EDIFIER S3000MKII Premium 2.0 Bluetooth Speaker System User Manual

EDIFIER S3000MKII Premium 2.0 Bluetooth Speaker System

What’s in the Box

Note

• Images are for illustrative purposes only and may differ from the actual product.
• The bundled USB connecting cable is for audio streaming only. Do not use it for device charging.
• For the need of technical improvement and system upgrade, the information and specifications contained herein may be slightly different from the actual product. If any difference is found, the actual product prevails.

Functional Operation

1. Volume control/input selection Press: input selection (Bluetooth→Line In → XLR→Optical→Coaxial→USB) Press and hold: enter standby mode or wake the speaker
2. Treble control
3. Bass control
4. Active speaker pairing button
5. Power switch
6. XLR (balanced) input
7. Line In input
8. USB type-B connector (used for USB digital audio input)
9. Optical input
10. Coaxial input
11. Power cable connector
12. Power switch
13. Power cable connector
14. Active speaker pairing button
15. Status indicator
16. OLED display window

Remote Control

Point the remote control to the remote receiving window on the speaker, the optimum operational distance is 7 meters. The displayed value in the display window will alert or blink when the system receives a remote control command .

1. Standby/wake (effective only when the speaker is turned on)
2. Remote control indicator
3. Custom sound effect
4. Monitor sound effect
5. Dynamic sound effect
6. Previous track/next track (Bluetooth/USB mode)
7. Volume up/volume down
8. Pause/play (Bluetooth/USB mode; other modes: press to mute/unmute)
9. Classic sound effect
10. Vocal sound effect
11. USB input
12. Bluetooth input
13. Optical/coaxial input
14. Line In/XLR (balanced) input

Five sound effects:

• CLASSIC: reproduces a classic HIFI sound.
• MONITOR: features a flat audio response curve, for sound with no coloration. DYNAMIC: more punch, more dynamic.
• VOCAL: human voice emphasized, singer’s position will seem closer to listener. CUSTOM: customize sound effects via the Edifier ConneX App. You can scan the QR code listed in the manual cover to download and install the Edifier ConneX App.

1.  As the illustration shows, press remote control batteries cover downwards with your thumb and follow the arrow direction to remove the cover, using two AAA batteries (note the “+” and “-” pole).
2. The batteries life are normally about 6 months; please replace them when the remote control is not sensitive or the control distance is shortened.
3. Never use old and new batteries together.

Note

• Do not place the remote control in places that are hot and humid.
• Do not charge the batteries.
• Remove the batteries when unused for a long period to avoid battery leakage.
• The batteries should not be exposed to excessive heat such as direct sun, fire or similar.
• Danger of explosion if batteries are incorrectly replaced. Replace only with the same or equivalent type.

Cable connection

1. As the illustration shows, connect to audio source devices and connect speakers to a power source using power cables.
2. Turn power switch on, the display window on the active speaker (R) will show the current audio source. Please select the correct audio source with the remote control.

Manually re-pair left and right speakers
Two speakers have been paired at the factory before shipment. After powering on, they will reconnect automatically with the indicator on the left speaker (L) in solid red. If the wireless connection fails to resume, follow the steps below to re-pair.

1. Power on the right speaker (R), and then press and hold the “Pair” button on its rear panel. The “PAIRING” icon will blink rapidly on the display.
2. Press and hold the “Pair” button on the rear panel of the left speaker (L). The red indicator on the left speaker (L) will blink rapidly.
3. Wait until the red indicator on the left speaker (L) is lit constantly. Then the pairing is complete and a wireless connection is established.

Note: If the red indicator on the left speaker (L) is in a breathing pattern, it indicates that the two speakers are not connected. Repeat the above steps.

Audio inputs

XLR (balanced) input

1. Connect audio source (CD player, decoder, etc.) to the balanced input port (note color matching) on the rear panel of the active speaker (R) using XLR balanced audio cable (XLR cable not included).
2. Press the “Volume/Input” dial on the rear panel of the active speaker (R), or press the “LINE/XLR” button on the remote control until the display window on the active speaker (R) shows “XLR”.
3. Play music on the connected device and adjust the settings to a desired level.

Line In input

1. Connect audio source (mobile phone, tablet, etc.) to the Line In input port (note color matching) on the rear panel of the active speaker (R) using 3.5mm-RCA audio cable or RCA-RCA audio cable.
2. Press the “Volume/Input” dial on the rear panel of the active speaker (R), or press the “LINE/XLR” button on the remote control until the display window on the active speaker (R) shows “LINE”.
3. Play music on the connected device and adjust the settings to a desired level.

Optical/Coaxial input

1. Connect audio source (Set Top Box, Blu-ray player, etc.) to the optical or coaxial input port on the rear panel of the active speaker (R) using fiber optic audio cable or coaxial cable (coaxial cable not included).
2. Press the “Volume/Input” dial on the rear panel of the active speaker (R), or press the “OPT/COAX” button on the remote control until the display window on the active speaker (R) shows “OPTICAL” or “COAXIAL”.
3. Play music on the connected device and adjust the settings to a desired level.

USB digital audio input
USB interface chip in the S3000MK is an XMOS chip used by high-end audio equipment. After being connected to PC, the USB interface will directly extract and play back digital audio signal in a manner similar to the “USB external audio streaming”, to avoid sound degradation and dynamic range compression caused by digital-to-analog conversion of PC audio streaming, and to ensure the restoration of original sound quality.

1. Connect USB type-A port on PC to the USB type-B input port on the rear panel of the active speaker (R) using the USB A-to-B data cable.
2. Press the “Volume/Input” dial on the rear panel of the active speaker (R), or press the “USB” button on the remote control until the display window on the active speaker (R) shows “USB”.
3. Play music on the connected device and adjust the settings to a desired level.

Note

• USB interface of S3000MK is built on USB Audio Class 2.0, which supports high-resolution audio with a sample rate up to 192kHz. To play such audio, a driver needs to be installed on your Windows computer. You can visit www.edifier.com, search for “S3000MKII”, go to its detail page, scroll down to the support information, and click the link to download the driver.
• For further information about the driver, access the following link for details: https://www.xmos.com/support/usb-audio-driver-support
• Make sure that S3000MK is set as the audio output device. (1) For Windows users, access “Control Panel”→”Sound”→”Play”→”Set as Default” to set “XMOS USB Audio” as the current audio output device. (2) For Mac users, access “System Preferences” →”Sound”→”Output” to select “EDIFIER S3000MKII” as the current audio output device.
• In USB mode, the following sample rates are supported: 44.1kHz, 48kHz, 96kHz, and 192kHz.

Note

• The play control in USB mode may vary depending on different audio player applications.
• The volume levels of S3000MK and your device are not synchronized. To adjust the volume levels, adjust separately.

Bluetooth input

1. Press the “Volume/Input” dial on the rear panel of the active speaker (R), or press the “ ” button on the remote control until the display window on the active speaker (R) shows “ “.
2. Select “EDIFIER S3000MKII” in your device (mobile phone, tablet, etc.) setting to connect.

Note

• On your Bluetooth device, you can search for and connect to S3000MK in any mode. S3000MK will try to connect to the device that is connected last time when powered on again. You can only play audio via Bluetooth when S3000MK is in Bluetooth mode.
• Pin code for connection is “0000” if needed.
• To enjoy all Bluetooth functions of this product, make sure that your audio source device supports A2DP and AVRCP profiles.
• To disconnect from the current Bluetooth device, press and hold the “Volume/Input” knob on the rear panel of the right speaker (R) or the “ ” button on the remote control for over 2s.

Specifications

• Total output power (RMS): L/R (Treble): 8W+8W
• L/R (Mid-range and bass): 120W+120W Frequency response: 38Hz-40kHz
• Audio inputs : Bluetooth, Line In, XLR, Optical, Coaxial, USB

Declaration for EU

• Frequency Band (Bluetooth): 2.402GHz ~ 2.480GHz
• Frequency Band (5.8G): 5.725GHz ~ 5.848GHz
• RF Power Output (Bluetooth): ≤10 dBm (EIRP)
• RF Power Output (5.8G): ≤14 dBm (EIRP)

There is no restriction of use.

Troubleshooting

No sound

• Check if the speaker is ON.
• Try to turn up the volume using the volume control or remote control.
• Ensure the audio cables are firmly connected and the input is set correctly on the speaker.
• Check if there is a signal output from the audio source.

Cannot connect via Bluetooth

• Disconnect from any Bluetooth device by pressing and holding the ” ” button on the remote control for over 2s, then try again.
• The effective Bluetooth transmission range is 10 meters; please ensure that operation is within that range.
• Try another Bluetooth device for connection.

The S3000MK does not turn on

• Check if the main power is connected, or if the wall outlet is switched on.

Noise coming from speakers

• EDIFIER speakers generate little noise, while the background noise of some audio devices are too high. Please unplug audio cables and turn the volume up, if no sound can be heard at 1 meter away from the speaker, then there is no problem with this product.

To learn more about EDIFIER, please visit www.edifier.com For EDIFIER warranty queries, please visit the relevant country page on www.edifier.com and review the section titled Warranty Terms. USA and Canada: service@edifier.ca South America: Please visit www.edifier.com (English) or www.edifierla.com (Spanish/Portuguese) for local contact information.

References

• Headphones, Speakers | A Passion for Sound -【Edifier】
• edifierla.com
• USB Audio Driver Support | XMOS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>