Rapid BGX7 BATTERY GLUE GUN Instruction Manual

BGX7 BATTERY GLUE GUN
Instruction Manual

GENERAL POWER TOOLS SAFETY WARNINGS

WARNING!!
Read all safety warnings and all instructions. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury.
Save all warnings and instructions for future reference.
The term ”power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1. WORK AREA SAFETY
   a) Keep your work area clean and well-lit. Cluttered benches and dark areas invite accidents.
   b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks that may ignite dust or fumes.
   c) Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control.

2. ELECTRICAL SAFETY
   a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock.
   b) Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded.
   c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
   d) Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool. Keep cord away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increase the risk of electric shock.
   e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. The use of a cord suitable for outdoor use reduces the risk of electric shock.
   f) If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter protected supply. The use of a ground fault circuit interrupter reduces the risk of electric shock.

3. PERSONAL SAFETY
   a) Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
   b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust masks, non-skid safety shoes, hard hats, or hearing protection used for appropriate conditions will reduce personal injuries.
   c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to a power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
   d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
   e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
   f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
   g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. The use of dust collection can reduce dust-related hazards.

4. POWER TOOL USE AND CARE
   a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate at which it was designed.
   b) Do not use the power tool if the switch does not turn on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
   c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
   d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
   e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
   f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
   g) Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

5. SERVICE
   a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

BATTERY GLUE GUN SAFETY WARNINGS
WARNING:

• This tool must be placed on its stand or foot when not in use.

• A fire may result if the appliance is not used with care, therefore
  • be careful when using the appliance in places where there are combustible materials;
  • do not apply to the same place for a long time;
  • do not use in presence of an explosive atmosphere;
  • be aware that heat may be conducted to combustible materials that are out of sight;
  • place the appliance on its stand after use and allow it to cool down before storage;
  • do not leave the appliance unattended when it is switched on.

• Do not use or store the tool in damp or wet conditions.

• Do not expose it to water or other fluid substances in any way.

• Do not use the tool if any part is damaged or defective.

• Hot surface: Both the glue and the nozzle of the tool can reach temperatures up to 170°C.

• Avoid all skin contact. If burnt, plunge the burn under cold water. Never attempt to remove solidified glue from burnt skin without medical assistance.

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.

• Children shall not play with the appliance.

• Cleaning and user maintenance shall not be made by children without supervision

BATTERY SAFETY WARNINGS

• Never attempt to open for any reason.
• Do not expose the battery and tool to water and any other liquids.
• Do not expose the battery to heat or fire. There is a risk of explosion
• Do not store in locations where the temperature may exceed 40°C.
• Charge only at ambient temperature between 10°C and 40°C.
• Charge only using the charger provided with the tool.

CHARGER AND USB CABLE SAFETY WARNINGS

• The charger is double insulated therefore no earth wire is required.
• Always check that the mains voltage corresponds to the voltage on the rating plate.
• The charger is intended for indoor use only.
• Use your charger only to charge the battery in the tool with which it was supplied.
• Do not expose the charger to water.
• Do not open the charger.
• The appliance is only to be used with the USB cable unit provided with the appliance
• If the power supply cable is damaged it must be replaced by the manufacturer, the manufacturer’s after-sales service, or a similarly qualified person in order to avoid any danger.

TECHNICAL SPECIFICATION

Lithium-Ion battery-operated glue gun

The manufacturer reserves the right to change specifications without notice.
USB charger

TECHNICAL FEATURES

A: On/Off button
B: Tool LED light (green/Red)
C: Nozzle
D: USB Socket
E: Trigger
F: Tool stand
G: Charge
H: USB cable

USAGE

• Before using it for the first time, fully charge the battery (3-4 hours) so as to prolong its life. (see Charging Instructions)
• Feed glue sticks into the rear of the tool.
• Use only Rapid glue sticks recommended.
• Press the on/off button for approx. 2 sec, Green LED will flash for approx. 20 sec, and remain green fix when ready for use.
• When using the tool for the first time, press the trigger several times to fill the heating chamber with adhesive. It may also be necessary to give the glue stick a short push to help it move in.
• Place the nozzle of the tool against the surface and press gently on the trigger to extrude glue.
• Place the second element in contact with the glue, if need be adjust it, and press parts together for an average of 10 seconds.
• Never pull/remove a glue stick from the tool once it has been fed into the tool. The resultant molten glue could create irreparable damage to the tool.
• Once finished, push the on/off button for approx. 2 sec.
• When the battery is almost discharged, the LED will alternately flash from red to green.
• For safety reasons if no use for approx. In 3 min, the glue gun will automatically switch it off.

Operation / Usage

LED Red| LED green|
| | Switch ON for approx 2 sec.
Green LED will flash for approx 20 sec. (pre-heating)
| | Applicator ready for Use.
Press the ON/OFF button for approx 2 sec to switch OFF the applicator when the job is finished
| | No use/gluing for approx 3 min :
glue gun automatically switches OFF for safety
Press the button ON to re-start
| | Red and green LED flashes alternately after the glue gun has been used for approx 25 min.
Battery almost empty applicator can now only be used for approx 5 min
Red flash only or no more LED: If the battery is empty, re-load it by using the USB charger
|
|

CHARGING INSTRUCTIONS

• Connect the USB cable onto the charger and micro USB socket at the back of the tool
• Connect the charger to the mains.
• The LED on the glue gun will flash red during the charge., and will turn to fix green when the battery is fully charged
• During the process of charging, the charger and glue gun can become warm, this is normal.

Charging with a USB charger

LED Red| LED green|
| | Battery is charging
| | The battery is fully charged

MAINTENANCE

• Unplug the tool before any maintenance.
• Keep the air intake and outlet free from dust and dirt.
• Clean the tool with a dry or damp cloth. NEVER use any solvent.
• DO NOT oil or grease any parts.
• Be sure the tool is not damaged. Replace or repair prior to use.

WARNING!

• DO NOT alter parts on this tool or attach special fixtures. This can lead to personal injury.

ENVIRONMENT!
Separate Collection. Do not dispose of power tools into household waste! According to the European Directive 2012/19/EC on the waste of electrical and electronic equipment.
When the tool needs to be replaced, or if it is of no further use it should be brought to a separate collection center for recycling. The appliance and the battery must be disposed of separately. To do this, unscrew/open the appliance, cut the battery connection cable and remove the battery from the appliance.

WARRANTY

Warranty period: This product is guaranteed for 2 years from the date of purchase (original sales receipt acting as proof).
Warranty conditions: All points mentioned in this document must have been fully adhered to.
In the event of a claim under the warranty:

1. Return the product in its original packaging to the shop or outlet that supplied you with this product,
2. Accompany the returned product with the original dated receipt.

Any breach of one of these points would prevent consideration by RAPID under the manufacturer’s warranty.

Isaberg Rapid AB. Metallgatan 5,
335 71 HESTRA, SWEDEN
www.rapid.com
Art. No 840109823 Mind & Join 2019-02-28

References

• Rapid Tools - fastening specialist

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>