FLEETFLIX AI Pro Dash Camera User Guide
- June 4, 2024
- FLEETFLIX
Table of Contents
FLEET FLIX AI + PRO
Powerful, Reliable, and Fully Omtegrated
into Geotab,
This is the FleetFix Quick Start Guide.
www.FleetFix.com
| |
---|---|---
Installing the Cables
Sl – Reference the vehicle’s user manual to find the location of the fuse
box and OBD connector. Then check the ACC fuse specification on the box cover.
S2 – Pull out the ACC fuse.
S3 – Select the appropriate Blade Fuse Holder cable. Plug in the ACC fuse
that was removed from the fuse box into the Blade Fuse Holder cable, and then
plug in the other ACC fuse that we provided.
S4 – Plug in the Blade Fuse Holder cable into the ACC fuse slot in the
fuse box.
S5 – If using LDW, gray and pink input wires will need to be connected.
S6 – Remove the right panel I/O cover.
S7 – Feed the 12-pin connector of the OBD II Power Cable through the hole
on the right panel I/O cover.
S8 – Reinstall the right panel I/O cover. Make sure to tighten the screw.
S9 – Connect the other end of the OBD II Power Cable to the Blade Fuse
Holder cable.
S10 – Plug in the OBD II Power Cable to the OBD II connector in the
vehicle.
Mounting
Sl – Attach the adhesive tape mounting bracket or optional suction cup
onto the Fleetflix Dash Cam.
S2 – Find a suitable place to install the FleetFlix Dash Cam onto the
wind shield. Use alcohol to clean the glass before mounting the device. (It is
recommended to install the device in the center of the wind shield below the
review mirror.)
Installing the Micro SD Card (As Needed)
Sl – Loosen the screw of the right panel I/O cover, remove cover.
S2 – Locate the Micro SIM Card slot.
S3 – Insert a Micro SIM card into card slot. Use your fingernail to press
the card into the slot. When fully inserted, the card will snap into the slot.
Wire Color Guide for OBD Harness
| Yellow Input Ignition ACCl Connector
---|---
| Gray Wire Input Dedicated Left Blinker
| Pink Input Dedicated Right Blinker
| Orange Input
| Purple Input
| Blue Input
| Green Input
| Brown Output
Plugging in the 080 II Power Cable to the 080 II connector
WHAT ARE THE BENEFITS OF THE FLEETFLIX TECHNOLOGY?
The FleetFlix Al+ Pro dashcam is packed with the latest advancements in
technology, offering fleets of all sizes a powerful device to enhance driver
and fleet safety, and reduce safety-related costs.
The FleetFlix Al+ Pro is fully integrated into the Geotab P latform..
After installing the camera, the following measurements are needed
- Hood length – the distance from the front lens of the camera and the front bumper
- Vehicle width – the total width of the vehicle at its widest point in front of the camera (typically wheel arch to wheel arch)
- Camera height – the distance from the ground to the bottom of the camera Driver position – which side of the vehicle the steering wheel is on, (left hand is typical for American market vehicles)
After install has been completed and measurements have been saved in the database, the camera will need to be calibrated. To calibrate the camera properly you will need to take the vehicle on a short drive under these conditions:
- Good contrast for lane markers
- Capable of supporting 30+ mph for 3-5 minutes
- Avoids hills or turns
- Reasonable weather
- Light traffic
To start Calibration
While the vehicle is driving down the road in these optimal conditions, press
and hold down the driver alert button for 4 seconds. The camera will announce
“Calibration Started” and once complete camera will announce “Calibration
Done”. Once calibration is complete, your camera has been successfully set up,
and returned the button to driver alert. If the camera is ever removed or
unmounted, calibration will need to be completed again.
Give us a call for more information
www.fleetFlix.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>