
- Long 2-meter power line for convenience
Usage Tips:
If the glue becomes fragile in cold weather, apply hot water on
the dent before applying the glue for better adhesion.
Attention:
-
Avoid using generic glue sticks or tools as they may damage the
paint. Use professionally designed tools for effective
repairs. -
If your car paint is not original, refrain from using these
tools to prevent paint damage.
FAQ:
Q: To what degree can the tool reach?
A: This repair tool can fix 70%-80% of dents,
especially smooth and hail dents. Angular or sharp object-induced
dents may be challenging to repair.
Q: Is the operation easy?
A: Yes, it is straightforward. Even beginners
can handle it by following our detailed tutorials carefully.
If you encounter an unrepaired dent or a bump after repair:
- Press the bump with your thumb until it flattens.
- If unsuccessful, use a tap down pen and a rubber hammer to
gently knock the bump until successful. Avoid excessive force.
Remember, repeat the steps if needed until the dent is well
repaired.
“`
Technical Support and E-Warranty Certificate www.vevor.com/support
Dent Repair Tool Kit
We continue to be committed to provide you tools with competitive price. “Save
Half”, “Half Price” or any other similar expressions used by us only
represents an estimate of savings you might benefit from buying certain tools
with us compared to the major top brands and doses not necessarily mean to
cover all categories of tools offered by us. You are kindly reminded to verify
carefully when you are
placing an order with us if you are actually saving half in comparison with
the top major brands.
1. Find the dent and clean it with a rag and alcohol. 2. Observe the shape
and size of the dent, estimate where to pull the dent out, and mark it with a
marking pen. 3. Then clean the glue stick with alcohol to remove the grease on
its surface. 4.Insert the glue stick into the glue gun and connect the gun to
the power supply, then heat it for about 2-3 minutes till the hot melt glue
starts to spill out from the gun. 5. Choose a tab that matches the shape and
size of the dent; apply hot melt glue on the tab with the glue gun; remember
to start from the center of the taband in a circle inside and out, and make
sure the glue is even and full on the tab. (Please note: Bigger tab should be
used for bigger dent because it has stronger traction, vice versa) 6. Align
the center point of tab with the dent center point, then quickly put the tab
on the dent and slightly press it. (Wait 3-5 minutes till it cools down with
only a little temperature when it has strongest viscosity.) 7. Buckle the
puller till it is fastened, hold the handle of the puller, impact upwards,
gradually increase the force, repeat several times till the surface of the
dent flattens or slightly bulges (do not impact too fiercely to avoid the tab
off the car body) 8. If the center of some small dents is deeper than around,
please use the rubber hammer to tap on the around part; that will make the
dent more smooth to process. 9. After repair, spay alcohol on the part covered
by glue and remove it with a scraper. 10. Check the result; if not ideal,
repeat the above steps till you get what you want.
Select correct glue sticks: 1. Transparent glue stick: For Japanese cars which
have thin paint. Used for all natural temperature. 2. Yellow glue stick: For
European and American cars which have thick paint. And it is a better choice
to deal with small dents. 3. Black glue stick: For all cars. And the effect is
better in the temperature of 20¥-28¥.
1. Find the dent and clean it with a rag and alcohol. 2. Observe the shape
and size of the dent, estimate where to pull the dent out, and mark it with a
marking pen. 3. Then clean the glue stick with alcohol to remove the grease on
its surface. 4. Insert the glue stick into the glue gun and connect the gun to
the power supply, then heat it about for 2-3 minutes till the hot melt glue
starts to spill out from the gun. 5. Choose a tab that matches the shape and
size of the dent; apply hot melt glue on the tab with the glue gun, remember
to start from the center of the tab and in a circle inside and out, and make
sure the glue is even and full on the tab. (Please note: Bigger tab should be
used for bigger dent because it has stronger traction, vice versa) 6. Align
the center point of tab with the dent center point, and then quickly put the
tab on the dent and slightly press it.(Wait 3-5 minutes till it cools down
with only a little temperature when it has strongest viscosity.) 7.Buckle the
lifter til it is fastened, hold the handle of the downwards,gradually increase
the force, repeat several times till the surface of the dent flattens or
slightly bulges. Deal with this slowly and carefully. 8. If the center of some
small dents is deeper than around, please use the rubber hammer to tap on the
around part that will make the dent more smooth to process.
1. Find the dent and clean it with a rag and alcohol. 2. Observe the shape
and size of the dent, estimate where to pull the dent out, and mark it with a
marking pen. 3. Then clean the glue stick with alcohol to remove the grease on
its surface. 4. Insert the glue stick into the glue gun and connect the gun to
the power supply, then heat it about for 2-3 minutes till the hot melt glue
starts to spill out from the gun. 5. Choose a tab that matches the shape and
size of the dent; apply hot melt glue on the tab with the glue gun, remember
to start from the center of the tab and in a circle inside and out, and make
sure the glue is even and full on the tab. (Please note: Bigger tab should be
used for bigger dent because it has stronger traction, vice versa) 6. Align
the center point of tab with the dent center point, then quickly put the tab
on the dent and slightly press it. (Wait 3-5 minutes till it cools down with
only a little temperature when it has the strongest viscosity.) 7. Buckle the
nut, screw it till the surface of the dent flattens or slightly bulges. Deal
with this slowly and carefully. 8. If the center of some small dents is deeper
than around, please use the rubber hammer to tap on the around part that will
make the dent more smooth to process. 9. After repair, spay alcohol on the
part covered by glue and remove it with a scraper. 10. Check the result; if
not ideal, repeat the above steps till you get what you want.
*Notice:
1. Do not use a car charge glue gun if the dent is on the engine hood.
Because you need to start the car, it will cause a high temperature, which
will influence the glue stick’s effect. 2. Do not repair under the blazing sun
because the high temperature of the car body will influence the effect of the
glue stick. 3. When applying the glue, remember to start from the center of
the tab and in a circle inside and out, and make sure the glue is even and
full on the tab.
There are 2 kinds of tabs. 1. Plastic tabs
1). To dissolve the attached impurity, the plastic tabs should be soaked for 3
hours with alcohol before use. 2). Heat the glue sticks with the glue gun, and
apply hot melt glue on the tab evenly with proper amount depending on its
viscosity and car body condition. 3). Put the tab with glue on the dent,
slightly press it. Do not press fiercely to ensure a certain thickness of
glue. 4). Choose the right tabs though observing the shape and size of the
dent. Choose thin tabs for cars with soft body and thin paint and thick tabs
for cars with hard body and thick paint.
2. Metal tabs
The quality is the best; adhesive ability is the strongest; it can be used
repeatedly; 6 size and shape is available. Features: A complete range of
shapes and sizes are available to deal with all kinds of dents and it applies
to all car body types.
1. There are 2 types of glue guns, one is a vehicle glue gun, and the other
is a 220V glue gun. The difference is the connector. The connector of the
vehicle glue gun can directly connect with the car, while that of the 220V
glue gun cannot. 2. The voltage of the vehicle glue gun is 12V; you can
directly insert it into cigarette lighter, insert the glue stick, and then
turn on the switch to start. Wait for 2-3 minutes till the glue stick melt and
the temperature inside can reach to 160¥. 3. The 220V glue gun needs to be
connected with power supply, insert the glue stick and then turn on the switch
to start.
Features:
The 12V vehicle glue gun is our independent design. It is durable. The
appearance is elegant and nozzle is bronze. The glue stick can melt fast. The
power line is 2 meters long which is 0.5 meters longer than ordinary wires.
Q&A
Q: Which dent can be repaired and which cannot? A: The smooth and hail dent
can be 100% repaired, and the angular part needs more patience with different
tools. The tiny dent which is hit by sharp object is difficult to repair. If
the part with tiny dent can be removed or the back side of the dent can be
contacted directly, you can directly deal with it with dent tester-LED line
board or ordinary line board, tap down pen and tap down hammer. Remember never
use a iron hammer or other hard objects to repair, because the paint will be
damaged.
Q: To what degree can the tool reach? A: This repair tool can repair 70%-80%
dents. The smooth and hail dent can be well repaired. The angular dent, line
dent and dent caused by sharp objects are difficult to repair. But you can
still repair it by knocking the around part of the dent with a rubber hammer
first. But it doesn’t work if the paint has been damaged.
Q: Is the operation easy? A: It is very easy.Even a beginner without any
experience can handle as long as he or she read and watch our image-text and
video tutorial carefully.
Q: If the glue doesn’t work well, the viscosity is not enough, how to solve
it? A: 1.The glue works better in a sunny day and in the temperature of
20¥-28¥. 2. The viscosity of the glue is influenced by the humidity and
temperature. Generally, the hot melt glue will dry within 2-5 minutes in
summer and 1-3 minutes in a cold day. It depends on actual situation,sometimes
20 seconds is enough. 3. If the tab is off in the process of operating, it may
be because the amount of glue is not enough or the temperature of car body is
too high or your operation is not correct. The problem will be gone if you
apply more glue, turn off the car engine, and then repeatedly operate.
Warm tips:
If the glue becomes fragile in an extremely cold day, you can apply hot water
on the dent first, and then apply the glue.
Attention:
1. Glue sticks or repair tools bought from some local stores may fail to do
the job as expected. They can’t guarantee a good repair effect and may damage
the paint. Our tools and glue sticks are professionally designed and applied
to car body with years of practical experience.The paint won’t be damaged and
the repair effect is pretty good if you operate correctly. 2. If the paint of
your car is not original, we suggest you not to buy our tools as it may damage
the paint.
Notes :
If the product you received has quality problems or it is broken when you
received or you find a shortage in number, please do not hesitate to tell us
via photos or e-mails, we will reply you in time. Please read the instruction
carefully before you use our product, and according the instruction to operate
it. If there is any question,please feel free to contact us, we will arrange
our technical staff to help you. Please give us a reasonable and fair feedback
if you think our product is practical, it is really helpful to other person
when they want to buy this product. You can not use the vehicle glue gun when
there is dent on the hood need to repair, because the vehicle glue gun needs
to start the car to charge it, and this action will cause the hood gets hot,
if the hood got hot, the glue will be soft, and if the glue was soft, the
viscosity will be weak, but except the place where its weather is extremely
cold.
slide hammer dent puller
slide hammer dent puller
b b
b
b b
b b
b
Kindly reminder: If it is still unrepaired after above steps, you can repeat the steps several times till it is well repaired. If the dent is repaired, but there’s a bump on it, you can do as following steps: 1. Press the bump with your thumb continually till it flattens. 2. If fail after the first step, you can use a tap down pen and aim at the bump, then knock it slightly with a rubber hammer. You can repeat till successful (Please do not knock with too much force).
Kindly reminder: If it is still unrepaired after above steps, you can repeat the steps several times till it is well repaired. If the dent is repaired, but there’s a bump on it, you can do as following steps: 1. Press the bump with your thumb continually till it flattens. 2. If fail after the first step, you can use a tap down pen and aim at the bump, then knock it slightly with a rubber hammer. You can repeat till successful (Please do not knock with too much force).
Kindly reminder: If it is still unrepaired after above steps, you can repeat the steps several times till it is well repaired. If the dent is repaired, but there’s a bump on it, you can do as following steps: 1. Press the bump with your thumb continually till it flattens. 2. If fail after the first step, you can use a tap down pen and aim at the bump, then knock it slightly with a rubber hammer. You can repeat till successful (Please do not knock with too much force).
Product List
Model
D034 D035/D036 D037/D038 D039/D040 D041/D042 D043/D044 D045/D046
Picture
Slide Hammer
1
1
1
Bridge Dent Puller
1
1
1
1
Golden Dent Puller
1
1
1
1
Small Suction Cup
2
2
Large Suction Cup
1
1
Glue Gun
1
1
1
1
1
1
Glue Stick
12
12
13
15
15
20
Plastic Tab
20
20
20
20
50
Tab of Bridge Puller
6
6
6
6
Groove of Puller Line
2
2
2
Puller Line
4
4
4
Spray Bottle
1
1
1
1
1
1
Cloth
1
1
1
1
1
1
1
Tool Bag
1
1
1
1
1
Tap-down Pen
5
5
5
1
1
Hammer
1
1
1
1
1
Tip of Tap-down Pen
8
8
Scraper
1
1
1
1
1
1
Glove
2
2
2
2
2
2
2
Reflective Board
1
1
Air Pump Wedge
1
1
Technical Support and E-Warranty Certificate www.vevor.com/support
Made In China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>