Simple Deluxe 16 Inch Pedestal Stand Fan with Remote Control Instruction Manual

Simple Deluxe 16 Inch Pedestal Stand Fan with Remote Control

READ AND FOLLOW ALL INSTRUCTION BEFORE OPERATING FAN

CAUTION
Read and follow all instruction before operating fan. Do not use fan if any part is damage or missing.

WARNING

1. To reduce the risk of fire or electric shock, do not use this fan with any solid state speed control device.
2. This appliance has a polarized plug which is intended to fit in an outlet only one way. If this does not fit outlet, contact a qualified electrician. Do not attempt to by-pass this procedure.
3. This product is to be used indoors.
4. Unplug from electrical supply source before cleaning.
5. If the power cord is damaged, contact your local service center or a qualified electrician to install an appropriate replacement cord to prevent any injuiry or damage.
6. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their aafety.
7. Children should be supervised to ensure that they do not play with the appliance.

RULES FOR SAFE OPERATION

1. Never insert fingers, pencils, or any other object through the guard when fan is running.
2. Disconnect the fan when moving from one location to another.
3. Disconnect the fan when removing grils for cleaning.
4. Be sure fan is on a stable surface when operating to avoid overturning.
5. DO NOT use fan in window. Rain may create electrical hazard.
6. The fan is for home use only.
7. Do not leave the fan running unattended.

ASSEMBLY

Before commencing assembly familiarize your self with all the assembly components (See chart and diagram}.

1. Put the bottom cover(12) on the base(13);
2. Install the teléscopic tube(11) on the base(13) and tighten it with screws(15);
3. Loosen the lifting knob(9) and install the decorative cover(14);
4. Loosen the fixing nut(10), mount the body(8) onto the telescopic tube(11), and lock the lifting knob(9);
5. Loosen reat grill securing ring(4) from the motor shaft pin(6);
6. Position rear grill(5) firmly to motor housing(7) and then fasten by turing reat grill securing ring clockwise till tightened;
7. Insert the fan blades(3) onto the motor shaft pin(6), securing the fan blades using the fan blade securing cap(2),turing counter-clockwise to tighten;
8. Install front gril(1) over top of the rear grill, fasten the two grills with the clips attached to the front grill(1);
9. Fully tighten the small nut and boltthat passes through the rim of the grill;
   Attention:Notches on fan blade assembly must be seated firmly on arms of fan shaft,Fasten retaining cap securely before use.

ASSEMBLY COMPONENTS

1. front grill
2. fan blade securing cap
3. fan blades
4. securing ring
5. rear grill
6. shaft pin
7. motor housing
8. Body
9. lifting knob
10. fixing nut
11. telescopic tube
12. bottom cover
13. Base
14. decorative cover
15.  screws

USING THE REMOTE CONTROL

1. The sensor of the remote control must be pointed at the fan receiver to operate properly;
2. The distance between the remote control and the fan should be within 20 feet and 45 degrees radius left to right of fan;(see Fig.2)
3. See the button functions as they appear on the remote control in; (Fig 3)

TIMER

Press the Timer button repeatedly to change the timer setting. The time increase in increments of 0.5 hours and it has 4 time steps in total, which add up to set your desired timer setting. The maximum timer is 7.5 hours.
For example, to set time for 5 hours, press the timer button repeatedly till the indicator lights “1h” and “4h” are lit at the same time.
Do not press the Timer button if you want to keep the fan operating indefinitely-the timer indicator lights will not light up if the timer button is not pressed.

SPEED
After pressing the SPEED button,use +/- to increase or decrease the SPEED.

OSCILLATION
When you press this button, the fan oscillated at 0-90 degrees. Press the osoillation button again if you want to keep the fan operating in one position. The fan will only oscillate when the Oscillation(Swing) button has been pressed.
Do not adjust the head of the fan manually or oscillation parts could be damaged.

ON/OFF
Press the ON/OFF button to turn ON or OFF the fan.
Press + or – button to adjust speed..

USING THE CONTROL PANEL
The button names and functions are shown on the control panel in Fig. 3. uncon oNe yand ran pro the anthe Son the Remote Control.

FUNCTION MODES

This fan has three different modes: NORMAL, NATURAL BREEZE and SLEEP. Each mode functions differently. For example, the NORMAL mode has 3 speeds (HIGH- MIDDLE- LOW”), with “HIGH” creating the most airflow and “LOW” creating the least airflow.
The NATURAL BREEZE mode also has 3 speeds which are the same as the NORMAL mode but they have a different function. This mode will simulate a breeze by generating the desired speed (“HIGH-MIDDLE-LOW”), then slowing down to a very low speed and then generate your desired speed again in a continuous manner.
The SLEEP mode functions in the same way as the NATURAL BREEZE mode but it is timed to slow down to a lower speed after a certain period of time. During the SLEEP mode the speed will change as follows:

High Speed:
The fan will operate like the NATURAL BREEZE mode for 30 minutes at high speed, then operate like the NATURAL BREEZE mode for 30 minutes at medium speed and then finally operate like the NATURAL BREEZE mode at low speed for the remainder of the time in which the fan is turned on.

Medium Speed:
The fan will operate like the NATURAL BREEZE mode for 30 minutes at medium speed and then operate like the NATURAL BREEZE mode at low speed for the remainder of the time in which the fan is turned on.

Low Speed:
The fan will operate like the NATURAL BREEZE mode continuously in low speed.

• To adjust the tilt angle of fan head upward or downward by simply moving the guard up or down.

USER SERVICING INSTRUCTIONS

1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord
2. Open fuse cover. Slide open fuse access cover on top of attachment plug towards blades, (see fig. 5)
3. Remove fuse carefully. Remove the fuse by prying it out carefully. (see fig. 6)
4. Risk of fire. Replace fuse only with 5Amp max, 125 Volt fuse.
5. Close fuse cover. Slide closed the fuse access cover on top of attachment plug. (see fig-7).
6. Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged.

Tips: Do not overexert when replacing the fuse or damage may occur. If it’s hard to close the access cover. make sure the fuse is fully inserted.

CLEANING

1. Be sure to unplug from the electrical supply source before cleaning.
2. Plastic parts should be cleaned with mild soap and damp cloth or sponge. Thoroughly remove soap film with clean water.
3. Be sure not to get water or other liquid into the motor.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>