midiplus WAVE Controller with 16 Plus 1 100mm Motorized Faders User Guide

May 15, 2024
Midiplus

midiplus Logomidiplus WAVE Controller with 16 Plus 1 100mm Motorized Faders -
Logo Quick Start Guide

Introduction

Thank you for choosing mdiplus WAVE. This is a compact 2.4 GHz wireless audio system that provides electronic instrument performers with a low-latency wireless stereo transmission solution. The WAVE transmitter has a 3.5mm headphone output for real-time monitoring with. Please read this manual before starting to use it to help you quickly understand the basic functions of WAVE.

Features

  • 2.4 GHz wireless stereo transmission
  • 16-bit/48kHz high-quality audio
  • Wide frequency response of 20 – 20000Hz
  • Low transmission latency as short as 9 milliseconds
  • Up to 7.5 hours of usage time

Hardware Features

midiplus WAVE Controller with 16 Plus 1 100mm Motorized Faders - Figure
1midiplus WAVE Controller
with 16 Plus 1 100mm Motorized Faders - Figure 2

  1. Pairing Button
  2. Status Indicator LED
  3. Power Switch
  4. Headphone Jack
  5. Charging Port

Indicator Light Status:

  1. Blue LED lights on: Paired and Connected
  2. Blue LED blinks slowly: Disconnected
  3. Blue LED blinks fast: Pairing Mode
  4. Red LED lights on: Charging ( Note: Device will automatically go into standby mode and cannot be used during charging)
  5. Red LED blinks: Low battery
  6. LED Off: Powered Off or Fully Charged

Pairing:
The TX (transmitter) and RX (receiver) are already paired at the factory. If there is a need to re-pair, you can follow the steps below for pairing.

  1. Turn on the power switches of both the TX (transmitter) and RX (receiver).
  2. Long-press the pairing button on either unit until the Blue LED blinking fast.
  3. Press the pairing button on the other device within 10 seconds. The indicator LED will turns blue if pairing successfully.
  4. If the operation over times or pairing is unsuccessful, please repeat the above steps.

Usage Instructions:

  1. Insert the TX (transmitter) into the 3.5mm output port of your electronic instrument or device.
  2. Plug the RX (receiver) into the 3.5mm input port of an active speaker or mixer.
  3. Turn on the power switches of both the TX (transmitter) and RX (receiver) first, and then turn on the power of the speaker.
  4. Ensure there are no obstructions or walls between the TX (transmitter) and RX (receiver), and make sure the straight-line distance does not exceed the effective operating range.

Note: The 3.5mm TRS plugs on the WAVE TX (transmitter) and RX (receiver) are unbalanced stereo connectors. If your devices use balanced interfaces, you will need to use a TRS to 2 TS adapter, otherwise, there might be phase cancellation or audio abnormalities.midiplus WAVE Controller with 16 Plus 1
100mm Motorized Faders - Figure 3

Specifications:

Model WAVE
Operating Frequency 2.4GHz
Sampling Frequency and Resolution 48kHz/16-bit
Latency ≤9ms
Operating Range ≤10m (actual distance may vary depending on the usage

scenario)
Battery Life| 7.5 hours
Frequency Response| 20Hz-20kHz
Input Impedance| 1MΩ
Audio Signalto-Noise Ratio| ≥75dB
Dimensions (including 3.5mm connector)| 55mm (length) x 26mm
(width) x 17mm (height)
Weight| TX: 13.8g, RX: 13.2g
Accessories| WAVE TX x 1, WAVE RX x 1, user manual,Charging cable

midiplus Logowww.midiplus.com

Documents / Resources

| midiplus WAVE Controller with 16 Plus 1 100mm Motorized Faders [pdf] User Guide
WAVE Controller with 16 Plus 1 100mm Motorized Faders, WAVE, Controller with 16 Plus 1 100mm Motorized Faders, Plus 1 100mm Motorized Faders, Motorized Faders
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals