SIMPLE DELUXE B08N4GMYQG 24 Inch Wall Mounted Fan Instruction Manual
- May 15, 2024
- SIMPLE DELUXE
Table of Contents
SIMPLE DELUXE B08N4GMYQG 24 Inch Wall Mounted Fan
Intended Use
- This product is intended for indoor residential, office, industrial, and other commercial applications.
- Use only electrical wiring that is in good working order and that meets applicable codes and ordinances.
- If you have any questions about whether your wiring is adequate, consult a qualified electrician.
- While using your fan, you should follow the IMPORTANT INSTRUCTIONS Stated below.
- As part of those instructions, we have used the word “WARNING to indicate the level of hazard:
- WARNING indicates a hazard that, if not avoided, could result in injury or death.
IMPORTANT INSTRUCTIONS
- As with all electrical appliances, basic safety precautions should always be followed to reduce the risk of electric shock, fire, or injury to persons, including the following precautions:
- Read all the instructions before using this fan.
- Use this fan only as described in this manual. Any other use not recommended by the manufacturer may cause electrical shock fire or injury to persons.
- Do not operate the fan with a damaged power cord or after the fan malfunctions or has been dropped in any manner.
- Use of extreme caution is necessary when any fan is used by or near children, disabled persons, or pets and whenever the fan is left operating unattended.
- Do not place the fan on a small, unlevel, uneven, or any surface that might allow the fan to tip or fall.
- For proper operation, the fan should be placed on a smooth, non-combustible, level surface.
- Always unplug the fan when not in use, when moving from place to place, when assembling or disassembling parts, and before cleaning.
- The use of attachments, not recommended or sold by the manufacturer, may cause hazards.
- Do not use outdoors.
- Do not use the fan in the window. Rain may cause electrical hazards (for non-window models).
- Do not operate the fan with blade guards or any safety device removed.
- Avoid the use of extension cords due to the risk of fire. If an extension cord must be used, the cord must be a minimum of 14 AWG and rated not less than 1875 waits.
- Do not run the power cord under the carpeting. Do not cover the cord with throw rugs, runners, or the like. Arrange the cord away from the traffic area where it will not be tripped over.
- Do not insert or allow any object to enter any openings on the fan. Doing so may cause electric shock and /or fire hazards.
- Avoid contact with moving parts.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure they do not play with the appliance.
WARNING: Shock Hazard
- Use your fan only in dry environments. This fan is not Intended for use in a bathroom, laundry area, or similar locations, or near sinks, washing machines, swimming pools, or other sources of water.
- Never locate a fan where it may fall into a bathtub or other water receptacle. Do not use it in damp environments such as flooded basements.
WARNING: Hot Surfaces
- Do not touch the fan motor when in use. This motor Is hot when in use, to avoid burns, do not let bare skin touch hot surfaces.
WARNING: Fire Hazard
- Fans have arcing or sparking parts inside. Do not use near combustible materials flammable gases or sources of heat
- DO NOT USE in areas where gasoline, paint, or flammable materials are used or stored.
- To prevent a possible fire, do not block air intakes or exhaust in any manner, Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock, fire, or damage to the fan.
WARNING: Electrical Shock Hazard
- Do not use a damaged cord or plug. Use with adequate electrical system that is up to code.
- CAUTION: To Prevent Electric Shock, this product has a three-prong grounded plug that must be inserted into a matching properly grounded outset to reduce the risk of electrical shock.
- Do not attempt to defeat this safety feature,
- WARNING: To reduce the Risk of Fire or Electric Shock, do not use this product with any solid-state speed control device.
- DO NOT operate any fan with a damaged card or plug or after fan malfunctions, has been dropped or damaged in any manner.
- Do not operate the fan with a broken blade, safety cage, or any visual imperfections. Disconnect power before servicing. For repairs covered under warranty, see warranty statement.
- For all other repairs contact Comfort Zone Customer Service by telephone or mail for information and assistance.
- DO NOT run the Power cord under the carpeting. DO NOT cover the cord with throw rugs, runners, or the like. Arrange the cord away from the traffic area where it will not be tripped over.
- Avold the use of extension cords due to the risk of fire.
- If an extension cord must be used, the cord must be a minimum of 14 AWG and rated not less then 1875 waits.
- Do not use an extension cord unless the plug can be completely inserted into its receptacle.
- Unplug the fan when not in use.
- Do not operate the fan with its ventilation obstructed.
- WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC, SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING.
- a) Installation work and electrical wiring must be done by a qualified person(s) under all applicable codes and standards, including fire-rated construction.
- b) When cutting or drilling into a wall or ceiling, do not damage electrical wiring and other hidden utilities.
Installation Instructions
- Use the following information as a guideline only. It is the user’s responsibility to be sure the location and the wall surface can handle the weight of this fan (14.6 lbs).
- The wall fan must be mounted on 12 inches (300mm)thick dry and cement-grouted firm wall or on 4 by 5-inch wood studs/ joists.
- Use a wall bracket as a template for locating the holes to be drilled.
- After determining the hole locations, use an appropriate-sized drill bit and, drill holes through the mounting surface.
- It is recommended that a minimum of grade 5 fasteners be used. The following are acceptable surfaces for mounting wall mount assembly.
- STEEL SURFACE – When mounting to a steel surface, such as a vertical l-beam, drill through holes at pre-marked locations, using a 9/32″ drill bit.
- Attach wall mount assembly to the mounting surface using 114″-20 hex screws, in combination with 114″ flat washers, 1/4″ Jock washers, and 1/4-20 hex nuts.
- MASONRY SURFACE – When mounting to a masonry surface use a 1/4″ expansion type bolt or 1/4* masonry lag with a shield designed to handle the weight of this fan.
- Drill holes at pre-marked locations using an appropriate-sized drill bit as recommended for the fastener.
Usage
- Fan operation: Always operate the fan in the upright position following all instructions and recommendations listed in this manual.
- Fan location: Place the fan in the area of the room that will provide proper fan cooling.
Fan connection:
- wall outlet. Be sure the plug fits tightly in the outlet. A loose connection may cause overheating and damage to the plug or fan.
- Note: To prevent overloading a circuit, do not plug the fan into a circuit that is servicing other electrical needs.
- Speed control: To separate the fan, each pull of the string will cycle through the following:
- OFF
- LOw
- MED
- HIGH
- OFF
Specifications
Care and Maintenance
- Cleaning: CAUTION- Before cleaning the fan be sure 1o disconnect the power cord from the plug. Clean the grille surface with a clean damp cloth.
- Do not use harsh chemicals or abrasive cleaners.
- DO NDT IMMERSE THE FAN OR ANY WIRES IN WATER. Replace the front grill before fan use.
- Allow the fan to dry completely before use. Periodic grille cleaning with a vacuum will prevent dust buildup.
- The motor is sealed and does no require any interior maintenance, cleaning, or lubrication.
- Maintenance: The internal motor bearings are permanently Eubricated at the factory and do not require any additional lubrication.
- Repair: DO NOT OPERATE THE FAN WITHOUT THE GRILLE IN PLACE. DO NOT USE THE FAN IF IT HAS MALFUNCTIONED OR BECOME DAMAGED IN ANY WAY.
- Storage: Keep the original carton for storage of the fan. Coil and tie the power cord to avoid damage during storage.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>