GRANDSTREAM HT812 Analog FXS IP Gateway 2 Port + NAT Router User Guide Grandstream Networks, Inc. HT812/HT814 Series
- May 15, 2024
- GRANDSTREAM
Table of Contents
- HT812 Analog FXS IP Gateway 2 Port + NAT Router
- Grandstream Networks, Inc. HT812/HT814 Series
- Specifications
- Product Overview
- Feature Highlights:
- Key Features:
- Setting up the HT812/HT814:
- Using the Telephony Features:
- Q: How do I perform a factory reset?
- Q: Can I use the HT812/HT814 with any IP PBX system?
HT812 Analog FXS IP Gateway 2 Port + NAT Router
“`html
Grandstream Networks, Inc. HT812/HT814 Series
Specifications
Interfaces | HT812 | HT814 |
---|---|---|
Telephone Interfaces | Two (2) RJ11 FXS ports | Four (4) RJ11 FXS ports |
Network Interface | Two (2) 10/100/1000 Mbps Ethernet port (RJ45) | Two (2) |
10/100/1000 Mbps Ethernet port (RJ45)
LED Indicators| POWER, LAN, WAN, PHONE1, PHONE2| POWER, LAN, WAN, PHONE1,
PHONE2, PHONE3, PHONE4
Product Overview
The HT812/HT814 series from Grandstream Networks offers advanced
telephony features for your communication needs.
Feature Highlights:
-
* Supports multiple SIP profiles through FXS ports.
- 3-way voice conferencing capability.
- Wide range of caller ID formats supported.
Key Features:
-
* Call transfer, call forward, call-waiting.
- Do not disturb, message waiting indication.
- Multi-language prompts and flexible dial plan.
Product Usage Instructions
Setting up the HT812/HT814:
-
1. Connect the RJ11 FXS ports to your telephone devices.
- Connect the Ethernet port to your network.
Using the Telephony Features:
To make a call: Pick up the phone and dial the number. To
transfer a call: Press the transfer button and dial the recipient’s
number.
Frequently Asked Questions (FAQ)
Q: How do I perform a factory reset?
A: Locate the factory reset button on the device and press and
hold it for 10 seconds until the device restarts.
Q: Can I use the HT812/HT814 with any IP PBX system?
A: The HT812/HT814 is designed for seamless integration with
Grandstream’s UCM series of IP PBXs for Zero Configuration
provisioning.
“`
Grandstream Networks, Inc.
HT812/HT814 Series Administration Guide
HT812/HT814 Administration Guide
The HT812/HT814 analog telephone adaptors (ATAs) provide transparent
connectivity for analog phones and faxes to the world of internet voice.
Connecting to any analog phone, fax or PBX, the HT812/HT814 is an effective
and flexible solution for accessing internet-based telephone services and
corporate intranet systems across established LAN and internet connections.
This Grandstream Handy Tones are a new addition to the popular Handy Tone ATA
product family. This manual will help you to learn how to operate and manage
your HT812/HT814 analog telephone adaptors and make the best use of their many
upgraded features including simple and quick installation, 3-way conferencing,
direct IP-IP Calling, and new provisioning support among other features. The
HT812/HT814 are very easy to manage and configure, and they are specifically
designed to be an easy to use and affordable VoIP solution for both the
residential user and the teleworker.
PRODUCT OVERVIEW
The HT812/HT814 are 2/4 ports analog telephone adaptors (ATAs) that allow
users to create a high-quality and manageable IP telephony solution for
residential and office environments. Their ultra-compact size, voice quality,
advanced VoIP functionality, security protection and auto provisioning options
enable users to take advantage of VoIP on analog phones and enables service
providers to offer high quality IP service. The HT812/HT814 are an ideal ATA s
for individual use and for large scale commercial IP voice deployments since
they permit small and medium businesses to create integrated IP and PSTN
telephony systems that efficiently manage communication costs. HT812/HT814’s
inclusion of an integrated NAT router and dual 10/100/1000Mbps Ethernet WAN
and LAN ports enables a shared broadband connection between multiple Ethernet
devices as well as the extension of VoIP services to analog phones.
Feature Highlights
The following table contains the major features of the HT812/HT814:
HT812 / HT814
Support 2 SIP profiles through 2 FXS ports for HT812 and 4 FXS port for HT814
and dual 10/100/1000Mbps Ethernet port for HT812
Support 3-way voice conferencing.
Support wide range of caller ID formats.
Support advanced telephony features, including call transfer, call forward,
call-waiting, do not disturb, message waiting indication, multi-language
prompts, flexible dial plan and more.
Support T.38 Fax for creating Fax-over-IP.
TLS and SRTP security encryption technology to protect calls and accounts.
Automated provisioning options include TR-069 and XML config files.
Failover SIP server automatically switches to secondary server if main server
loses connection.
Use with Grandstream’s UCM series of IP PBXs for Zero Configuration
provisioning.
GR-909 Line Testing Functionalities.
Table 1: HT812/HT814 Features at a Glance
HT812/HT814 Technical Specifications
The following table resumes all the technical specifications including the
protocols/standards supported, voice codecs, telephony features, languages and
upgrade/provisioning settings for the HT812/HT814.
Interfaces
Telephone Interfaces
Two (2) RJ11 FXS ports for HT812. Four (4) RJ11 FXS sports for HT814.
Network Interface
Two (2) 10/100/1000 Mbps Ethernet port (RJ45).
LED Indicators
POWER, LAN, WAN, PHONE1, PHONE2 for HT812. POWER, LAN, WAN, PHONE1, PHONE2, PHONE3, PHONE4 for HT814.
Factory Reset Button
Yes.
Voice, Fax, Modem
Telephony Features
Caller ID display or block, call waiting, flash, blind or attended transfer, forward, hold, do not disturb, 3-way conference.
Voice Codecs
G.711 with Annex I (PLC) and Annex II (VAD/CNG), G.723.1, G.729A/B, G.722, G.726, iLBC, OPUS, dynamic jitter buffer, advanced line echo cancellation.
Fax over IP
T.38 compliant Group 3 Fax Relay up to 14.4kpbs and auto-switch to G.711 for Fax Pass-through.
Short/Long Haul Ring Load
For HT812: 3 REN, up to 1km on 24AWG line. For HT814: 2 REN, up to 1km on 24AWG line.
Caller ID
Bellcore Type 1 & 2, ETSI, BT, NTT, and DTMF-based CID.
Disconnect Methods
Busy Tone, Polarity Reversal/Wink, Loop Current.
Signaling
Network Protocols
TCP/IP/UDP, RTP/RTCP, HTTP/HTTPS, FTP/FTPS, ARP/RARP, ICMP, DNS, DDNS, DHCP, NTP, TFTP, SSH, Telnet, STUN, SIP (RFC3261), SIP over TCP/TLS, SRTP, TR-069.
QoS
Layer 2 (802.1Q VLAN, SIP/RTP 802.1p) and Layer 3 (ToS, Diffserv, MPLS).
DTMF Methods In-audio, RFC2833 and/or SIP INFO.
Provisioning and HTTP, HTTPS, SSH, FTP, FTPS, Telnet, TFTP, TR-069, secure and automated provisioning using TR069,
Control
syslog.
Security
Media
SRTP.
Control
TLS/SIPS/HTTPS/HTTP/SSH/Telnet.
Management
Syslog support, SSH, Telnet remote management using web browser.
Physical
Universal Power Supply
Input: 100-240VAC, 50-60Hz Output: 12V/0.5A for HT812. Output: 12V/1A for HT814.
Environmental
Operational: 32o 104oF or 0º 40ºC. Storage: 14o 140oF or -10º 60ºC. Humidity: 10 90% Non-condensing.
Dimensions and Weight
Dimension : 28.5 x 130 x 90 mm (H x W x D). Weight: 353.33g for HT812 and for 423.5g for HT814.
Compliance
Compliance
FCC/CE/RCM.
Table 2: HT812/HT814 Technical Specifications
GETTING STARTED
This chapter provides basic installation instructions including the list of
the packaging contents and also information for obtaining the best performance
with the HT812/HT814.
Equipment Packaging
The HT812/HT814 ATAs packages contain:
Figure 1: HT812 Package Contents
Figure 2: HT814 Package Contents Check the package before installation. If you
find anything missing, contact your system administrator.
HT812/HT814 Ports Description
The following figure describes the different ports on the back panel of the
HT812/HT814.
Figure 3: HT812 Back Panel
Figure 4: HT814 Back Panel
Phone 1 & 2 (HT812) Phone 1,2,3 & 4 (HT814)
Connects the analog phones / fax machines to the ATA using an RJ-11 telephone cable.
WAN
Connects the ATA to your router, switch or modem using an Ethernet RJ45 network cable. co
LAN
Connects the ATA to your PC or switch using an Ethernet RJ45 network cable.
DC Power
Connects the ATA to PSU (12V 0.5A for HT812) and (12V 1A for HT814).
Reset
Factory reset button. Press for 7 seconds to reset factory default settings.
Table 3: HT812/HT814 Connectors Definitions
Connecting HT812/HT814
The HT812/HT814 are designed for easy configuration and easy installation, to
connect your HT812/HT814, please follow the steps below:
Scenario 1: Connecting the HT812/HT814 using WAN Port
When connecting HT812/HT814 using the WAN port, they will act as simple DHCP
Client.
1. Insert a standard RJ11 telephone cable into the phone ports and connect
the other end of the telephone cable to a standard touch-tone analog
telephone.
2. Connect the WAN port of the HT812/HT814 to a router, switch or modem using
an Ethernet cable. 3. Insert the power adapter into the HT812/HT814 and
connect it to a wall outlet and make sure to respect the technical
specifications of the power adapter used. 4. Power, WAN and Phone LEDs will be
solidly lit when the HT812/HT814 is ready for use.
Scenario 2: Connecting the HT812/HT814 using LAN Port
When connecting the HT812/HT814 using the LAN port, they will act as a router
and DHCP serving addresses, the devices connected with HT812/HT814 LAN will
pull DHCP addresses from your HT812/HT814.
1. Insert a standard RJ11 telephone cable into the phone ports and connect
the other end of the telephone cable to a standard touch-tone analog
telephone.
2. Connect a computer or switch to the LAN port of the HT812/HT814 using an
Ethernet Cable. 3. Insert the power adapter into the HT812/HT814 and connect
it to a wall outlet and make sure to respect the technical
specifications of the power adapter used. 4. Power, LAN and Phone LEDs will be
solidly lit when the HT812/HT814 is ready for use.
Please make sure to enable NAT Router under Web GUI Basic Settings Device
Mode.
Figure 5: Connecting the HT812/HT814
HT812/HT814 LEDs Pattern
There are four (4) LED types that help you manage the status of your
HT812/HT814.
LED Lights Power LED
Figure 6: HT812/HT814 LEDs Pattern
Status The Power LED lights up when the HT812/HT814 are powered on and it
flashes when the HT812/HT814 is booting up.
WAN LED
The WAN LED lights up when the HT812/HT814 are connected to your network through the WAN port.
LAN LED
The LAN LED lights up when the HT812/HT814 are connected to your network through the LAN port.
The phone LEDs indicate status of the respective FXS port-phone on the back panel
Phone LED 1&2 (HT812)
Phone LED 1,2,3 & 4 (HT814)
OFF Unregistered ON (Solid Blue) Registered and Available Blinking every 500 ms Off-Hook / Busy Slow blinking FXS LEDs indicates voicemail
Table 4: HT812/HT814 LEDs Pattern Description
CONFIGURATION GUIDE
The HT812/HT814 can be configured via one of two ways:
The IVR voice prompt menu. The Web GUI embedded on the HT812/HT814 using PC’s
web browser.
Obtain HT812/HT814 IP Address via Connected Analogue Phone
HT812/HT814 are by default configured to obtain the IP address from DHCP
server where the unit is located. To know which IP address is assigned to your
HT812/HT814, you should access to the “Interactive Voice Response Menu” of
your adapter via the connected phone and check its IP address mode.
Please refer to the steps below to access the interactive voice response menu:
1. Use a telephone connected to phone ports (FXS) of your HT812/HT814. 2.
Press *** (press the star key three times) to access the IVR menu and wait
until you hear “Enter the menu option “. 3. Press 02 and the current IP
address will be announced.
Understanding HT812/HT814 Interactive Voice Prompt Response Menu
The HT812/HT814 have a built-in voice prompt menu for simple device
configuration which lists actions, commands, menu choices, and descriptions.
The IVR menu works with any phone connected to the HT812/HT814.
Pick up the handset and dial “***” to use the IVR menu.
Menu Voice Prompt
Main Menu
“Enter a Menu Option”
Options Press “*” for the next menu option Press “#” to return to the main menu Enter 01-05, 07,10, 12-17,47 or 99 menu options
“DHCP Mode”,
01
“Static IP Mode”
“PPPoE Mode”
Press “9” to toggle the selection
If using “Static IP Mode”, configure the IP address information using menus 02
to 05.
If using “Dynamic IP Mode”, all IP address information comes from the DHCP
server automatically after reboot.
If using “PPPoE Mode”, configure PPPoE Username and Password from web GUI to
get IP from your ISP.
The current WAN IP address is announced
02
“IP Address” + IP address
If using “Static IP Mode”, enter 12-digit new IP address. You need to reboot
your HT812/HT814 for the new IP address to take Effect.
03
“Subnet” + IP address
Same as menu 02
04
“Gateway” + IP address
Same as menu 02
05
“DNS Server” + IP address
Same as menu 02
07
Preferred Vocoder
Press “9” to move to the next selection in the list:
PCM U / PCM A iLBC G-726 G-723 G-729 OPUS G722
10
“MAC Address”
Announces the MAC address of the unit.
Note: The device has two MAC addresses. One for the WAN port and one for the
LAN port. The device MAC address announced is the address of LAN port.
12
WAN Port Web Access
Press “9” to toggle between enable / disable. Default is disabled.
13
Firmware Server IP Address Announces current Firmware Server IP address. Enter 12-digit new IP address.
14
Configuration Server IP Address
Announces current Config Server Path IP address. Enter 12-digit new IP address.
15
Upgrade Protocol
Upgrade protocol for firmware and configuration update. Press “9” to toggle between TFTP / HTTP / FTP / FTPS or HTTPS. Default is HTTPS.
16
Firmware Version
Announces Firmware version information.
17
Firmware Upgrade
Firmware upgrade mode. Press “9” to toggle among the following three options:
Always check Check when pre/suffix changes Never upgrade
20
“Check Device Individual Certificate Information”
The users can now use the IVR system to obtain specific details about the device’s certificate.
47
“Direct IP Calling”
Enter the target IP address to make a direct IP call, after dial tone. (See “Make a Direct IP Call”.)
86
Voice Mail
Access to your voice mails messages.
99
“RESET”
Press “9” to reboot the device Enter MAC address to restore factory default setting (See Restore Factory Default Setting section)
“Invalid Entry”
Automatically returns to main menu
“Device not registered”
This prompt will be played immediately after off hook If the device is not registered and the option “Outgoing Call without Registration” is in NO
Table 5: Voice Prompt Menu
Five success tips when using the voice prompt
“” shifts down to the next menu option and “#” returns to the main menu “9”
functions as the ENTER key in many cases to confirm or toggle an option. All
entered digit sequences have known lengths 2 digits for menu option and 12
digits for IP address. For IP address, add 0 before the digits if the digits
are less than 3 (i.e. 192.168.0.26 should be key in like 192168000026. No
decimal is needed). Key entry cannot be deleted but the phone may prompt error
once it is detected. Dial 98 to announce the extension number of the port.
Please make sure to reboot the device after changing network settings (IP
Address, Gateway, Subnet…) to apply the new configuration.
Configuration via Web Browser
The HT812/HT814 embedded Web server responds to HTTP GET/POST requests.
Embedded HTML pages allow a user to configure the HT812/HT814 through a web
browser such as Google Chrome, Mozilla Firefox and Microsoft’s IE.
Microsoft Internet Explorer: version 10 or higher. Google Chrome: version
58.0.3 or higher. Mozilla Firefox: version 53.0.2 or higher. Safari: version
5.1.4 or higher. Opera: version 44.0.2 or higher.
Accessing the Web UI
Via WAN port
For the initial setup, the Web access is by default enabled when the device is
using private IP and disabled when using public IP, and you cannot access the
Web UI of your HT812/HT814 until it’s enabled, the following steps will show
you how to enable it via IVR.
1. Power your HT812/HT814 using PSU with the right specifications. 2. Connect
your analog phone to phone ports (FXS) of your HT812/HT814. 3. Press ***
(press the star key three times) to access the IVR menu and wait until you
hear “Enter the menu option “. 4. Press 12, the IVR menu will announce that
the web access is disabled, press 9 to enable it. 5. Reboot your HT812/HT814
to apply the new settings.
Please refer to steps below if your HT812/HT814 is connected via WAN port:
1. You may check your HT812/HT814 IP address using the IVR on the connected
phone.
Please see Obtain the HT812/HT814 IP address via the connected analogue phone
2. Open the web browser on your computer. 3. Enter the HT812/HT814’s IP
address in the address bar of the browser. 4. Enter the administrator’s
password to access the Web Configuration Menu.
Note: The computer must be connected to the same sub-network as the
HT812/HT814. This can be easily done by connecting the computer to the same
hub or switch as the HT812/HT814.
Via LAN port
Please refer to steps below if your HT812/HT814 is connected via LAN port:
1. Power your HT812/HT814 using PSU with the right specifications. 2. Connect
your computer or switch directly to your HT812/HT814 LAN port. 3. Open the web
browser on your computer. 4. Enter the default LAN IP address (192.168.2.1) in
the address bar of the browser. 5. Enter the administrator’s password to
access the Web Configuration Menu. 6. Make sure to reboot your device after
changing your settings to apply the new configuration.
Please make sure that your computer has a valid IP address on the range
192.168.2.x so you can access the web GUI of your HT812/HT814.
Web UI Access Level Management
There are three default passwords for the login page:
User Level End User Level
Password 123
Web Pages Allowed Only Status and Basic Settings
Administrator Level
admin
All pages
Viewer Level
viewer
Only checking. Not allowed to modify content.
The password is case-sensitive and must contain 8-20 characters, at least one number, one uppercase, and one lowercase letter. When changing any settings, always submit them by pressing Update or Apply button at the bottom of the page. After submitting the changes in all the Web GUI pages, if a reboot is required, the web page will prompt the user to reboot by
offering a reboot button on the web page.
Saving the Configuration Changes
After users make changes to the configuration, pressing Update button will
save but not apply the changes until Apply button is clicked. Users can
instead directly press Apply button. When a reboot is required to apply
changes, the web page will prompt the user to reboot by offering a reboot
button on the web page.
Changing Admin Level Password
1. Access your HT812/HT814 web UI by entering its IP address in your favorite
browser. 2. Enter your admin password (default: admin). 3. Press Login to
access your settings. 4. Go to Advanced Settings New Admin Password and enter
the new admin password. 5. Confirm the new admin password. 6. Press Apply at
the bottom of the page to save your new settings.
Figure 7: Admin Level Password
Changing User Level Password
1. Access your HT812/HT814 web UI by entering its IP address in your favorite
browser. 2. Enter your admin password (default: admin). 3. Press Login to
access your settings. 4. Go to Basic Settings New End User Password and enter
the new end-user password. 5. Confirm the new end-user password. 6. Press
Apply at the bottom of the page to save your new settings.
Figure 8: User Level Password
Changing Viewer Password
1. Access your HT812/HT814 web UI by entering its IP address in your favorite
browser. 2. Enter your admin password (default: admin). 3. Press Login to
access your settings. 4. Go to Basic Settings New Viewer Password and enter
the new viewer password. 5. Confirm the new viewer password. 6. Press Apply at
the bottom of the page to save your new settings.
Figure 9: Viewer Level Password
Changing HTTP Web Port
1. Access your HT812/HT814 web UI by entering its IP address in your favorite
browser. 2. Enter your admin password (default: admin). 3. Press Login to
access your settings. 4. Go to Basic Settings HTTP Web Port. 5. Make sure that
the Web Access Mode is set to HTTP. 6. Change the current port to your
desired/new HTTP port. Ports accepted are in range [1-65535]. 7. Press Apply
at the bottom of the page to save your new settings
Figure 10: Web HTTP Port
Web Configuration Pages Definitions
This section describes the options in the HT812/HT814 Web UI. As mentioned,
you can log in as an administrator or an end user.
Status: Displays the system info, network status, account status, and line
options. Basic Settings: Configures the end user level password, IP address
modes, web access, time zone settings and language. Advanced Settings:
Configures networks, upgrading and provisioning, TR-069, security settings,
date and time, syslog, audio settings, call settings and call progress tones.
Profile (1,2): Configures the SIP Server, SIP Registration, NAT settings, call
features, ring tones. FXS Ports: Configures SIP accounts settings, Off hook
Auto-dial.
Status Page Definitions
Status
MAC Address
Shows device ID in hexadecimal format. This is needed by network
administrators for troubleshooting. The MAC address will be used for
provisioning and can be found on the label on original box and on the label
located on the bottom panel of the device.
Note: The device has two MAC addresses, one for the WAN port and one for the
LAN port. The MAC address located on the bottom panel of the device is the MAC
address of LAN port. The MAC address of WAN port is MAC address of LAN port
+1.
Example: MAC Address: WAN “00:0B:82:25:AF:32”, LAN “00:0B:82:25:AF:31”.
WAN IPv4 Address
Displays assigned IPv4 address.
WAN IPv6 Address
Displays assigned IPv6 address.
VPN IPv4 Address
Displays assigned OpenVPN IPv4 address.
VPN IPv6 Address
Displays assigned OpenVPN IPv6 address.
Product Model
Displays product model info. Default is HT812 or HT814.
Hardware Version
Displays the hardware revision information and the part number.
Software version
Program: Specifies Program version. This is the main firmware release number,
which is always used for identifying the software system of the HT812/HT814.
Bootloader: Specifies Boot version.
Core: Specifies Core version.
Base: Specifies Base version.
CPE: Specifies CPE version. CPE version is displayed only when HT812/HT814 is
connected to an ACS using TR-069 protocol.
Software Status
Indicates the current software status of the HT (Running or Stopped).
System Up Time
Indicates actual system time and uptime since last reboot.
CPU Load Indicates CPU load (%)
Network Cable Status
Indicates the Status of the Network cables connected to the LAN Port and the WAN Port. Status (Up/Down), Speed (Mbps), Operational Mode (Full/Half Duplex)
PPPoE Link Up
Indicates PPPoE connection status.
NAT
Indicates type of NAT when it is configured.
Port Status
Displays relevant information regarding the FXS ports about their registration, current status and their appropriate User ID.
Port Options
Displays relevant information regarding the FXS ports about their DND and call forward features.
CDR File
Download, Preview. Or, Delete call history records from the web GUI. Only the last 1000 records will be available.
SIP File
Download, Preview or, Delete locally stored SIP trace. Note: “Send SIP Log” must be enabled to be able to capture the trace.
Provision Displays provisioning status.
Core Dump
Provides generated core dump file if unit malfunctions. Clean will be displayed if no issues.
Basic Settings Page Definitions
Table 6: Status Page Definitions
Basic Settings New End User Password
Confirm End User Password
New Viewer Password
Confirm Viewer Password Web/SSH Access Web Session Timeout Web Access Attempt
Limit Web Lockout Duration
Web Access Mode HTTP Web Port HTTPS Web Port Disable SSH SSH Port SSH Idle
Timeout Disable Telnet Telnet Port
Security Controls for SSH/Telnet Access
Configures user level password. Case sensitive and max. Length of 20
characters. Note : The new Password must contain 8-20 characters, at least one
number, one uppercase, and a lowercase letter. Purposely not displayed for
security reasons.
Re-enter the end user password to confirm change user password on web GUI to
avoid typo or mistakes.
Configures viewer-level password. Case sensitive and max. length of 20
characters. Note : The new Password must contain 8-20 characters, at least one
number, one uppercase, and a lowercase letter. Purposely not displayed for
security reasons.
Re-enter the viewer password to confirm change viewer password on web GUI to
avoid typo or mistakes.
Configure timer to logout web session during idle. Default is 10 min. Range is
2-60 min.
Configure attempt limit before lockout. Default is 5. Range is 1-10.
If login attempt failed 5 times, login would be locked out for the time
length. (Default 15 mins. Range 1-15 min).
Allows users to choose the Web Access Mode between “HTTPS”, “HTTP” and
“Disabled”. If “Disabled” is selected, web UI access will be disabled. By
default, “HTTP” is selected.
Customizes HTTP port used to access the HT801/HT802 web UI. Default is 80.
Customizes HTTPS port used to access the HT801/HT802 web UI. Default is 443.
Enables/disables the SSH access. Default is No (enabled).
Allows users to self-configure SSH Port number. By default, the port number is
22.
Configures SSH session timeout. [0 86400] seconds; Default is 0.
Enables/disables the Telnet access. Default is Yes (disabled).
Allows users to self-configure Telnet Port number. By default, the port number
is 23.
Allows the user to choose the security control for SSH or Telnet Access, the
options can be : 1. Only allow SSH private IP users to set system Pvalue. 2.
Allow all SSH users to set system Pvalue. 3. Allow all SSH users to set any
Pvalue. 4. Allow any user to set any Pvalue. 5. Prohibit setting Pvalue. By
default , it is set to “Allow any user to set any Pvalue”.
WAN Side Web/SSH Access Whitelist for WAN Side Blacklist for WAN Side Internet Protocol IPv4 Address Dynamically assigned via DHCP
Enables / Disables the Web and SSH access through the WAN port. The available
options are the following:
No: No access to the web or SSH from any IP address on the WAN side. Yes:
Access for the Web GUI and SSH is enabled on the WAN side. Auto: Only private
IP could access the web or SSH on the WAN side. Default setting is Auto.
Users can configure the whitelist for WAN Side to be used for remote
management.
Multiple IPs are supported and need to be separated by “space”. Example:
192.168.5.222 192.168.5.223 192.168.7.0/24 Note: If both blacklist and
whitelist are not empty, the blacklist is processed first, followed by the
whitelist.
Users can configure the blacklist for WAN Side to ban WAN side web access.
Multiple IPs are supported and need to be separated by “space”. Example:
192.168.5.222 192.168.5.223 192.168.7.0/24 Note: If both blacklist and
whitelist are not empty, the blacklist is processed first, followed by the
whitelist.
Selects one of the following IP protocol modes:
IPv4 Only: Enforce IPv4 protocol only. IPv6 Only: Enforce IPv6 protocol only.
Both, Prefer IPv4: Enable both IPv4 and IPv6 and prefer IPv4. Both, prefer
IPv6: Enable both IPv4 and IPv6 and prefer IPv6. Note: Make sure to reboot the
phone for the changes to take effect.
Allows users to configure the appropriate network settings on the HT80x to
obtain IPv4 address. Users could select “DHCP”, “Static IP” or “PPPoE”. By
default, it is set to “DHCP”.
All the field values for the static IP mode are not used (even though they are
still saved in the flash memory.) The HT801/802 acquires its IP address from
the first DHCP server it discovers from the LAN it is connected.
DHCP hostname: Specifies the name of the client. The name may or may not be
qualified with the local domain name. This field is optional but may be
required by ISP.
DHCP domain name: Specifies the domain name that client should use when
resolving hostname via the Domain Name System.
DHCP vendor class ID: Exchanges vendor class ID by clients and servers to
convey particular configuration or other identification information about a
client. Default is HT8XX.
Use PPPoE
Set the PPPoE account settings. If selected, ATA attempt to establish a PPPoE
session if any of the PPPoE fields is set.
PPPoE account ID: Defines the PPPoE username. Necessary if ISP requires you to
use a PPPoE (Point to Point Protocol over Ethernet) connection.
PPPoE password: Specifies the PPPoE account password. PPPoE Service Name:
Defines PPPoE service name. If your ISP uses a service name for
the PPPoE connection, enter the service name here. This field is optional.
Default is blank.
Preferred DNS server Statically configured as IP address
IPv6 Address
Specifies preferred DNS server to use when DHCP or PPPoE are set.
Configure IP address, subnet Mask, default router IP address, 1st preferred
DNS server, 2nd preferred DNS server. These fields are set to zero by default.
Allows users to configure the appropriate network settings on the HT80x to
obtain IPv6 address. Users could select “DHCP”, “Static IP”. By default, it is
set to “DHCP”.
DHCP mode: all the field values for the static IP mode are not used (even
though they are still saved in the flash memory.) The HT801/HT802 acquires its
IP address from the first DHCP server it discovers from the LAN it is
connected.
Static IP mode: configure IP address, 1st and 2nd DNS server, preferred DNS
server. These fields are set to zero by default.
Full Static: When enabling the option full static, users need to specify the
Static IPv6 and the IPv6 Prefix length.
Prefix Static: When enabling the option prefix static, users need to specify
the IPv6 Prefix (64 bits).
Enable Management Interface
Allows administrator to setup a Virtual Network Interface on top of the physical interface for device management. Default is No.
Management Access
Chooses whether to access using “Management Interface Only” (Default) Or “Both Service and Management Interfaces”
Enable SNMP Through Management Interface
This feature allows users to route SNMP packets through management interface. Default setting is No.
Enable TR-069 Through Management Interface
This feature allows users to route TR-069 packets through the management interface. Default setting is No.
Enable Syslog Through Management Interface
This feature allows users to route Syslog packets through the management interface. Default setting is No.
Management Interface IPv4 Address
Configures Voice VLAN Type : Default is dynamically assigned via DHCP Or, statically configured as:
IP Address : Default is 192.168.100.100 Subnet Mask : Default is 255.255.255.0
Default Router : Default is 192.168.100.1 DNS Server 1 : Default is 0.0.0.0
DNS Server 2 : Default is 0.0.0.0
802.1Q/VLAN Tag vlan tagging : [0 4094]; Default is 0
802.1p priority value : priority : [0 7]; Default is 0
Time Zone
Selects time zone to define date/time on the device.
Self-Defined Time Zone
Allows users to define their own time zone.
Allow DHCP server to set Time Zone
Obtains time zone setting (offset) from a DHCP server using DHCP Option 2; it will override selected time zone. If set to “No”, the analogue adapter will use selected time zone even if provided by DHCP server. The Default setting is Yes.
Language
Configures the languages of the voice prompt and web interface, except Spanish that it is only in IVR. Available languages: English, Chinese, Traditional Chinese, Russian, Spanish IVR.
NAT/DHCP Server Information & Configuration
Device Mode
Controls whether the device is working in NAT router mode or Bridge mode. Save the setting and reboot prior to configuring the HT812/HT814.
NAT maximum ports
Defines the number of ports that can be managed while in NAT router mode. Range: 0 4096, default is 1024. Typically, one port per connection.
NAT TCP timeout
NAT TCP idle timeout in seconds. Connection will be closed after preconfigured, timeout if not refreshed. Range: 0 3600
NAT UDP timeout
NAT TCP idle timeout in seconds. Connection will be closed after preconfigured, timeout if not refreshed. Range: 0 3600, default is 300
Uplink bandwidth
Specifies the maximum uplink bandwidth permitted by the device. This function is disabled by default. The total bandwidth can be set as: 128K, 256K, 512K, 1M, 2M, 3M, 4M, 5M, 10M or 15M. The primary function of this setting is to limit the uplink bandwidth for the device internal system, signaling and NATed traffic. Example: When 512k is configured, there will be at least 512kbps limited for internal system, signaling and NATed traffic. Voice or RTP stream will never be limited.
Downlink bandwidth
Specifies the maximum downlink bandwidth permitted by the device. This function is disabled by default. The total bandwidth can be set as: 128K, 256K, 512K, 1M, 2M, 3M, 4M, 5M, 10M or 15M. The primary function of this setting is to limit the download bandwidth for the device internal system, signaling and NATed traffic. Example: if 128 is configured, there will be at least 128kbps limited for internal system, signaling and NATed traffic. Voice or RTP stream will never be limited.
Enable UPnP support
When set to “Yes”, the HT812/HT814 acts as an UPnP gateway for your UPnP enabled applications. UPnP = “Universal Plug and Play”
Reply to ICMP on WAN port
Default is No. When set to “Yes”, the HT812/HT814 responds to the PING command from other computers, but is also made vulnerable to DOS attacks.
Cloned WAN MAC Addr
This allows the user to change/set a specific MAC address on the WAN interface. Note: Set in Hex format
LAN Port VLAN Feature Under Bridge Mode
Allows users to configure the customized VLAN tag and priority value under switch mode. VLAN Tag range is 0-4094, the Priority Vlaue range is 0-7. The Default for both is 0
Enable LAN DHCP
When set to “Yes”, device will function as a simple router and LAN port will provide IP addresses to internal network. Connect the WAN port to ADSL/Cable modem or any other equipment that provides access to public Internet
LAN DHCP Base IP
Base IP Address for a LAN port. Default factory setting is 192.168.2.1. Note: When the device detects WAN IP is conflicting with LAN IP, the LAN base IP address will be changed based on the network mask — the effective subnet will be increased by 1. For example; 192.168.2.1 will be changed to 192.168.3.1 if net mask is 255.255.255.0. Then the device will reboot
LAN DHCP Start IP
Default value is 100. The last segment of IP address assigned to the HT812/HT814 in the LAN Network. Default configuration assigns IP address (to local network devices) starting from 192.168.2.100.
LAN DHCP End IP
Default value is 199. This parameter allows a user to limit the number of local network devices connected to the internal router. Default configuration assigns IP address (to devices connected to the LAN port) in a range from 192.168.2.100 up to 192.168.2.199.
LAN Subnet Mask
Sets the LAN subnet mask. Default value is 255.255.255.0
DHCP IP Lease Time DMZ IP Port Forwarding
Reset Type
Default value is 120 hrs (5 days). The length of time the IP address is
assigned to the LAN clients. Value is set in units of hours.
This function forwards all WAN IP traffic to a specific IP address if no
matching port is used by HT812/HT814 or in the defined port forwarding.
Forwards a matching (TCP/UDP) port to a specific LAN IP address with a
specific (TCP/UDP) port. Up to 8 rules are available.
Gives the administrator the option to restore default configuration on the
HT801/HT802. There are 3 types of factory reset:
ISP Data Reset: All ISP (Internet Service Provider) configuration which may
affect the IP address will be reseted (including WAN static IP).
VOIP Data Reset: All VoIP related configuration (mainly everything located on
FXS page).
Full Reset: Both VoIP and ISP related configuration at the same time. Note:
After you choose the reset type, you must click the reset button to take
effect.
Table 7: Basic Settings Page
Advanced Settings Page Definitions
New Admin Password
Defines the administrator level password to access the Advanced Web Configuration page. This field is case sensitive. Only the administrator can configure the “Advanced Settings” page. Password field is purposely left blank for security reasons after clicking update and saved. Note : The new Password must contain 8-20 characters, at least one number, one uppercase, and a lowercase letter. Purposely not displayed for security reasons
Confirm Admin Password
Confirms the new admin password.
Disable User Level Web Access
Disable or enable User Level Web Access. Default is No.
Disable Viewer Level Web Access
Disable or enable Viewer Level Web Access Default is No.
Layer 2 QoS
Sets values for 802.1Q/VLAN Tag. Default is 0. Valid range is 0-4094. SIP 802.1p. Default is 0. Valid range is 0-7. RTP 802.1p. Default is 0. Valid range is 0-7.
Blacklist for WAN Side Port
It could be either port range or single port separated by a “,” Example: “5000-6000, 7000 “.
STUN Server is
Configures IP address or domain name of STUN server. Only non-symmetric NAT routers work with STUN.
Keep-alive interval
Sends periodically a blank UDP packet to SIP server to keep the “ping hole” on the NAT router open. Default is 20 seconds.
Use STUN to detect network connectivity
Uses STUN keep-alive to detect WAN side network problems. If keep-alive request does not yield any response for configured number of times (minimum 3), the device will restart the TCP/IP stack. If the STUN server does not respond when the device boots up, the feature is disabled. Default setting is No.
Use DNS to detect network connectivity
Uses DNS to detect WAN side network problems. Default setting is “No”.
Use ARP to detect network connectivity
Uses ARP to check the network connectivity. Default is “Yes”.
Verify host when using HTTPS
Enables / disables the host verification when using HTTPS.
Upgrade via
Selects firmware upgrade/provisioning method: TFTP, HTTP, HTTPS, FTP or FTPS. Default is HTTPS.
Provision and upgrade to new Gen2 certificate
Configures whether or not to upgrade to a new Gen-2 certificate, It is set to no upgrade by Default.
Firmware Server Path
Config Server Path
XML Config File Password HTTP/HTTPS FTP/FTPS Username
Sets IP address or FQDN of firmware server. The URL of the server that hosts
the firmware release. Note: You can specify the protocol used in the Firmware
Server Path. (example: https://192.168.5.120), this will bypass the “Upgrade
Via” method. Default is fm.grandstream.com/gs.
Sets IP address or FQDN of configuration server. The URL of the server that
hosts the configuration file to provision HT8xx. Note: You can specify the
protocol used in the Config Server Path. (example: https://192.168.5.120),
this will bypass the “Upgrade Via” method. Default is fm.grandstream.com/gs.
Decrypts XML configuration file when encrypted. The password used for
encrypting the XML configuration file using OpenSSL.
Enters username to authenticate with HTTP/HTTPS FTP/FTPS server.
HTTP/HTTPS FTP/FTPS Password Enters password to authenticate with HTTP/HTTPS FTP/FTPS server.
Firmware File Prefix
Checks if firmware file is with matching prefix before downloading it. This field enables user to store different versions of firmware files in one directory on the firmware server.
Firmware File Postfix
Checks if firmware file is with matching postfix before downloading it. This field enables user to store different versions of firmware files in one directory on the firmware server.
Config File Prefix
Checks if configuration files are with matching prefix before downloading them. This field enables user to store different configuration files in one directory on the provisioning server.
Config File Postfix
Checks if configuration files are with matching postfix before downloading them. This field enables user to store different configuration files in one directory on the provisioning server.
Enable using tags in URL
Allows users to configure variables on the configuration server path to differentiate the directories on the server.
Always send HTTP Basic Authentication Information
Default is No. If set to Yes, The device will send configured user name and password within HTTP request before server sends authentication challenge.
Allow DHCP Option 66 or 160 to Override Server
Obtains configuration and upgrade server’s information using options 66 from DHCP server. Note: If DHCP Option 66 is enabled, the HT8xx will attempt downloading the firmware file from the server URL provided by DHCP, even though Config Server Path is left blank. The server URL provided by DHCP can include authentication credentials using following format: “username:password@Provisioning_Server_IP”.
Additional Override DHCP Option
Allows users to enable the Additional Override DHCP Option in Option 150. The default value is “None”.
3CX Auto Provision
Sends multicast “SUBSCRIBE” message for provisioning at booting stage, used for PnP (Plugand-Play) configuration. Default is Yes.
Automatic Upgrade
Specifies when the firmware upgrade process will be initiated; there are 4 options: No: The HT8xx will only do an upgrade once at boot up. Check every X minutes: User needs to specify a period in minutes. Check every day: User needs to specify the start hour and the end hour of the day (0-23). Check every week: User needs to specify “Day of the week (0-6)”. (Day of week is starting from Sunday). Default is No.
Randomized Automatic Upgrade
Randomized Automatic Upgrade within the range of hours of the day or postpone the upgrade every X minute(s) by random 1 to X minute(s).
Always Check for New Firmware at Boot up
Configures the HT8xx to always search for the new firmware at boot up. During the boot stage, the HT8xx will contact the firmware upgrade server to search for a new firmware, when available it will start the upgrade process, otherwise it will boot normally.
Check New Firmware only when F/W pre/suffix changes
Configure the HT8xx to search for the new firmware when the firmware prefix / suffix changes. When this option is selected, the HT8xx will check for updates only when the pre/suffix has been changed.
Always Skip the Firmware Check
Configures the HT8xxto skip the firmware check, when this option is selected the HT8xx will always skip searching for a new firmware.
Configuration File Types Allowed
Allows users to configure provision configuration file type in xml file only or all file types.
Download and Process All Available Config Files
This feature allows users to download and process all available config files. By default, the device will provision the first available config in the order of cfgMAC > cfgMAC.xml > cfgMODEL.xml > and cfg.xml (corresponding to device- specific, model-specific, and global configs). If this option is enabled, the device will inverse the downloading process to cfg.xml > cfgMODEL.xml > cfgMAC.bin > cfgMAC.xml and add cfgMAC_override.xml. The following files will override the files that have already been loaded and processed. The default value is “No”
Disable SIP NOTIFY Authentication
Disables the SIP NOTIFY Authentication on the phone adapter. If set to “Yes”, the phone adapter will not challenge NOTIFY with 401. The default setting is “No”
Authenticate Conf File
Authenticates configuration before being accepted. This protects the configuration from unauthorized modifications. Default is No.
Validate Server Certificates
This feature allows users to validate server certificates with our trusted list of TLS connections. The device needs to reboot after changing the setting. Default is enabled.
Trusted CA certificates A
Uses the certificate for Authentication if “Check Domain Certificates” is set to “Yes” under “Account”> “SIP Settings”.
Trusted CA certificates B
Uses the certificate for Authentication if “Check Domain Certificates” is set to “Yes” under “Account”> “SIP Settings”.
Load CA Certificates
This feature allows user to specify which certificate to trust when performing server authentication. Build-in trusted : (Default) Build-in trusted certificates Custom trusted certificate: Uploaded Certificates
Root CA Version
SIP TLS Certificate
SIP TLS Private Key SIP TLS Private Key Password Custom Certificate (Private
Key + Certificate) Gen-2 EC private key
All trusted Certificates: Both built-in and uploaded Certificates
Configures the Root CA version. can be set to either Current root or new root.
Default Value is New Root.
Specifies SSL certificate used for SIP over TLS is in X.509 format. The HT8xx
has built-in private key and SSL certificate. Maximum supported length is
4069.
Specifies TLS private key used for SIP over TLS is in X.509 format. Maximum
supported length is 4069.
Specifies SSL Private key password used for SIP Transport in TLS/TCP.
Allows users to update to the device their own certificate signed by a custom
CA certificate to manage client authentication.
Configures the Gen-2 Elliptic Curve Private Key. based on RFC 5915. The Max
value length is 8192 characters.
Enable TR-069
TR-069 firewall rules
ACS URL
ACS Username ACS Password Periodic Inform Enable Periodic Inform Interval
Connection Request Username Connection Request Password Connection Request
Port CPE SSL Certificate CPE SSL Private Key Enable SNMP SNMP Version SNMP
Port SNMP Trap IP Address SNMP Trap port SNMP Trap Version SNMP Trap Interval
SNMPv1/v2c Community SNMPv1/v2c Trap Community SNMPv3 Username
SNMPv3 Security Level
SNMPv3 Authentication Protocol SNMPv3 Privacy Protocol SNMPv3 Authentication
Key SNMPv3 Privacy Key
Sets the phone adapter system to enable the “CPE WAN Management Protocol”
(TR-069). Default setting is Yes. Note: New Parameters were added to the TR069
Data model starting from Firmware version 1.0.47.4 Configures the TR-069
firewall rules , Value port range is 1-65535
Specifies URL of TR-069 Auto Configuration Servers (e.g.,
http://acs.mycompany.com), or IP address. Default setting is:
“https://acs.gdms.cloud” Enters username to authenticate to ACS.
Enters password to authenticate to ACS. Sends periodic inform packets to ACS.
Default is Yes.
Sets frequency that the inform packets will be sent out to ACS. Default is
86400 seconds.
Enters username for ACS to connect to the HT8xx. Enters password for ACS to
connect to the HT8xx.
Configures the TR-069 connection request port. The value range is 0 to
65535.Default is 7547 Configures the Cert File for the phone adapter to
connect to the ACS via SSL.
Specifies the Cert Key for the phone adapter to connect to the ACS via SSL.
Default is No.
Choose between (Version 1, Version 2c, or Version 3). Listening Port of SNMP
daemon (Default 161).
IP address of trap destination. Up to 3 trap destinations are supported. Users
should enter the IP addresses separated with comma (,).
Port of Trap destination (Default 162) Choose between (Version 1, Version 2c,
or Version 3).
Time interval between traps (Default is 5). Name of SNMPv1/v2c community.
Name of SNMPv1/v2c trap community. Username for SNMPv3.
noAuthUser: Users with security level noAuthnoPriv and context name as noAuth.
authUser: Users with security level authNoPriv and context name as auth.
privUser: Users with security level authPriv and context name as priv. Select
the Authentication Protocol: “None” or “MD5” or “SHA.”
Select the Privacy Protocol: “None” or “AES/AES128” or “DES”. Enter the
Authentication Key.
Enter the Privacy Key.
SNMPv3 Trap Username
Username for SNMPv3 Trap.
SNMPv3 Trap Security Level
noAuthUser: Users with security level noAuthnoPriv and context name as noAuth. authUser: Users with security level authNoPriv and context name as auth. privUser: Users with security level authPriv and context name as priv.
SNMPv3 Trap Authentication Protocol
Select the Authentication Protocol: “None” or “MD5” or “SHA”.
SNMPv3 Trap Privacy Protocol
Select the Privacy Protocol: “None” or “AES/AES128” or “DES”.
SNMPv3 Trap Authentication Key
Enter the Trap Authentication Key.
SNMPv3 Trap Privacy Key
Enter the Trap Privacy Key.
Enable RADIUS Web Access Control
Default is No.
Action upon RADIUS Auth Server Error
Choose action upon RADIUS server error. Default is Authenticate Locally (Default Authenticate Locally)
RADIUS Auth Server Address
Address of RADIUS Auth server.
RADIUS Auth Server Port
Port of RADIUS Auth server.
RADIUS Shared Secret
Set RADIUS shared secret.
RADIUS VSA Vendor ID
Configure RADIUS VSA Vendor ID to match RADIUS server’s configuration. Default is 42397 for Grandstream Networks Inc.
RADIUS VSA Access Level Attribute
Configure RADIUS VSA Access Level Attribute to match RADIUS server’s configuration. Incorrect setting would cause Radius authenticate fail.
Enable DDNS
Allow users to use DDNS.
DDNS Server
Selects DDNS Server: dyndns, freedns.afraid.org, zoneedit.com, no-ip.com, oray.net. Default is dyndns.
DDNS Username
64 characters as Max String Length.
DDNS Password
64 characters as Max String Length.
DDNS Hostname
64 characters as Max String Length.
DDNS Hash
64 characters as Max String Length.
Enable OpenVPN®
Allow user to enable OpenVPN®. Default is No.
OpenVPN® Server Address
Specify the IP address or FQDN for the OpenVPN® Server.
OpenVPN® Port
Specify the listening port of the OpenVPN® server. Default is 1194
OpenVPN® Interface type
Specify the Interface type of OpenVPN® whether TAP or TUN. Default is TUN.
OpenVPN® Transport
Specify the Transport Type of OpenVPN® whether UDP or TCP. The default is UDP.
Enable OpenVPN® LZO Compression
Enable OpenVPN® LZO Compression. Default is Yes.
OpenVPN® Encryption
Select the OpenVPN® Encryption. Default is BF-CBC 128 bit (default key).
OpenVPN® Digest
Select the OpenVPN® Digest. Default is SHA1.
OpenVPN® CA
Specifies the OpenVPN® CA. Maximum Character Number is 8192.
OpenVPN® Certificate
Specifies the OpenVPN® Certificate. Maximum Character Number is 8192.
OpenVPN® Client Key
Specifies the Client Key. Maximum Character Number is 8192.
OpenVPN® Client Key Password
Configures the OpenVPN® Client Key Password. Maximum Length is 64.
OpenVPN® username
Configure the OpenVPN® username.
OpenVPN® password
Configure the OpenVPN® password
System Ring Cadence
Configuration option is set ring cadence on FXS port for all incoming calls. Syntax: c=on1/off1-on2/off2-on3/off3; (3 cadences maximum) Default is set to c=2000/4000; (US standards)
Call Progress Tones: Dial Tone Ringback Tone Busy Tone
Using these settings, users can configure tone frequencies and cadence according to their preference. By default, they are set to North American frequencies. Configure these settings with known values to avoid uncomfortable high pitch sounds. ON is the period of ringing (“On time” in `ms’) while OFF is the period of silence. In order to set a
Reorder Tone Confirmation Tone Call Waiting Tone Prompt Tone Conference Party Hangup Tone * Special Proceed Indication Tone Special Condition Tone
continuous tone, OFF should be zero. Otherwise, it will ring ON ms and a pause
of OFF ms and then repeat the pattern. Example configuration for N.A. Dial
tone: f1=350@-13, f2=440@-13, c=0/0; Syntax: f1=freq@vol, f2=freq@vol,
c=on1/off1-on2/off2-on3/off3; […] (Note: freq: 0 4000Hz; vol: -30 0dBm) *
“Conference Party Hang-up Tone” will apply only if the “Special Feature” is
set to “MTS”. Special Proceed Indication Tone: This feature allows user to
configure the tone played when user goes offhook and there is voicemail on the
subscribed mailbox. Need to set MWI Tone’ to
Special Proceed Indication
Tone’ to use this feature.
Prompt Tone Access Code
Key pattern to get Prompt Tone. Maximum 20 digits.
Lock Keypad Update
Configuration update via keypad (analog phone connected to FXS port keypad using IVR menu) is disabled if set to Yes.
Disable Voice Prompt
Voice prompt is disabled if set to Yes.
Disable Direct IP Call
Direct IP call is disabled if set to Yes.
Play Busy Tone When Account is unregistered
When this feature is set to Yes, device will play busy tone when the FXS port account is not registered, and the attached analog phone is offhook.
Blacklist for Incoming Calls
Allow users to block incoming calls from specific list of numbers. Maximum
allow 10 SIP numbers and each number should be separated by a comma (,’) in web UI. Other allowed characters are 0-9, comma (“,”), asterisk (
*’), pound
sign (#’) and plus sign (
+’).
NTP Server
Defines the URL or IP address of the NTP server. The ATA may obtain the date and time from the server. The default setting is “pool.ntp.org.”
Allow DHCP Option 42 to override NTP server
Defines whether DHCP Option 42 should override NTP server or not. When enabled, DHCP Option 42 will override the NTP server if it is set up on the LAN. The default setting is Yes.
DHCP Option 17 Enterprise Number
Configure the DHCP option 17 number. Default is 3561
CDR File Option
By default, the device will split the allowed memory for CDR file into 2 parts. Device will create the first CDR file which is half of the allowed size, when it is full, device will create the second file. When “CDR File Option” is set to Default “Keep”, device will keep the call records when both files are full, no more new record will be stored. When this feature is set to “Overwrite”, device will clear the first CDR file and start storing again. When the feature is disabled the device will not record any calls. The CDR file output will be available at Status page: [CDR File]
SIP File Option
By default, the device will split the allowed memory for SIP file into 2 parts. Device will create the first SIP file which is half of the allowed size, when it is full, device will create the second file. When “SIP File Option” is set to Default “Keep”, device will keep the call records when both files are full, no more new record will be stored. When this feature is set to “Overwrite”, device will clear the first SIP file and start storing again. The SIP file output will be available at Status page: [SIP File] Note: “Send SIP Log” must be enabled to be able to capture the trace.
Disable Weak TLS Cipher Suites
Allows users to disable weak ciphers DES/3DES and RC4, Symmetric Encryption SEED, Symmetric Authentication MD5, Protocol Version SSLv2/SSLv3 or Disable All of the Above Weak TLS Ciphers Suites. Default is No.
Minimum TLS Version
This feature allows customer to choose desired Minimum TLS Version. Choices are: Unlimited TLS 1.0 TLS 1.1 TLS 1.2 Default is Unlimited.
Maximum TLS Version
This feature allows customer to choose desired Maximum TLS Version. Choices are: Unlimited TLS 1.0 TLS 1.1 TLS 1.2 Default is Unlimited.
Syslog Protocol
If set to SSL/TLS, the syslog messages will be sent through secured TLS Protocol to syslog server. Default setting is UDP. Note: The CA certificate is required to connect with the TLS server A reboot is required to take effect.
Syslog Server
URL or IP address of syslog server. Note: A reboot is required to take effect.
Syslog Level
Select the HT8xx to report the log level. Default is NONE. The level is one of EXTRA DEBUG, DEBUG, INFO, WARNING or ERROR. Syslog messages are sent based on the following events: 1. product model/version on boot up (INFO level)
Send SIP Log
With Secret Key Information
Information Capture Always Send HTTP Basic Authentication Information
Automatic Reboot
Download Device Configuration Download Device XML Configuration
Upload Firmware
Upload Configuration
Export Backup Configuration
Restore From Backup Configuration E911/HELD Protocol: Enable E911 HELD
Protocol HELD Synchronization Interval Location Server Location Server
Username Location Server Password Secondary Location Server Secondary Location
Server Username Secondary Location Server Password HELD Location Types HELD
NAI HELD Identity 1-10 HELD Identity 1-10 Value E911 Emergency Numbers
Geolocation-Routing Header
2. NAT related info (INFO level) 3. sent or received SIP message (DEBUG
level) 4. SIP message summary (INFO level) 5. inbound and outbound calls (INFO
level) 6. registration status change (INFO level) 7. negotiated codec (INFO
level) 8. Ethernet link up (INFO level) 9. SLIC chip exception (WARNING and
ERROR levels) 10. memory exception (ERROR level) extra syslog style (EXTRA
DEBUG level) Note: A reboot is required to take effect.
Configures whether the SIP log will be included in the syslog messages. The
default setting is No.
Allows users to make packet capture including the secret key to decrypt the
captured TLS packets. Default value is No.
Allows the user to start the Information capture process, which can be enabled
with a reboot option every day at a specific time or disabled, Disabled by
default.
If set to Yes, the device will send configured username and password within
HTTP request without server sending authentication challenge.
Default is No. When “Yes, reboot every day at hour” or “Yes, reboot every week
at day” or “Yes, reboot every month at day” is checked, user can specify “Hour
of the day (0-23)” or “Day of the week (0-6)” or “Day of the month (0-30)”.
Default time is Monday 1AM.
Press Download button to download device configuration file to local computer.
The filename is “config.txt”. The file is plain text and not including
password fields.
Press Download to download device configuration file to local computer. The
filename is “config.xml”. The file will not include password fields.
Press Upload from local directory button to load the firmware file to the
device from your computer. The firmware filename should be “ht80xfw.bin”
(ht802fw.bin for HT802 for instance), “ht81xfw.bin” for HT812/HT814 or
“ht818fw.bin” for HT818.
Press Upload from local directory button to load configuration file to the
device from your computer. The configuration file should be an XML file (for
instance: “config.xml”). Note: The field is not mandatory in the document but
if available only device with specified MAC address will accept the
configuration file.
Press Download button to export device backup configuration to computer. The
output is “cfg
Press Upload button to restore device configuration from previously exported
backup configuration.
Enable Enhanced 911 call. Default is disabled
Configure HELD transfer protocol. HTTP or HTTPS
The valid synchronization interval is between 30 to 1440 minutes. The
synchronization is off when the interval is 0.
Configure the primary Location Information Server (LIS) address
Configure the user name of the primary Location Information Server (LIS)
Configure the password of the primary Location Information Server (LIS)
Configure the seconary Location Information Server (LIS) address
Configure the user name of the secondary Location Information Server (LIS)
Configure the password of the secondary Location Information Server (LIS)
Configure “locationType” element in the location request. “geodetic”, “civic”
and “location URI”
Configure “locationType” element in the location request. “geodetic”, “civic”
and “location URI”
HELD Identity
HELD Identity value
A user can configure multiple emergency numbers separated with the delimiter
symbol “;”.
If “Yes”, E.911 INVITE message includes the “Geolocation-Routing” header with
the value “Yes”
Priority Header
If “Yes”, E.911 INVITE message includes the “Priority” header with the value “emergency”
Profiles Pages Definitions
Profiles (1,2)
Profile Active
Activates / Deactivates the accounts. The FXS port configuration will not change if disabled, although the port will not be operational, in this state, there will be no dial tone when picking up the analog phone and making/receiving calls will not be possible.
Primary SIP Server
Configures SIP server IP address (Supports both IPv4 and IPv6 addresses) or domain name provided by VoIP service provider. (For example: sip.mycompany.com, IPv4:192.168.5.170, or IPv6: fe80::20b:82ff:fe75:211d). This is the primary SIP server used to send/receive SIP messages from/to HT81x.
Failover SIP Server
Defines failover SIP server IP address (Supports both IPv4 and IPv6 addresses) or domain name provided by VoIP service provider. (For example: sip.mycompany.com, IPv4:192.168.5.170, or IPv6 fe80::20b:82ff:fe75:211d:). This server will be used if primary SIP server becomes unavailable.
Prefer Primary SIP Server
Selects to prefer primary SIP server. The account will register to primary Server if registration with Failover server expires. Default is No.
Outbound Proxy
Specifies IP address (Supports both IPv4 and IPv6 addresses) or domain name of outbound Proxy, or media gateway, or session border controller. (For example: proxy.myprovider.com, IPv4: 192.168.5.170, or IPv6: fe80::20b:82ff:fe75:211d). It’s Used by HT818 for firewall or NAT penetration in different network environments. If symmetric NAT is detected, STUN will not work and only outbound proxy can correct the problem
Backup Outbound Proxy
Configures the backup outbound proxy to be used when the “Outbound Proxy” registration fails. (For example: proxy.myprovider.com, or IP address, if any: IPv4: 192.168.5.170/ IPv6: fe80::20b:82ff:fe75:211d). By default, this field is left empty.
Prefer Primary Outbound Proxy
If the user configures this option to “Yes”, when the registration expires, the device will re-register via primary outbound proxy. By default, this option is disabled.
From Domain
allows users to add the actual domain name, it will override the from header.This is an optional configuration.
Allow DHCP Option 120 (override SIP Server)
Configures the HT81x to collect SIP server address from DHCP option 120. Default is No.
SIP transport
Selects transport protocol for SIP packets; UDP or TCP or TLS. Please make sure your SIP Server or network environment supports SIP over the selected transport method. Default is UDP.
SIP URI Scheme When Using TLS
Specifies if “sip” or “sips” will be used when TLS/TCP is selected for SIP Transport. The default setting is “sips”.
Use Actual Ephemeral Port in Contact with TCP/TLS
Controls the port information in the Via header and Contact header. If set to “No”, these port numbers will use the permanent listening port on the phone. Otherwise, they will use the ephemeral port for the connection. Default is No.
NAT Traversal
Indicates type of NAT for each account. This parameter configures whether the NAT traversal mechanism is activated. Users could select the mechanism from No, Keep-alive, STUN, UPnP. Default setting is No.
DNS Mode
Selects DNS mode to use for the client to look up server. One mode can be chosen. A Record (Default): resolves IP Address of target according to domain name. SRV: DNS SRV resource records indicate how to find services for various protocols. NAPTR/SRV: Naming Authority Pointer according to RFC 2915. Use Configured IP: If the SIP server is configured as domain name, device will not send DNS queries, but will use “Primary IP” or “Backup IP” to send SIP message if at least one of them is not empty. It will try to use “Primary IP” first, after 3 tries without any response, it will switch to “Backup IP 1”, then “Backup IP 2”, and then it will switch back to “Primary IP” after 3 retries.
DNS SRV use Registered IP
When the HT81x is registered using the second SRV record, making an outbound call, it will try the second SRV (registered IP) first. By default, this option is disabled and the DNS SRV will use first SRV instead of the registered IP.
DNS SRV Failover Mode
Configure the preferred IP mode when DNS Mode is SRV or NAPTR/SRV. · Default SIP request will always be sent to the address with the top priority based on the SRV query result, even if this address is different from the registered IP address. · Saved one until DNS TTL SIP request will always be sent to the registered IP address until DNS TTL expires or registered IP address is unreachable · Saved on until no response SIP request will always be sent to the registered IP address only until registered IP address is unreachable.
Failback Timer
When the primary SBC is up, device will send SIP requests to the primary SBC. If at any point device fails over to the secondary SBC, the SIP requests will stay on the failover SBC for the duration of the failback timer. When the timer expires, device will send SIP requests to the primary SBC, (in minutes. Default is 60 minutes, max 45 days).
Register before DNS SRV Failover
This feature is used to control whether the device need to initiate a new registration request (following existing DNS SRV fail-over mode) first and then direct the non-registration SIP request (INVITE) to the new successfully registered server or not.
TEL URI
Indicates E.164 number in “From” header by adding “User=Phone” parameter or using “Tel:” in SIP packets, if the HT81x has an assigned PSTN Number. Disabled: Use “SIP User ID” information in the Request-Line and “From” header.
User=Phone: “User=Phone” parameter will be attached to the Request-Line and “From” header in the SIP request to indicate the E.164 number. If set to “Enable”. Enabled: “Tel:” will be used instead of “sip:” in the SIP request. Please consult your carrier before changing this parameter. Default is Disabled.
Use Request Routing ID in SIP INVITE Header
If set to Yes, device will use the configured [Request URI Routing ID] in the SIP INVITE. This option is usually used under a SIP trunk account’s configuration. Default is No.
SIP Registration
Controls whether the HT81x needs to send REGISTER messages to the proxy server. Default setting is Yes.
Unregister on Reboot
Controls whether to clear SIP user’s information by sending un-register
request to the proxy server. The unregistration is performed by sending a
REGISTER message with “Expires=0” parameter to the SIP server. This will
unregister the SIP account under the concerned FXS page.Unregister on reboot
option can be set to “No”, “All” or “Instance”.
1. Set to “No”: If the “Unregister on reboot” option is set to “No”, it means
that the SIP user’s information will not be cleared when the device reboots.
In other words, the SIP account will remain registered with the server even
after the device is rebooted.
2. Set to “All”: If the “Unregister on reboot” option is set to “All”, it
means that all SIP accounts associated with the device will be unregistered
when the device reboots. This option clears the SIP user’s information for all
the FXS ports on the device.
3. Set to “Instance”: If the “Unregister on reboot” option is set to
“Instance”, it means that only the SIP account associated with the concerned
FXS port will be unregistered when the device reboots. This option clears the
SIP user’s information for only the specific FXS port that is affected by the
reboot.
Default value is set to “No”
Outgoing Call Without Registration
Enables the ability to place outgoing calls even if the account is not registered (if allowed by ITSP); device will not be able to receive incoming calls. Default is No.
Register Expiration
Refreshes registration periodically with specified SIP proxy (in minutes). Maximum interval is 65535 minutes (about 45 days). Default is 60 minutes (or 1 hour).
Reregister Before Expiration
Sends re-register request after specific time (in seconds) to renew registration before the previous registration expires.
SIP Registration Failure Retry Wait Time
Sends re-register request after specific time (in seconds) when registration process fails. Maximum interval is 3600 seconds (1 hour). Default is 20 seconds.
SIP Registration Failure Retry Wait Time upon 403 Forbidden
Sends re-register request after specific time (in seconds) when registration process fails with error 403 Forbidden. Maximum interval is 3600 seconds (1 hour). Default is 1200 seconds.
Port Voltage Off upon no SIP Registration or SIP Registration Failure Delay Time of Port Voltage Off Timer Since Boot
Allows users to configure the timer of Port Voltage Off. For Port Voltage Off upon no SIP, the Valid Range is 0 to 60 with the Default value being 0 ( 0 means the port voltage is never turned off )
Enable SIP OPTIONS/NOTI FY Keep Alive
Enables SIP OPTIONS or SIP NOTIFY to track account registration status so the ATA will send periodic OPTIONS/NOTIFY message to server to track the connection status with the server. Default setting is No.
SIP OPTIONS/NOTI FY Keep Alive Interval
Configures the time interval when the ATA send OPTIONS or NOTIFY message to SIP server. The default setting is 30 seconds, which means the ATA will send an OPTIONS/NOTIFY message to the server every 30 seconds. The default range is 1-64800.
SIP OPTIONS Keep Alive Max Lost
Defines the Number of max lost packets for SIP OPTIONS Keep Alive before re- registration. Between 3-10, default is 3.
Layer 3 QoS
Defines Diff-Serv values for SIP and RTP. SIP DSCP (Diff-Serv value in decimal, 0-63, default 26) RTP DSCP (Diff-Serv value in decimal, 0-63, default 46)
Local SIP Port
Defines local port to use by the HT81x for listening and transmitting SIP packets. Default value for FXS 1 is 5060 and 5062 for FXS 2.
Local RTP Port
Defines the local RTP-RTCP port pair the HT81x will listen and transmit. It is the HT81x RTP port for channel 0. The default value for FXS port is 5004
Use Random SIP Port
Controls whether to use configured or random SIP ports. This is usually necessary when multiple HT81x are behind the same NAT. Default is No.
Use Random RTP Port
Controls whether to use configured or random RTP ports. This is usually necessary when multiple HT81x are behind the same NAT. Default is No.
Enable RTCP
Allows users to enable RTCP. The default setting is “Yes”.
Hold Target Before Refer
Allows user to hold or not hold the phone call before referring. The default setting is Yes.
Refer-To Use Target Contact
Includes target’s “Contact” header information in “Refer-To” header when using attended transfer. Default is No.
Transfer on Conference Hang-up
If set to “Yes”, when the phone hangs up as the conference initiator, the conference call will be transferred to the other parties so that other parties will remain in the conference call. Default setting is No.
Disable Bellcore Style 3-Way Conference
Gives the users the possibility of making conference calls by pressing “Flash” key, when it’s enabled by dialing *23 +second callee number. Default is No
Remove OBP from Route Header
Removes outbound proxy info in “Route” header when sending SIP packets. Default is No.
Support SIP Instance ID
Includes “SIP Instance ID” attribute to “Contact” header in REGISTER request as defined in IETF SIP outbound draft. Default is No.
Validate Incoming SIP Messages
Validates incoming SIP messages. Default is No.
Check SIP User ID for Incoming INVITE
Checks SIP User ID in the Request URI of incoming INVITE; if it doesn’t match the HT81x SIP User ID, the call will be rejected. Direct IP calling will also be disabled. Default is No.
Authenticate Incoming INVITE
Challenges the incoming INVITE for authentication with SIP 401 Unauthorized message. Default is No.
Authenticate Server Certificate Domain
Configures whether to validate the domain certificate when download the firmware/config file. If it is set to “Yes”, the phone will download the firmware/config file only from the legitimate server. The default setting is “No”.
Authenticate server certificate chain
Configures whether to validate the server certificate when download the firmware/config file. If it is set to “Yes”, the phone will download the firmware/config file only from the legitimate server. The default setting is “No”.
Allow Incoming SIP Messages from SIP Proxy Only
Checks SIP address of the Request URI in the incoming SIP message; if it doesn’t match the SIP server address of the account, the call will be rejected. Default is No.
Use Privacy Header
Determines if the “Privacy header” will be presented in the SIP INVITE message and if it includes the caller info in this header. If set to Default, it will add Privacy header unless special feature is Telkom SA or CBCOM. Default is Default.
Use P-PreferredIdentity Header
Specifies if the P-Preferred-Identity Header will be presented in the SIP INVITE message. If set to “default”, the PPreferred-Identity Header will be omitted in SIP INVITE message when Telkom SA or CBCOM is active. If set to “Yes”, the P-Preferred- Identity Header will always be presented. If set to “No”, it will be omitted. Default setting is: Default.
Use P-AccessNetwork-Info Header
With this feature enabled, device will populate the WAN access node with IEE-802.11a, IEE-802.11b in P-AccessNetwork-Info SIP header.
Use PEmergency-Info Header
This feature support of IEEE-48-addr and IEEE-EUI-64 in SIP header for emergency calls.
Use P-AssertedIdentity Header
When this feature is set to Yes, device will send P-Asserted-Identity Header on the SIP Invite. Default setting is No.
SIP REGISTER Contact Header Uses
Specifies which address (LAN or WAN address) the device will detect to use it in SIP Register Contact Header. Default is LAN Address.
Caller ID Fetch Order
Selects the Caller ID display order which need to be respected by the ATA. The available options are: Auto: When set to “Auto”, the ATA will look for the caller ID in the order of P-Asserted Identity Header, RemoteParty-ID Header and From Header in the incoming SIP INVITE. Disabled: When set to “Disabled”, all incoming calls are displayed with “Unavailable”. From Header: When set to “From Header”, the ATA will use the FROM header to display the caller ID.
Allow SIP Factory Reset
Allows to reset the devices directly through SIP Notify. If “Allow SIP Factory Reset” is set to “YES” under FXS PORT, then the ATA receives the NOTIFY from the SIP server with Event: reset, the HT should perform a factory reset after the authentication. The authentication in this case can be either with: The admin password if no SIP account is configured on the HT. With the credentials of the SIP account if configured on the ATA.
Maximum Number of SIP Request Retries
This feature allows user to configure the number of SIP retries before failover occurs. (between 1 and 10, default is 2).
SIP T1 Timeout
Defines T1 timeout value. It is an estimate of the round-trip time between the client and server transactions. For example, the HT81x will attempt to send a request to a SIP server. The time it takes between sending out the request to the point of getting a response is the SIP T1 timer. If no response is received the timeout is increased to (2T1) and then (4T1). Request re- transmit retries would continue until a maximum amount of time defined by T2. Default is 0.5 seconds.
SIP T2 Interval
Identifies maximum retransmission interval for non-INVITE requests and INVITE responses. Retransmitting and doubling of T1 continues until it reaches T2 value. Default is 4 seconds.
SIP Timer D
Configures SIP Timer D defined in RFC3261. 0 64 seconds. Default is 0.
DTMF Payload Type
Defines payload type for DTMF using RFC2833.
Preferred DTMF method (in order)
Sorts DTMF methods (in-audio, via RTP (RFC2833) or via SIP INFO) by priority.
Inband DTMF Duration
allows users to config the Inband DTMF Duration and inter-duration. The default Duration is 100 ms. Valid range: 40-2000 ms. The default Inter- duration is 50 ms. Valid range: 40-2000 ms.
Inband DTMF Tx Gain
Allows users to configure the Inband DTMF Tx Gain. The Valid rand is -12 to 12 db. The Default value is 0db.
DSP DTMF Detector Duration Threshold
Allows users to config the DSP DTMF Detector Duration Threshold The default Duration is 30 ms. Valid range: 20-2000 ms. The default Inter-duration is 30 ms. Valid range: 20-2000 ms.
Disable DTMF Negotiation
Uses above DTMF order without negotiation. Default is No.
Generate Continuous RFC2833 Events
When enabled the RFC2833 events are generated until key is released. Default is No.
Send Hook Flash Event
Default is No. If set to yes, flash will be sent as DTMF event.
Flash Digit Control
When it set to YES it allows the user to perform some call setting when both channels are used while pressing: “Flash + 1” in order to hang up the current call and resume a call that was held. “Flash + 2” in order to hold the current call and resume a call that was held. “Flash + 3” in order to perform 3-way conference. “Flash + 4” in order to perform attended transfer. Note: Please refer to the user guide for detailed steps to perform above operations.More additional Digit events were added on the new firmware 1.0.43.10.
Enable Call Waiting alertinfo In 180 Ringing Response
When set to Yes, Alert-Info header will be added in 180 Ringing for Call Waiting case
Callee Flash to 3WC
When this feature is set to Yes, device would be able to set up the 3-way conference call even when device is the callee in the second call. Default is No.
Off Hook Auto Dial Delay
Specifies the auto-dial delay after off hook.
Proxy-Require
Determines a SIP Extension to notify the SIP server that the HT81x is behind a NAT/Firewall.
Use NAT IP
Defines NAT IP address used in SIP/SDP messages. It should only be used if required by ITSP.
SIP User-Agent
This feature allows users to configure SIP User Agent. If not configured, device will use the default User Agent header.
SIP User-Agent Postfix
Configures the SIP User-Agent Postfix
Add MAC in User-Agent
This feature allows users to configure “User-Agent” in the SIP header field, when this feature is set to”No”, “UserAgent” does not carry a MAC, when this feature is set “Yes except REGISTER”, “User-Agent” in REGISTERSIP header field does not carry MAC but other SIP packet header fields carries MAC, when this feature is set to “Yes to all SIP”, “User-Agent” in the SIP packet header field will carries the MAC.
Use MAC Header
This feature allows users to configure MAC Header in the SIP packet header field, when this feature is set to “No” ,the MAC header field is not carried in the SIP packet header field, when this feature is set to “REGISTER Only”, the register packet header field carries the MAC header field but the remaining SIP packets do not carry MAC header fields, when this feature is set to “Yes to all SIP”, the MAC header field is carried in the SIP data packet header field.
RFC2543 Hold
Toggles between RFC2543 hold and RFC3261 hold. RFC2543 hold allows to disable the hold music sent to the other side, in this case IP address (0.0.0.0) it will be sent in SDP instead of the IP address of the unit . RFC3261 (a line) will play the hold music to the other side.
Disable Call Waiting
Disables receiving a second incoming call when the line is engaged. Default is No.
Disable Call Waiting Caller ID
Disables displaying caller ID when receiving a second incoming call. Default is No.
Disable Call Waiting Tone
Disables playing call waiting tone during active call when receiving a second incoming call. The CWCID will still be displayed. Default is No.
Disable Connected Line ID
Disables displaying the number of the person answering the phone. Default is No.
Disable Receiver Off Hook Tone
Enables / disables the warning to alert that the phone has been left off-hook for an extended period of time. Default is No.
Disable Reminder Ring for On-Hold Call
Enables playing the reminder ring. Default is No.
Disable Reminder Ring for DND
This feature allows user to disable reminder ring when FXS port is on DND mode. Default is Yes.
Disable Visual MWI
Disables use of visual message waiting indicator when there is an unread voicemail message. Default is No.
Visual MWI Type
Configures Visual WMI Type of signal sent to the analog phone to make it turn the lamp ON upon receiving a Voice mail. Check the phone’s manual to find out what signal is supported, FSK (default) or Neon. Note: Some phones (depending on the model of the analog phone) when this feature is set to NEON it might auto ring (short beeps) when there is a voice mail available for that FXS port where it is connected.
MWI Tone
When set to Default, device will play Stutter Dial Tone when there is voicemail, if set to Special Proceed Indication Tone, device will play the configured special proceed indication tone upon user offhook when there is voicemail
Do Not Escape `#’ as %23 in SIP URI
Replaces # by %23 in some special situations. Default is No.
Disable Multiple m Line in SDP
Sends only one m line in SDP, regardless of how many m fields are in the incoming SDP. Default is No.
Ring Timeout
Stops ringing when incoming call if not answered within a specific period of time. When set to 0 there will be no ringing timeout. Default is 60 seconds.
Hunting Group Ring Timeout
If call is not answered within this designated time period, the call will be forwarded to the next member of a Hunt Group. Default value is 20 seconds.
Hunting Group Type
Specifies Hunting Group Type, either “Linear” or “Circular”. Linear style will sort the call to the lowest numbered available line, this is also called “serial hunting”. Circular style will distribute the calls “round-robin”. If a call is assigned to line 1, the next call goes to 2 and the next to 3. The succession throughout each of the lines continues even if one of the previous lines becomes available. When the end of the hunt group is reached, the hunting starts over at the first line. Lines are skipped if they are still busy on a previous call. Default is Circular.
Delayed Call Forward Wait Time
Forwards incoming call if not answered within a specific period of time when delayed call forward is activated locally (using *92 code). Default value is 20 seconds.
No Key Entry Timeout
Initiates the call within this time interval if no additional key entry during dialing stage. Default is 4 seconds.
Early Dial
Sends an early INVITE each time a key is pressed when a user dials a number. Otherwise, only one INVITE is sent after full number is dialed (user presses Dial Key or after “no key entry timeout” expires). This option should be used only if there is a SIP proxy is configured and supporting “484 Incomplete Address” responses. Otherwise, the call will likely be rejected by the proxy (with a 404 Not Found error). Default is No. This feature is NOT designed to work with and should NOT be enabled for direct IP-to-IP calling.
Dial Plan Prefix
Adds specified prefix to dialed number.
Use # as Dial Key
Treats “#” as the “Send” (or “Dial”) key. If set to “No”, this “#” key can be included as part of the dialed number. Default is Yes.
Disable # as Redial Key
Disables # to act as Redial key. If set to “Yes” and feature “Use # as Dial Key” set to Yes, the # key will act as dial key but not as redial key. Default is No.
Dial Plan
Dial Plan Rules: 1. Accept Digits: 1,2,3,4,5,6,7,8,9,0 , *, #, A,a,B,b,C,c,D,d 2. Grammar: x any digit from 0-9; a. xx+ at least 2 digits number; b. xx exactly 2 digits number; c. ^ exclude; d. . wildcard, matches one or more characters
e. [3-5] any digit of 3, 4, or 5; f. [147] any digit 1, 4, or 7; g. <2=011> replace digit 2 with 011 when dialing h. <=1> add a leading 1 to all numbers dialed, vice versa will remove a 1 from the number dialed i. | or j. Flag T when adding a “T” at the end of the dial plan, the phone will wait for 3 seconds before dialing out. This gives users more flexibility on their dial plan setup. E.g. with dial plan 1XXT, phone will wait for 3 seconds to let user dial more than just 3 digits if needed. Originally the phone will dial out immediately after dialing the third digit. Example 1: {[369]11 | 1617xxxxxxx} Allow 311, 611, 911, and any 10-digit numbers of leading digits 1617 Example 2: {^1900x+ | <=1617>xxxxxxx} Block any number with leading digits 1900 and add prefix 1617 for any dialed 7-digit numbers Example 3: {1xxx[2-9]xxxxxx | <2=011>x+} Allow any length of number with leading digit 2 and 10 digit-numbers of leading digit 1 and leading exchange number between 2 and 9; If leading digit is 2, replace leading digit 2 with 011 before dialing. 1. Default: Outgoing { x+ | +x+ | x+ | xxx+ } Example of a simple dial plan used in a Home/Office in the US: { ^1900x. | <=1617>[2-9]xxxxxx | 1[2-9]xx[2-9]xxxxxx | 011[2-9]x. | [3469]11 } Explanation of example rule (reading from left to right): ^1900x. prevents dialing any number started with 1900 <=1617>[2-9]xxxxxx allows dialing to local area code (617) numbers by dialing 7 numbers and 1617 area code will be added automatically 1[2-9]xx[2-9]xxxxxx allows dialing to any US/Canada Number with 11 digits length 011[2-9]x. allows international calls starting with 011 [3469]11 allow dialing special and emergency numbers 311, 411, 611 and 911 Note: In some cases, user wishes to dial strings such as 123 to activate voice mail or other application provided by service provider. In this case should be predefined inside dial plan feature. An example dial plan will be: { x+ } which allows the user to dial * followed by any length of numbers.
SUBSCRIBE for MWI
Sends SUBSCRIBE periodically (depends on “Register Expiration” parameter) for message waiting indication. Default is No.
Subscribe Retry Wait Time upon 403 Forbidden
This feature allows users to adjust the subscribe retry waiting time while it is rejected with 403 forbidden. Default is 0. Valid range: 0-10080 in minutes. Note: Not supported on HT818
Send Anonymous
Sets “From”, “Privacy” and “P_Asserted_Identity” headers in outgoing INVITE message to “anonymous”, blocking caller ID. Default is No.
Anonymous Call Rejection
Rejects incoming calls with anonymous caller ID with “486 Busy here” message. Default is No.
Special Feature
Selects Soft switch vendors’ special requirements Examples of vendors: BroadSoft, CBCOM, RNK, Huawei, China Mobile, ZTE IMS, PhonePower, TELKOM SA, Vonage, Metaswitch, CenturyLink, MTS, Oi_BR, Telefonica, GIBTELECOM. The default is Standard.
Enable Session Timer
Disable the session timer when this option is set to “No”. By default, this option is enabled.
Session Expiration
Enables SIP sessions to be periodically “refreshed” via a SIP request (UPDATE, or re-INVITE). When the session interval expires, if there is no refresh via an UPDATE or re-INVITE message, the session will be terminated. Session Expiration is the time (in seconds) at which the session is considered timed out, if no successful session refresh transaction occurs beforehand. Valid range is 90-64800 seconds. Default is 180 seconds.
Min-SE
Defines Minimum session expiration (in seconds). Default is 90 seconds.
Caller Request Timer
Uses session timer when making outbound calls if remote party supports it. Valid range is 90-64800 seconds. Default is No.
Callee Request Timer
Uses session timer when receiving inbound calls with session timer request. Default is No.
Force Timer
Uses session timer even if the remote party does not support this feature. Selecting “No” will enable session timer only when the remote party supports it. To turn off Session Timer, select “No” for Caller and Callee Request Timer, and Force Timer. Default is No.
UAC Specify Refresher
Specifies which end will act as refresher for outgoing calls. Default is Omit. UAC: The HandyTone acts as the refresher. UAS: Callee or proxy server act as the refresher.
UAS Specify Refresher
Specifies which end will act as refresher for incoming calls. Default is Omit.: UAS: The HandyTone acts as the refresher. UAC: Callee or proxy server act as the refresher.
Force INVITE
Uses INVITE message to refresh the session timer. Default is No.
When To Restart Session After ReINVITE received
Allows users to delay posting Media Change Event, it can be set to “Immediately” or to “After replying 200OK” The default value is “Immediately”.
Enable 100rel
Appends “100rel” attribute to the value of the required header of the initial signaling messages. Default is No.
Add Auth Header on Initial REGISTER
Adds “Authentication” header with blank “nonce” attribute in the initial SIP REGISTER request. Default is No.
Conference URI
Allows users to manually configure the conference URL. The default is null.
Use First Matching Vocoder in 200OK SDP
Includes only the first matching vocoder in its 200OK response, otherwise it will include all matching vocoders in same order received in INVITE. Default is No.
Preferred Vocoder
Configures vocoders in a preference list (up to 8 preferred vocoders) that will be included with same order in SDP message. Vocoder types are G.711 A-/U-law, G.726-32, G.723, G.729, iLBC and OPUS
Voice Frames per TX
Transmits a specific number of voice frames per packet. Default is 2; increases to 10/20/32/64 for G711/G726/G723/other codecs respectively.
G723 Rate
Operates at specified encoding rate for G.723 vocoder. Available encoding rates are 6.3kbps or 5.3kbps. Default is 6.3kbps.
iLBC Frame Size
Specifies iLBC packet frame size (20ms or 30ms). Default is 20ms.
Disable OPUS Stereo in SDP
Disables OPUS stereo in SDP. Default is No.
iLBC Payload Type
Determines payload type for iLBC. Valid range is between 96 and 127. Default is 97.
OPUS Payload Type
Determines payload type for OPUS. Valid range is between 96 and 127. Default is 123.
VAD
Allows detecting the absence of audio and conserves bandwidth by preventing the transmission of “silent packets” over the network. Default is No.
Symmetric RTP
Changes the destination to send RTP packets to the source IP address and port of the inbound RTP packet last received by the device. Default is No.
Fax Mode
Specifies the fax mode: T.38 (Auto Detect) FoIP by default, or Pass-Through. If using Pass-through mode, select preference codec as PCMU or PCMA.
Re-Invite after Fax Tone Detected
Permits the unit to send out the re-INVITE for T.38 or Fax Pass Through if a fax tone is detected. Default is Enabled
Jitter Buffer Type
Selects jitter buffer type (Fixed or Adaptive) based on network conditions.
Jitter Buffer Length
High (initial 200ms, min 40ms, max 600ms) Note: not all vocoders can meet the high requirement. Medium (initial 100ms, min 20ms, max 200ms). Low (initial 50ms, min 10ms, max 100ms).
SRTP Mode
Selects SRTP mode to use (“Disabled”, “Enabled but not forced”, or “Enabled and forced”). Default is Disabled It uses SDP Security Description to exchange key. Please refer to SDES: https://tools.ietf.org/html/rfc4568 SRTP: https://www.ietf.org/rfc/rfc3711.txt
SRTP Key Length
Allows users to select supported SRTP Key Length. the available values are :
1. AES 128&256 bit 2. AES 128 bit 3. AES 256 bit Set to AES 128&256 bit By
Default.
Crypto Life Time
Adds crypto life time header to SRTP packets. Default is Yes.
SLIC Setting
Depends on standard phone type (and location).
Caller ID Scheme
Selects the caller id scheme, for example: Bellcore/Telcordia, ETSI-FSK …
DTMF Caller ID Defines the start and stop tones (Default, A, B, C, D or #) to delimit CID.
Disable Unknown Caller ID
Disable analog phone’s caller ID when receiving a call with “Anonymous”, “unavailable” or “unknown” in FROM header and without “Display info”. Note: This relies also on analog phone’s design, some phones will still display “unknown” with this feature enabled. Default is No.
Replace Beginning `+’ with 00 in Caller ID
When this feature is set to Yes, device will replace the “+” sign at the beginning of a number in the FROM header. Default is No.
Polarity Reversal
Reverses the polarity upon call establishment and termination. Default is No.
Loop Current Disconnect
Allows the traditional PBX used with HT81x to apply this method for signaling call termination. Method initiates short voltage drop on the line when remote (VoIP) side disconnects an active call. Default is No.
Play busy/reorder tone before Loop Current Disconnect
Allow user to configure if it will play busy/reorder tone before loop current disconnect upon call fail. Default is No.
Loop Current Disconnect Duration
Configures the duration of voltage drop described in topic above. HT81x support a duration range from 100 to 10000ms. Default value is 200.
Enable Pulse Dialing
Allow users to enable Pulse Dialing option under FXS Port. Default is No.
Pulse Dialing Standard
Allows users to use Swedish pulse dialing standard or New Zealand pulse dialing standard. Default is General Standard.
Enable Hook Flash
Enables the FLASH button to be used for terminating calls. Default is Yes.
Hook Flash Timing
Defines the time period when the cradle is pressed (Hook Flash) to simulate FLASH. To prevent unwanted activation of the Flash/Hold and automatic phone ring-back, adjust this time value. HT81x support a range from 40 to 2000 ms. Default values are 300 minimum and 1100 maximum.
On Hook Timing
Specifies the on-hook time for an on-hook event to be validated. HT81x support a range from 40 to 2000 ms. Default value is 400.
Gain
Adjusts the voice path volume. · Rx is a gain level for signals transmitted by FXS · Tx is a gain level for signals received by FXS. Default = 0dB for both parameters. Loudest volume: +6dB Lowest volume: -6dB. User can adjust volume of call using the Rx gain level parameter and the Tx gain level parameter located on the FXS port configuration page. If call volume is too low when using the FXS port (ie. the ATA is at user site), adjust volume using the Rx gain level parameter under the FXS port configuration page. If voice volume is too low at the other end, user may increase the far end volume using the Tx gain level parameter under the FXS port configuration PAGE.
Disable Line Echo Canceller
Disables the LEC per call base. Recommended for Fax/Data calls. Default is No.
Disable Network Echo Suppressor
Disables the NEC per call base. Recommended for Fax/Data calls. Default is No.
Outgoing Call Duration Limit
Defines the call duration limit for the outgoing calls. Default is 0 (No limit).
Incoming Call Duration Limit
allows users to configure the Incoming Call Duration Limit. Valid Range is 0 – 180 ( 0 is no limit ) Default value is 0.
Ring Frequency
Customizes ring frequency. Valid options: 20Hz 25Hz. Default is 20Hz.
Enable High Ring Power
Configures a high ringing voltage output for the ATA.
OnHOOK DC Feed Current
This feature is used to adjust DC feed current.
RFC2833 Events Count
This feature allows users to customize the count of RFC2833 events. The Valid Value Range is between 2 and 10 , if it is set to 0 , it means continuous RFC2833 events are activated Default is 8.
RFC2833 End Events Count
This feature allows users to customize the count of RFC2833 end events. Default is 3.
Distinctive Ring Tone
Customizes the Ring Tone 1 to 3 with associate caller ID: when selected, if
caller ID is configured, then the device will ONLY use this ring tone when the
incoming call is from the Caller ID. System Ring Tone is used for all other
calls. When selected but no Caller ID is configured, the selected ring tone
will be used for all incoming calls using the FXS port. Distinctive ring tones
can be configured not only for matching a whole number, but also for matching
prefixes. In this case the symbol “x+” will be used. For example: if
configured as 617x+, Ring Tone 1 will be used in case of call arrived from the
area code 617. Any other incoming call will ring using cadence defined in
parameter System Ring Cadence located under Advanced Settings Configuration
page.
Note: If server supports Alert-Info header and standard ring tone set
(Bellcore) or distinctive ring tone 1-10 is specified, then the ring tone in
the Alert-Info header from server will be used. Bellcore rings and tones are
independent from custom ring tones. The custom ring tones can also be
specified by alert-info header, for example Alert-Info: <127.0.0.1>;
info=ring5
Ring tones
Configures the ring tone cadence preferences. User has 10 choices. The configuration, completed in Distinctive Ring Tones block in the same page, applies to ring tones cadences configured here.
Distinctive Call Waiting Tone
Customizes the Call Waiting Tone 1 to 10 with associate caller ID: when selected, if caller ID is configured, then the device will ONLY use this call waiting tone when the incoming call waiting is from the Caller ID. When selected but no Caller ID is configured, the selected call waiting tone will be used for all incoming waiting calls using the FXS port. Distinctive Call Waiting Tones can be configured not only for matching a whole number, but also for matching prefixes. In this case symbol “x+” will be used.
For example: If configured as 617x+, Call Waiting Tone 1 will be used in case of waiting call arrived from the area code 617. Any other incoming call waiting will be using cadence defined in parameter Call Waiting Tone located under Advanced Settings Configuration page.
Call Waiting Tones
This feature allows user to customize call waiting tone. User has 10 choices. Syntax: f1=val[,f2=val[,c=on1/off1[-on2/off2[-on3/off3]]]]; (Frequencies are in (300, 3400) Hz and cadence on and off are in (0, 64000) ms) Note: The configuration, completed in Distinctive Call Waiting Tones block in the same page, applies to call waiting cadences configured here. Default is f1=440@-13,c=300/10000;
Call Features Settings
Enable Call Features
When enabled, Do No Disturb, Call Forward and other call features can be used via the local feature codes on the phone. Otherwise, the ITSP feature codes will be used. Enable All will override all individual features enable setting. Default is Yes
Reset Call Features
Allows users to reset all call features configuration. Default is No
SRTP Feature
Allow users to customize the SRTP feature codes. Default is Yes Enable SRTP: Default is 16 Disable SRTP: Default is 17
SRTP per call Feature
Enable SRTP per call: Default is 18 Disable SRTP per call: Default is 19
CID Feature
Allow users to customize the CID feature codes. Default is Yes Enable CID: Default is 31 Disable CID: Default is 30
CID per call Feature
Enable CID per call: Default is 82 Disable CID per call: Default is 67
Direct IP Calling Feature
Allow users to customize the Direct IP feature code. Default is Yes Direct IP Calling: Default is 47
CW Feature
Allow users to customize the CW feature codes. Default is Yes Enable CW: Default is 51 Disable CW: Default is 50
CW per call Feature
Enable CW per call: Default is 71 Disable CW per call: Default is 70
Call Return Feature
Allow users to customize the Call Return feature code. Default is Yes Call return: Default is 69
Unconditional Forward Feature
Allow users to customize the Unconditional Forward feature codes. Default is Yes Enable Unconditional Forward: Default is 72 Disable Unconditional Forward: Default is 73
Busy Forward Feature
Allow users to customize the Busy Forward feature codes. Default is Yes Enable Busy Forward: Default is 90 Disable Busy Forward: Default is 91
Delayed Forward Feature
Allow users to customize the Delayed Forward feature codes. Default is Yes Enable Delayed Forward: Default is 92 Disable Delayed Forward: Default is 93
Paging Feature
Allow users to customize the Paging feature code. Default is Yes Paging: Default is 74
DND Feature
Allow users to customize the CW feature codes. Default is Yes Enable DND: Default is 78 Disable DND: Default is 79
Blind Transfer Feature
Allow users to customize the Blind Transfer feature code. Default is Yes Enable Blind Transfer: Default is 87
Disable LEC per call Feature
Default is Yes Disable LEC per call: Default is 03
Disable Bellcore Style 3-Way Conference
Default is No
Star Code 3WC Feature
Default is Yes Star Code 3WC: Default is 23
Forced Codec Feature
Allow users to customize the Forced Codec feature code. Default is Yes Forced Codec: Default is 02
PCMU Codec Feature
Default is Yes PCMU Codec: Default is 7110
PCMA Codec Feature
G723 Codec Feature
G729 Codec Feature
iLBC Codec Feature
Default is Yes PCMA Codec: Default is 7111
Default is Yes G723 Codec: Default is 723
Default is Yes G729 Codec: Default is 729
Default is Yes iLBC Codec: Default is 7201
FXS Ports Page Definitions
FXS Ports
Port
Display the port number
SIP User ID
Defines user account information provided by VoIP service provider (ITSP). Usually in the form of digit similar to phone number or actually a phone number.
Authentica Determines account authenticate ID provided by VoIP service provider (ITSP). Can be identical to or different
te ID
from “SIP user ID”.
Password Specifies account password provided by VoIP service provider (ITSP) to register to SIP servers.
Name
Chooses a name to be associated to user.
Profile ID Defines the profile ID for each port.
Hunting Group
Configures hunting group feature on the specific port.
For example: Port 1, 2, and 3 are members of the same Hunting Group. Port 1 is
registered with a SIP account.
Ports 2, and 3 are not registered. Ports 2 and 3 will be able to place
outbound calls using the SIP account of port 1. Select appropriate value for
Hunting Group feature.
The original SIP account should be set to Active while the group members
should be set to the port number of the Active Port.
Example configuration of a Hunting group:
FXS Port #1: SIP UserID and Authenticate ID entered, Hunting group set to
“Active”
FXS Port #2: SIP UserID and Authenticate ID left blank, Hunting Group set to
“1”
FXS Port #3: SIP UserID and Authenticate ID left blank, Hunting Group set to
“1”
FXS Port #4: SIP UserID and Authenticate ID entered, Hunting group set to
“None”
Hunting Group 1 contains ports 1, 2, 3. FXS port 4 is registered but it is not
added to the Hunting Group 1.
Note: HT812/HT814 will use CID name from FXS port initiating the outgoing call
if the “Name” field is entered for that specific port.
Request URI Routing ID
If configured, device will route the incoming call to designated port by request URI user ID in SIP INVITE.
Enable Port
Enables / Disables the port.
Off hook Auto-Dial
Configures a User ID or extension number that is automatically dialed when off-hook. Only the user part of a SIP address needs is entered here. The HT812/HT814 will automatically append the “@” and the host portion of the corresponding SIP address.
Important Settings
Table 10: FXS Ports
NAT Settings
If you plan to keep the Handy Tone within a private network behind a firewall,
we recommend using STUN Server.
The following three settings are useful in the STUN Server scenario:
1. STUN Server (under advanced settings webpage) enter a STUN server IP (or
FQDN) that you may have or look up a free public STUN server on the internet
and enter it on this field. If using public IP, keep this field blank.
2. Use random SIP/RTP ports (under advanced settings webpage), this setting
depends on your network settings. Generally, if you have multiple IP devices
under the same network, it should be set to Yes. If using a public IP address,
set this parameter to No.
3. NAT traversal (under the FXS web page) Set this to Yes when gateway is
behind firewall on a private network.
DTMF Methods
The HT812/HT814 support the following DTMF mode:
· DTMF in-audio
· DTMF via RTP (RFC2833)
· DTMF via SIP INFO
Set priority of DTMF methods according to your preference. This setting should
be based on your server DTMF setting.
Preferred Vocoder (Codec)
The HT812/HT814 support following voice codecs. On Profile pages, choose the
order of your codecs:
· PCMU/A (or G711µ/a)
· G729 A/B
· G723.1
· G726
· iLBC
· OPUS
· G722
Configuring HT812/HT814 Through Voice Prompts
As mentioned previously, The HT812/HT814 have a built-in voice prompt menu for
simple device configuration. Please refer to “Understanding HT812/HT814
Interactive Voice Prompt Response Menu” for more information about IVR and how
to access its menu.
DHCP MODE
Select voice menu option 01 to enable HT812/HT814 to use DHCP.
STATIC IP MODE
Select voice menu option 01 to enable HT812/HT814 to use STATIC IP mode, then
use option 02, 03, 04, 05 to set up IP address, Subnet Mask, Gateway and DNS
server respectively.
PPPOE MODE
Select voice menu option 01 to allow the HT812/HT814 to enable the PPPoE mode.
PPPoE Username and Password should be configured from web GUI.
FIRMWARE SERVER IP ADDRESS
Select voice menu option 13 to configure the IP address of the firmware
server.
CONFIGURATION SERVER IP ADDRESS
Select voice menu option 14 to configure the IP address of the configuration
server.
UPGRADE PROTOCOL
Select the menu option 15 to choose firmware and configuration upgrade
protocol between TFTP, FTP, FTPS, HTTP and HTTPS. Default is HTTPS.
FIRMWARE UPGRADE MODE
Select voice menu option 17 to choose firmware upgrade mode among the
following three options: 1) Always check, 2) check when pre/suffix changes,
and 3) never upgrade.
WAN PORT WEB ACCESS
Select voice menu option 12 to enable/disable web access from WAN port. Press
9 in this menu to toggle between enable / disable. Default is disabled.
Configuration through a Central Server
The HT812/HT814 can be automatically configured from a central provisioning
system.
When HT812/HT814 boots up, it will send TFTP, FTP/FTPS or HTTP/HTTPS requests
to download configuration files, “cfg000b82xxxxxx” and “cfg00082xxxxxx.xml”,
where “000b82xxxxxx” is the LAN MAC address of the HT812/HT814. If the
download of “cfgxxxxxxxxxxxx.xml” is not successful, the provision program
will issue request a generic configuration file “cfg.xml”. Configuration file
name should be in lower case letters. The configuration data can be downloaded
via TFTP, FTP/FTPS or HTTP/HTTPS from the central server. A service provider
or an enterprise with large deployment of HT812/HT814 can easily manage the
configuration and service provisioning of individual devices remotely from a
central server.
Grandstream provides a central provisioning system GAPS (Grandstream Automated
Provisioning System) to support automated configuration of Grandstream
devices. GAPS uses HTTPS and other communication protocols to communicate with
each individual Grandstream device for firmware upgrade, remote reboot, etc.
Grandstream provides GAPS service to VoIP service providers. Use GAPS for
either simple redirection or with certain special provisioning settings. At
boot-up, Grandstream devices by default point to Grandstream provisioning
server GAPS, based on the unique MAC address of each device, GAPS provision
the devices with redirection settings so that they will be redirected to
customer’s TFTP or HTTP/HTTPS/FTP/FTPS server for further provisioning.
Grandstream also provides configuration tools (Windows and Linux/Unix version)
to facilitate the task of generating device configuration files.
The Grandstream configuration tools are free to end users. The configuration
tools and configuration templates are available for download from
http://www.grandstream.com/support/tools
Register a SIP Account
The HT812/HT814 support 2 profiles which can be configured with 2 SIP
accounts. Please refer to the following steps in order to register your
accounts via web user interface
1. Access your HT812/HT814 web UI by entering its IP address in your favorite
browser. 2. Enter your admin password (default: admin). 3. Press Login to
access your settings. 4. Go to Profile (1 or 2) pages. 5. In Profile tab, set
the following:
1. Account Active to Yes. 2. Primary SIP Server field with your SIP server IP
address or FQDN. 3. Failover SIP Server with your Failover SIP Server IP
address or FQDN. Leave empty if not available. 4. Prefer Primary SIP Server to
No or Yes depending on your configuration. Set to No if no Failover SIP Server
is
defined. If “Yes”, account will register to Primary SIP Server when failover
registration expires. 5. Outbound Proxy: Set your Outbound Proxy IP Address or
FQDN. Leave empty if not available. 6. After configuring the SIP server and
activating the profiles, you should access to FXS Ports page to register your
accounts. In FXS Ports tab, set the following: 1. SIP User ID: User account
information, provided by VoIP service provider (ITSP). Usually in the form of
digit similar to
phone number or actually a phone number. 2. Authenticate ID: SIP service
subscriber’s Authenticate ID used for authentication. Can be identical to or
different
from SIP User ID. 3. Authenticate Password: SIP service subscriber’s account
password to register to SIP server of ITSP. For security
reasons, the password will field will be shown as empty. 4. Name: Any name to
identify this specific user. 5. Set Enable Port to Yes. For more information,
related to above options please refer to Profile(s) settings and FXS Port
Settings. 7. Press Apply at the bottom of the page to save your configuration.
Figure 11: SIP Profiles Settings
Figure 12: SIP Accounts settings After applying your configuration, your
account will register to your SIP Server, you can verify if it has been
correctly registered with your SIP server from your HT812/HT814 web interface
under Status Port Status Registration (If it displays Registered, it means
that your account is fully registered, otherwise it will display Not
Registered so in this case you must double check the settings or contact your
provider).
Figure 13: Accounts Status When all the FXS ports are registered, the simultaneous rings will have one second delay between each ring on each phone.
Call Features
The HT812/HT814 support all the traditional and advanced telephony features.
Key Call Features
*02
Forcing a Codec (per call) 027110 (PCMU), 027111 (PCMA), 02723 (G723), 02729 (G729), 027201 (iLBC), 02722 (G722).
Disable LEC (per call) Dial “03″ +” number”. 03
No dial tone is played in the middle.
*16 Enable SRTP
*17 Disable SRTP
*30 Block Caller ID (for all subsequent calls)
*31 Send Caller ID (for all subsequent calls)
47 Direct IP Calling. Dial “47” + “IP address”. No dial tone is played in the middle.
*50 Disable Call Waiting (for all subsequent calls)
*51 Enable Call Waiting (for all subsequent calls)
67 Block Caller ID (per call). Dial “67″ +” number”. No dial tone is played in the middle.
82 Send Caller ID (per call). Dial “82″ +” number”. No dial tone is played in the middle.
69 Call Return Service: Dial 69 and the phone will dial the last incoming phone number received.
70 Disable Call Waiting (per call). Dial “70″ +” number”. No dial tone is played in the middle.
71 Enable Call Waiting (per call). Dial “71″ +” number”. No dial tone is played in the middle
*72
Unconditional Call Forward: Dial “*72” and then the forwarding number followed by “#”. Wait for dial tone and hang up. (dial tone indicates successful forward)
*73
Cancel Unconditional Call Forward. To cancel “Unconditional Call Forward”, dial “*73”, wait for dial tone, then hang up.
74 Enable Paging Call: Dial “74” and then the destination phone number you want to page.
*78 Enable Do Not Disturb (DND): When enabled all incoming calls are rejected.
*79 Disable Do Not Disturb (DND): When disabled, incoming calls are accepted.
Key Call Features *87 Blind Transfer
90 Busy Call Forward: Dial “90” and then the forwarding number followed by “#”. Wait for dial tone then hang up.
91 Cancel Busy Call Forward. To cancel “Busy Call Forward”, dial “91”, wait for dial tone, then hang up.
*92
Delayed Call Forward. Dial “*92” and then the forwarding number followed by “#”. Wait for dial tone then hang up.
93 Cancel Delayed Call Forward. To cancel Delayed Call Forward, dial “93”, wait for dial tone, then hang up
Flash / Hoo k
Toggles between active call and incoming call (call waiting tone). If not in conversation, flash/hook will switch to a new channel for a new call.
Pressing pound sign will serve as Re-Dial key.
Table 11: HT812/HT814 Call Features
Rebooting HT812/HT814 from Remote
Press “Reboot” button at the bottom of the configuration menu to reboot the
ATA remotely. The web browser will then display a message window to confirm
that reboot is underway. Wait 30 seconds to log in again.
UPGRADING AND PROVISIONING
The HT812/HT814 can be upgraded via TFTP/FTP/FTPS/HTTP/HTTPS by configuring
the URL/IP Address for the TFTPFTP/FTPS/HTTP/HTTPS server and selecting a
download method. Configure a valid URL for TFTP or FTP/FTPS or HTTP/HTTPS
(default is HTTPS); the server name can be FQDN or IP address.
Examples of valid URLs:
firmware.grandstream.com
fw.ipvideotalk.com/gs
Firmware Upgrade procedure
Please follow below steps in order to upgrade the firmware version of your
HT812/HT814:
1. Access your HT812/HT814 UI by entering its IP address in your favorite
browser. 2. Enter your admin password (default: admin). 3. Press Login to
access your settings. 4. Go to Advanced Settings Firmware Upgrade and
Provisioning page, and enter the IP address or the FQDN for the
upgrade server in “Firmware Server Path” field and choose to upgrade via TFTP
or HTTP/HTTPS or FTP/FTPS. 5. Make sure to check “Always Check for New
Firmware”. 6. Update the change by clicking the ” Apply” button at the bottom
of the page. Then “Reboot” or power cycle the
HT812/HT814 to update the new firmware.
Figure 14: Firmware Upgrade Page
Upgrading via Local Directory
1. Download the firmware file from Grandstream web site 2. Unzip it and copy
the file in to a folder in your PC 3. From the HT812/HT814 web interface
(Advanced Settings page) you can browse your hard drive and select the folder
you
previously saved the file (HT8xfw.bin)
4. Click “Upload Firmware” and wait few minutes until the new program is
loaded.
Always check the status page to see that the program version has changed.
the filename in URL for the firmware upgrade has been disabled on the latest
firmware upgrade 1.0.43.11
Upgrading via Local TFTP/HTTP/HTTPS/FTP/FTPS Servers
For users that would like to use remote upgrading without a local
TFTP/FTP/FTPS/HTTP/HTTPS server, Grandstream offers a NAT-friendly HTTP
server. This enables users to download the latest software upgrades for their
devices via this server. Please refer to the webpage:
https://www.grandstream.com/support/firmware
Alternatively, users can download for example a free TFTP or HTTP server and
conduct a local firmware upgrade. A free window version TFTP server is
available for download from:
http://www.solarwinds.com/products/freetools/free_tftp_server.aspx
http://tftpd32.jounin.net/.
Instructions for local firmware upgrade via TFTP:
1. Unzip the firmware files and put all of them in the root directory of the
TFTP server. 2. Connect the PC running the TFTP server and the phone to the
same LAN segment. 3. Launch the TFTP server and go to the File
menu->Configure->Security to change the TFTP server’s default setting from
“Receive Only” to “Transmit Only” for the firmware upgrade. 4. Start the TFTP
server and configure the TFTP server in the phone’s web configuration
interface. 5. Configure the Firmware Server Path to the IP address of the PC.
6. Save and Apply the changes and reboot the HT812/HT814.
End users can also choose to download a free HTTP server from
http://httpd.apache.org/ or use Microsoft IIS web server.
Firmware and Configuration File Prefix and Postfix
Firmware Prefix and Postfix allows device to download the firmware name with
the matching Prefix and Postfix. This makes it the possible to store all of
the firmware with different version in one single directory. Similarly, Config
File Prefix and Postfix allows device to download the configuration file with
the matching Prefix and Postfix. Thus, multiple configuration files for the
same device can be stored in one directory. In addition, when the field “Check
New Firmware only when F/W pre/suffix changes” is set to “Yes”, the device
will only issue firmware upgrade request if there are changes in the firmware
Prefix or Postfix.
Managing Firmware and Configuration File Download
When “Automatic Upgrade” is set “Yes, every” the auto check will be done in
the minute specified in this field. If set to “daily at hour (0-23)”, Service
Provider can use P193 (Auto Check Interval) to have the devices do a daily
check at the hour set in this field with either Firmware Server or Config
Server. If set to “weekly on day (0-6)” the auto check will be done on the day
specified in this field. This allows the device to periodically check if there
are any new changes need to be taken on a scheduled time. By defining
different intervals in P193 for different devices, Server Provider can spread
the Firmware or Configuration File download in minutes to reduce the Firmware
or Provisioning Server load at any given time
Configuration File Download
Grandstream SIP Devices can be configured via the Web Interface as well as via
a Configuration File (binary or XML) through TFTP, FTP/FTPS or HTTP/HTTPS. The
Config Server Path is the TFTP or HTTP/HTTPS server path for the configuration
file. It needs to be set to a valid URL, either in FQDN or IP address format.
The Config Server Path can be the same or different from the Firmware Server
Path.
A configuration parameter is associated with each particular field in the web
configuration page. A parameter consists of a Capital letter P and 2 to 3
(Could be extended to 4 in the future) digit numeric numbers. i.e., P2 is
associated with the “New Password” in the Web GUI->Maintenance->Web/SSH Access
page->Admin Password. For a detailed parameter list, please refer to the
corresponding firmware release configuration template.
When the HT812/HT814 boots up or reboots, it will send a request to download a
file named “cfgxxxxxxxxxxxx” followed by a configuration XML file named
“cfgxxxxxxxxxxxx.xml”, where “xxxxxxxxxxxx” is the MAC address of the phone,
i.e., “cfg000b820102ab” and “cfg000b820102ab.xml”. If the download of
“cfgxxxxxxxxxxxx.xml” file is not successful, the provision program will
download a generic cfg.xml file and then download cfg
HT818/HT814 supports DHCP option 67 allowing to provide custom name for the
provisioning file. If DHCP option 67 is used, the following file download
sequence will be applied:
Step 1: cfg
Step 2: <option 67 bootfile> cfg
Notes:
1. Only XML or binary config file formats are accepted. 2. The MAC header in
XML config file should be the device MAC or needs to be removed completely.
Figure 15: XML Config File MAC Header the filename in URL for config provision has been disabled on the latest firmware upgrade 1.0.43.11
RESTORE FACTORY DEFAULT SETTINGS
Warning Restoring the Factory Default Settings will delete all configuration
information on the phone. Please backup or print all the settings before you
restore to the factory default settings. Grandstream is not responsible for
restoring lost parameters and cannot connect your device to your VoIP service
provider.
There are three (3) methods for resetting your unit:
Using the Reset Button
To reset default factory settings using the reset button please follow the
steps above:
1. Unplug the Ethernet cable. 2. Locate the reset hole on the back panel of
your HT812/HT814. 3. Insert a pin in this hole, and press for about 7 seconds.
4. Take out the pin. All unit settings are restored to factory settings
Using the IVR Command
Reset default factory settings using the IVR prompt:
1. Dial “***” for voice prompt. 2. Enter “99” and wait for “reset” voice
prompt. 3. Enter the encoded MAC address (Look below on how to encode MAC
address). 4. Wait 15 seconds and device will automatically reboot and restore
factory settings.
Encode the MAC Address
1. Locate the MAC address of the device. It is the 12-digit HEX number on the
bottom of the unit. 2. Key in the MAC address. Use the following mapping:
Key
Mapping
0-9
0-9
A
22 (press the “2” key twice, “A” will show on the LCD)
B
222
C
2222
D
33 (press the “3” key twice, “D” will show on the LCD)
E
333
F
3333
Table 12: MAC Address Key Mapping For example: if the MAC address is 000b8200e395, it should be keyed in as “0002228200333395”
Reset from Web Interface (Reset Type)
1. Access your HT812/HT814 UI by entering its IP address in your favorite
browser. 2. Enter your admin password (default: admin). 3. Press Login to
access your settings. 4. Go to Basic Settings Reset Type 5. Press Reset button
(after selecting the reset type).
· Full Reset: This will make a full reset
· ISP Data: This will reset only the basic settings, like IP mode, PPPoE and
Web port
· VoIP Data Reset: This will reset only the data related with a service
provider like SIP server, sip user ID, provisioning and others.
Factory Reset will be disabled if the “Lock keypad update” is set to “Yes”.
If the HT812/HT814 were previously locked by your local service provider,
pressing the RESET button will only restart the unit. The device will not
return to factory default settings.
Reset using SIP NOTIFY
1. Access your HT812/HT814 UI by entering its IP address in your favorite
browser. 2. Go to Profile # page. 3. Set “Allow SIP Factory Reset” to “Yes”.
(Default is No) 4. Once a SIP NOTIFY with “event: reset” is received, the ATA
will perform factory reset.
Received SIP NOTIFY will be first challenged for authentication purpose before
taking factory reset action. The authentication can be done either using admin
credentials (if no SIP account is configured) or using SIP account
credentials.
CHANGE LOG
This section documents significant changes from previous versions of the admin
guide for HT812/HT814. Only major new features or major document updates are
listed here. Minor updates for corrections or editing are not documented here.
Firmware Version 1.0.47.4
Added IVR support to check Device Individual Certificate Information.
[Interactive Voice Prompt Response Menu] Added support “https://” in Config
Server Path field. [Config Server Path] Added support “https://” in Firmware
Server Path field. [Firmware Server Path] Added support configure RFC2833
Events Count to 0, 0 means continuous RFC2833 events. [RFC2833 Events Count]
Added support Inband DTMF TX Gain. [Inband DTMF TX Gain] Added support to
disable the “CDR File Option”. [CDR File Option] Added support Special
Condition Tone. [Call Progress Tones] Added support Incoming Call Duration
Limit. [Incoming Call Duration Limit] Added support “Port Voltage Off upon no
SIP Registration or SIP Registration Failure” and “Delay Time of Port Voltage
Off Timer Since Boot”. [Port Voltage Off Timer] Added LAN Port VLAN Feature
Under Bridge Mode on HT812 and HT814. [LAN Port VLAN Feature Under Bridge
Mode] Firmware Version 1.0.45.2
Added override config file option “cfgMAC_override.xml”. [cfgMAC_override.xml]
Added option “Download and Process All Available Config File. [Download and
Process All Available Config Files] Added option “When To Restart Session
After Re-INVITE received” [When To Restart Session After Re-INVITE received]
Updated the option in “Unregister On Reboot” to 0 No, 1 All, 2 Instance.
[Unregister On Reboot] Firmware Version 1.0.43.11
Added Charter CA to the approved certificate list. [Load CA Certificates]
Added support for TR-069 on the management interface. [Enable TR-069 Through
Management Interface] Added ability to send Syslog traffic through Management
Interface.[Enable Syslog Through Management Interface] Added support for
variable on Provisioning link. [Enable Using tags in URL] Updated the default
option of “Disable Reminder Ring for DND” to “Yes”. [Disable Reminder Ring for
DND] Add SSL Key Log File. [With Secret Key Information] Add Information
Capture. [Information Capture] Allow configuring devices through SSH from
different networks. [Security Controls for SSH/Telnet Access] Removed Telnet
Idle Timeout Configuration Option.[Telnet Idle Timeout] Added additional Flash
Digit events.[Flash Digit Control] Optimized the layout of the software
version on the status page to make it look better. Add support of DHCP Option
150. [Additional Override DHCP Option] Merge DHCP Option 160 with DHCP Option
66. [Allow DHCP Option 66 or 160 to Override Server] Add a new special feature
option “GIBTELECOM”. [Special Feature] Add support for the “From Domain”
option. [From Domain] GUI enhancement to display correctly port status. Added
support for SRTP Key Length. [SRTP Key Length] Increased Admin/User/Viewer
Password length to 30 characters. [User/Viewer Password] [Admin Password]
Added support for Inband DTMF Duration. [Inband DTMF Duration] Added support
for DSP DTMF Detector Duration Threshold. [DSP DTMF Detector Duration
Threshold] Added new attribute values on WebUI:
TR-069 firewall rules (Value Range:1-65535, no default). [TR-069 firewall
rules] Root CA Version (0 Current Root; 1 New Root, default is 1) [Root CA
Version] Provision and upgrade to new Gen-2 certificate. (1- upgrade; 0 no
upgrade, default is 0). [Gen-2 certificate.] Contents (text string) of Gen-2
certificate to upgrade. (String. Max length 8192, no default). [Gen-2
certificate.] Contents (text string) of Gen-2 EC private key to upgrade.
(String. Max length 8192, no default) [Gen-2 EC private key] Disable filename
in URL for config provision. [Configuration File Download] Disable filename in
URL for firmware upgrade. [Firmware Upgrade procedure] Firmware Version
1.0.41.2
Updated Time Zone option “GMT+01:00 (Paris, Vienna, Warsaw)” to “GMT+01:00
(Paris, Vienna, Warsaw, Brussels)”. [Basic Settings Page Definitions] Added
star code [*98] to play registration ID.
Firmware Version 1.0.39.4
Added feature to send SNMP traffic through Management Interface. [Basic
Settings Page Definitions] Added feature to re-subscribe only after a
configurable timeout after receiving 403. [Profiles Page Settings] Added
feature support e911 compliance and HELD protocol. [Advanced Settings Page
Definitions] Updated the default value of “Maximum Number of SIP Request
Retries” from 4 to 2. [Profiles Page Settings] Updated CDR File Option | SIP
File Option (P8534/8535) value from “1 Override” to “Overwrite”. [Advanced
Settings Page Definitions] Added Local IVR option that announces extension
number of the port. [Understanding HT812/HT814 Interactive Voice Prompt
Response Menu] Firmware version 1.0.37.1
Added feature Configuration File Types Allowed. [Advanced Settings Page
Definitions]. Added feature MAC in User-Agent [Profile Page Definitions] Added
feature Use MAC Header [Profile Page Definitions] Firmware Version 1.0.35.4
Added support to allow HT8xx provision admin password without special
characters. Added support for Israel time zone with DST.
Firmware Version 1.0.33.4
Added feature Special Proceed Indication Tone. [Special Proceed Indication
Tone]. Added feature MWI Tone. [MWI Tone].
Firmware Version 1.0.31.1
Added support to always send HTTP Basic Authentication Information. [Always
Send HTTP Basic Authentication Information] Added support to Enable Call
Waiting Alert-Info in 180 Ringing Response. [Enable Call Waiting alert-info In
180 Ringing Response] Firmware Version 1.0.29.8
Added support to authenticate based on OpenVPN Username and OpenVPN Password.
[OpenVPN Username and OpenVPN Password] Added feature “OnHook DC Feed Current”
[OnHOOK DC Feed Current] Firmware Version 1.0.27.2
No Major Changes
Firmware Version 1.0.25.5
Added support for “OpenVPN”. [OpenVPN] Added support of “Maximum Number of SIP
Request Retries”. [Maximum Number of SIP Request Retries] Added support for
“Failback Timer”. [Failback Timer] Firmware Version 1.0.23.5
Added Special Feature IZZI to support N-Way conference hosted on Nokia IMS.
Added support for “DNS SRV Failover Mode”. [DNS SRV Failover Mode] Added
support of “Register before DNS SRV Failover”. [Register before DNS SRV
Failover] Firmware Version 1.0.21.4
Added support for IPv6 address without square brackets. [Primary SIP
Server][Failover SIP Server][Outbound Proxy] [Backup Outbound Proxy] Added
support for DHCP Domain Name configuration. [DHCP domain name] Added support
of “Use Configured IP” for “DNS Mode”. [Use Configured IP] Added support for
“Play Busy Tone When Account is unregistered”. [Play Busy Tone When Account is
unregistered] Firmware Version 1.0.19.11
Added “Disable” option for “Web Access Mode” feature. [Web Access Mode] Moved
“Trusted CA certificates” from ProfileX to Advanced Settings and renamed as
Trusted CA Certificates A and Trusted CA Certificates B. [Trusted CA
Certificates (A,B)] Added feature “Disable User Level Web Access” and “Disable
Viewer Level Web Access”. [Disable User Level Web Access ] [Disable Viewer
Level Web Access] Added feature “Use P-Asserted-Identity Header”. [Use P
-Asserted-Identity Header] Added feature “Load CA Certificates”. [Load CA
Certificate] Added support to configure TR-069 connection request port.
[Connection Request Port] Added OI_BR to special feature. [Special Feature]
Added New Zealand Standard for Pulse Dialing Standard. [ Pulse Dialing
Standard] Added support to set Ring Timeout to 0 for unlimited ring timeout.
[Ring Timeout] Increased “SIP TLS Certificate” and “SIP TLS Private Key”
supported maximum length from 2048 to 4096. [SIP TLS Certificate][SIP TLS
Private Key]
Firmware Version 1.0.17.5
Added feature “Minimum TLS Version”. [Minimum TLS Version] Added feature
“Maximum TLS Version”. [Maximum TLS Version] Updated “São Paulo” time zone to
UTC-3. [Time Zone] Firmware Version 1.0.15.4
Added more choices to feature “Disable Weak TLS Ciphers”. [Disable Weak TLS
Cipher Suites] Added feature “Syslog Protocol”. [Syslog Protocol] Added
support for “Distinctive Call Waiting Tone”. [Distinctive Call Waiting Tone]
Added support for “Call Waiting Tones”. [Call Waiting Tones] Added support for
DHCP option 67. [Configuration File Download] Added support to allow CID name
fields for ports that are part of the active hunting group to take effect.
[Hunting Group] Added support for GDMS. [ACS URL] Firmware Version 1.0.13.7
Added ability to support provisioning server path containing the server
authentication credentials for the DHCP option 66. [Allow DHCP Option 66 to
Override Server] Added support to send SNMP trap to 3 different servers. [SNMP
Trap IP Address] Added feature “Call Features Settings”. [Call Features
Settings] Added feature “Use SIP User Agent”. [SIP User-Agent] Updated “Use
SIP User Agent Header” to “SIP User Agent Postfix”. [SIP User Agent Postfix].
Added feature “Disable Reminder Ring for DND”. [Disable Reminder Ring for DND]
Added feature “CDR File Option”. [CDR File Option] Added feature “SIP File
Option”. [SIP File Option] Added feature “Disable Weak TLS Cipher Suites”.
[Disable Weak TLS Cipher Suites] Added feature “Pulse Dialing Standard”.
[Pulse Dialing Standard] Added feature “Callee Flash to 3WC”. [Callee Flash to
3WC] Added feature “RFC2833 Count”. [RFC2833 Events Count] [RFC2833 End Events
Count] Added feature “Replace Beginning +’ with 00 in Caller ID”. [Replace Beginning
+’ with 00 in Caller ID] Added feature “Reset Call Features”.
[Reset Call Features] Added support to view, download, and delete the call
history through device Web UI. [CDR File] Added support to store SIP file
locally. [SIP File] Firmware Version 1.0.11.6
Added “CPU Load” on Web UI status page [CPU Load] Added support for SIP keep-
alive to use SIP NOTIFY. [Enable SIP OPTIONS/NOTIFY Keep Alive] Added feature
“Network Cable Status” on Web UI status page. [Network Cable Status] Added
support for Management Interface. [Management Interface] Added feature “SSH
Idle Timeout”. [SSH Idle Timeout] Added feature “Telnet Idle Timeout”. [Telnet
Idle Timeout] Added feature “Use ARP to detect network connectivity”.[Use ARP
to detect network connectivity] Added feature “Call Record”.
Firmware Version 1.0.10.6
Added feature “Inband DTMF Duration”. [Inband DTMF Duration] Added feature
“RFC2543 Hold”. [RFC2543 Hold] Added feature “Visual MWI Type”. [Visual MWI
Type] Added feature “Disable Unknown Caller ID”. [Disable Unknown Caller ID]
Added feature “Disable # as Redial Key”. [Disable # as Redial Key] Added
feature “Ring Frequency”. [Ring Frequency] Added feature “Allow SIP Factory
Reset”. [Allow SIP Factory Reset] [Reset using SIP NOTIFY] Added support for
G722 Codec. [HT812/HT814 Technical Specifications] Added support to allow user
to choose preference codec from PCMU and PCMA for FAX pass-through codec. [Fax
Mode] Added Web menu in Spanish. [Language] Firmware Version 1.0.9.3
Added feature “Custom Certificate”. [Custom Certificate] Added feature “Use P
-Access-Network-Info Header”. [Us
References
- Grandstream Firmware
- Gaps
- FreeDNS - Free DNS - Dynamic DNS - Static DNS subdomain and domain hosting
- Index of /gs
- Welcome! - The Apache HTTP Server Project
- Free Dynamic DNS - Managed DNS - Managed Email - Domain Registration - No-IP
- not.tel
- number.By
- 花生壳动æ€åŸŸå解æžæœåŠ¡-è´é”官网|花生壳官网|DNS内网穿é€|域å注册|å‘日葵远程控制|远程桌é¢|蒲公英路由器-è´é”官网
- pool.ntp.org: the internet cluster of ntp servers
- seconds.no
- RingByName – Cloud-Based Phone Service and VOIP Provider
- TFTPD64 : an opensource IPv6 ready TFTP server/service for windows : TFTP server
- Firmware- Grandstream Networks
- Tools- Grandstream Networks
- FREE TFTP Server and SFTP/SCP Server | SolarWinds
- DNS Hosting, Dynamic DNS and Domain Management with Zoneedit – The Original DNS Provider
- HT80x - Administration Guide - Documentation Center
- documentation.grandstream.com/knowledge-base/ht812-ht814-administration-guide/?hkb-redirect&nonce=7cef868c51&check=6tash&redirect=helpdesk.grandstream.com&otype=ht_kb_article&oid=68786&source=widget
- Welcome! - The Apache HTTP Server Project
- About Us
- Contact Us
- Newsletter Sign Up
- Firmware- Grandstream Networks
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>