TECLAST Mini PC User Manual
- June 4, 2024
- TECLAST
Table of Contents
TECLAST Mini PC
What’s in the Box
- Power cords vary by country
- Some models may contain some accessories not listed
Size（In)
How to Use
- Insert the DC power plug on the adapter into the power input jack (DC).
- Connect the AC adapter plug to the AC/DC adapter.
- lug the AC adapter into a power outlet.
- Press the power button on the Mini PC.
Can be placed flat or upright
Ports of Product
Front Ports
Back Ports
Care During Use
Please read this manual before operating the product. The manual should be kept for future reference.
Notice:
- Any changes or modifications not approved by the competent authority may make the user unable to operate this product.
- In order to comply with the radiation limit, shielded signal cables and AC power cables must be used.
- The manufacturer is not responsible for any radio or electrical interference caused by unapproved modifications, and it is the user’s responsibility to correct such interference.
Warning:
In order to prevent fire or explosion, do not expose the product to rain or
moisture. There is a dangerous high voltage inside the product. Please be
careful when using and installing it. If you need maintenance, you should seek
professional personnel.
Precaution
- Do not keep the product near water sources such as bathrooms, dishwashers, kitchens, washing machines, swimming pools or wet basements.
- Do not place the product on unstable cars, chairs, and tables.
- Do not cover the ventilation holes on the product.
- Please make sure to use a three-hole grounded socket
- When the product is not used for a long time, please cut off the power supply.
- Do not overload the socket, otherwise it will cause fire or electric shock.
- Do not put foreign objects into the machine, it can cause short circuit and cause fire or electric shock.
- Do not open the casing to avoid high voltage or other dangers. If there is any fault, please contact the after-sales service personnel directly.
- To ensure safe work, please ensure that the power input voltage is consistent with the nameplate
Common Problems and Solutions
Q1: What should I do if it doesn’t boot up?
A1: 1. Check if the power supply is powered on.
2. Please tell Amazon to contact us directly to figure out the problems for
you.
Q2: How do I install or update drivers?
- Right-Click “This PC” and Select “Manage”
- Then click “Device Manager” in the left menu list
- Find the drivers you want to update
Q3: What if it cannot connect to the WiFi?
- Turn on the wifi hotspot of your mobile phone and see if you can connect to it.
- Please use your mobile phone to connect to the router wifi to test whether the router works normally.
- If there is no problem with the above, please insert the wired network cable to check whether the machine can access the Internet normally
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>