Oakcastle CD-20 Portable CD and Cassette Player User Manual

Oakcastle CD-20 Portable CD and Cassette Player

PRECAUTIONS BEFORE USE

KEEP THE5E INSTRUCTIONS IN MINO:

1. Do not cover or block any vent ilation openings. When placing the device on a shelf. leave 5 cm (2~) free space around the whole device

2. Install in accordance with the supplied user manual.

3. Keep the device away from heat sources such as radiators, heaters. stoves, candles and other heat•generating products or naked flame. The device can only be used in moderate climates. Extremely cold or warm environments should be avoided. Working temperature between o• and 35•c .

4. Avoid using the device near strong magnetic fields

5. Electrostatic discharge can disturb normal usage of this device. If so. simply reset and restart the device following the Instruction manual. During file transmission, please handle with care and operate in a static-free environment.

6. Warning! Never insert an object into the product through the vents or openings. High voltage flows through the product and inserting an object can cause electric shock and/or short circuit internal parts. For the same reason, do not spill water or liquid on the product.

7.  Do not use in wet or moist areas such as bathrooms, steamy kitchens or near swimming pools.

8.  The device shall not be exposed to dripping or splashing and make sure that no objects filled with liquids. such as vases,
   are placed on or near the apparatus.

9. Do not use this device when condensation may occur. When the unit is used in a warm wet room with damp, water droplets or condensation may occur inside the unit and the unit may not function properly; let the unit s1and in power OFF for 1 or 2 hours before turning on the power: the unit should be dry before getting any power.

10. Atthough this device is manufactured with the utmost care and checked several times before leaving the factory, it Is still possible tha t problems may occur, as with all electrical appliances. If you notice smoke, an excessive build-up of heat or any other unexpected phenomena. you should disconnect the plug from the main power socket immediately.

11. his device must operate on a power source as specified on the specification label. If you are not sure of the type of power supply used in your home. consult your dealer or local power company.

12. Keep away from animals. Some animals enjoy biting on power cords.

13. To clean the device. use a soft dry cloth. Do not use solvents or petrol based fluids. To remove se’llere stains, you may use a damp cloth with dilule detergenl.

14. The supplier is not responsible for damage or lost data caused by malfunction, misuse. modtficauon of the device or battery replacement.

15. Do not interrupt the connection when the device is formatting or transferring files. Otherwise, data may be corrupted or lost.

16. lf the unit has use playback function, the use memory stick should be plugged Into the unit directly. Don’t use an use extension cable because it can cause interference resulting in failing of data.

17. The rating label has been marked on the bottom or back panel of the device.

18. Thls device is not intended for use by people (including children) with physical, sensory or mental disabilities. or a lack of experience and knowledge, unless they’re under supervision or have received instructions about the correct use of the device by the person who is responsible for 1heir safety.

19. This product is intended for non professional use only and not for commercial or industrial use.

20. Make sure the unit Is adjusted to a stable position. Damage caused by using this product in an unstable position vibrations or shocks or by failure to follow any other warning or precaution contained within this user manual will not be covered by warranty ..

21. Never remove the casing of this device.

22. Never place this device on other electrical equipment.

23. Do not allow children access to plastic bags.

24. 0nly use auachmentslaccessories specified by the manufacturer.

25. Refer all servicing to quali fied service personnel. Servicing is required when the device has been damaged in any way, such as the power supply cord or the plug, when liquid has been spilled or objects have fallen into the device, when the device has been exposed to rain or moisture, does not operate nor malty, or has been dropped.

26. Long exposure to loud sounds from personal music players may lead to temporary or permanent hearing loss

27. lf the product is delivered with power cable or AC power adaptor:

    • If any trouble occur, disconnect the AC power cord and refer servicing to qualified per sonnel.
    • Don’t step on or pinch the power adaptor. Be very careful, particularly near the plugs and the cable’s e xit point. Do not place heavy items on the power adaptor, which may damage it. Keep the entire device out of children’s reach! When playing with the power cable, they can seriously Injure themselves.
    • Unplug this device during lightning storms or when unused for a long period.
    • The socket outlet must be installed near the equipment and must be easily accessible.
    • Do not overload ac outlets or extension cords. Overloading can cause fire or electric shock.
    • Devices with class 1 construction should be connected to a main socket outlet with a protective earthed connection.
    • Dovicos with class 2 construction do not roquiro a oarthed connection.
    • Always hold the plug when pulling it out of the main supply socket. Do not pull the power cord. This can cause a short circuit.
    • Do not use a damaged power cord or plug or a loose oullet. Doing so may result in fire or electric shOck.

28. 11 the product contains or is delivered with a remote control containing coin/cell batteries:
    Warning:

    • “Do not ingest battery, Chemical Burn Hazard” or equivalent working.

    • JThe remote control supplied with) This product contains a coin/button cell battery. If the battery is swallowe~. i1 can
      cause severe internal burns in Just 2 hours and can lead to death

    • Keep new and used batter ies away from children.

    • If the baltery compartment does not close securely, stop using the product and keep it away from children.

    •  If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medica attent on

Caulion about the use of Batteries:

• * Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

  • Battery cannot be subjected to high or low extreme temperatures, low air pressure at high altitude during use , storage or transportation.
  • Replacement of a battery with an incorrect type that can result in an explosion or the leakage o f flammable liqu d or gas.
  • Disposal of a battery into fire or a hot oven. or mechanically crushing or cutting of a battery, that can result irtan explosion.
  • Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or that leakage of flammable liquid or gas.
  • A battery subjected to extremely low air pressure that may result in an e xplosion or lhe leakage of flammable liquid or gas.
  • Attention should be drawn to the environmental aspects of battery disposal.

INSTALLATION

• *       * Unpack all parts and remove protective material.

  • Do not connect the unit to the mains before checking the mains voltage and before all other connections have been made.

FEATURES AND CONTROLS

Product Review and Accessories

1. VOLUME knob
2.  FUNCTION select button
3. 3.5mm headphone socket
4. PROG. button (CO/FM)
5. Telescopic antenna
6. REPEAT button (CO)
7. Carrying handle
8. STOP ■ button (CD)
9. CO compartment lid
10. PREV/- I<◄ button (CD/FM)
11. TUNING dial
12. PLAY/PAUSE ►II button (CO)
13.  PAUSE button (cassette)
14. NEXT/+ … button (CO/FM)
15. STOP/EJECT button (cassette)
16. LCD display
17. F.FWD button (cassette)
18. Cassette compartment
19. RWO button (cassette)
20. Speakers
21. PLAY button (cassette)
22. AC IN socket
23. RECORD button (cassette)
24. Battery compartment
25. POWER <!) button
26. Detachable power cord

BEFORE FIRST USE

Unpacking

• *       * Remove all packagmg.

  • ~ keep the ped(aglng. The product can be stewed in it if it is not used fa e klngor penod tune.
  • lace the product one level, stable, clean and dry suface.
  • Do not remove any labels or stickers on the back parEts at the fflEWl t.nl

Power supply
NOTE: Do not use the product with socket outlet and batteries at the same time. Remove batteries before connecting the product to mains powe

• *       * Remove 811 packagmg.

  • Do not plug or unplug the power coble in wet hands.
  • P1eose keep the packaging. The product con be stored in it if ii is not used for a longer period lime.
  • lnsort the power coble into AC soeket at the back of product. Connect the power plug too suilable electrical outlet. Moke sure that tho power st.WY voltage is the same as needed for the product.

Battery operation

• *       * Open the battery cornpEWtment at the bottom of the product.

  • Insert 6 batteries (1’ZI/=: , 8 X 1.5V, type C) (not supplied) according to lo the polarity markings Ins.de the batl8fy con1)8rtment and on the batteries.

  • Use bottines of high quality only. Batteries of low-quality might leak and C8US8 damage. Do not use new and ad
    batteries together Oose the con1)8rtmenl lid after inserting the batteries.

  • The produced IS is now ready for operation

  • IMPORTANT Do not use the product with an electrical out end batteries et the same time Remove batteries
    before conceding the product to mains power and remove the cable 1f the product tS be powered by batteries.

  • The product DNR.vs a 5m811 moot of power even if ii is not tuned on. If )’01.J do not use the product for long
    period of me, dlSCOm9Cl the power plug a removable battery.

  • The batteries shall not be exposed to excessive heat such as sunshine, fire or the like

    • The \/Oh.mo decreases, or SOUld is distorted during operation.
    • Remove the batteries 1f they are exhausted.

OPERATING INSTRUCTIONS

1. Switching On and Off
   • Power the product on: Press the POWER <!) button, the LCD display lights up. When the CD mode is selected while no CD is inserted, the LCD display Mashes – – , then shows “nocd’ steadi ly.
   • Power the product off: Press the POWER <!) button, the LCD display go off_ To CX>n1)1elely off the product, d iscomect the IX)Wef’ plug from the electrical outlet or rerTIO\le the batteries

Setting Volume Level

• Adjust the volume by rotating the VOLUME knob
  CAUTION: High volumes may cause ireparable damage to your hearing.

FM Radio Operation
Manual Station Selection
The product is equipped with a telescopic antenna located at the back of the product. Pull out the antenna completely and rotate to achieve the best FM channel reception. Press the FUNCTION button to select “FM mode. The LCD will show ‘FM along with the radio frequency scale. Rotate the TUNING knob or press the PREVI R or NEXT/+ PH button step by step to turn to the desired radio stations.
Search Station Operation
Scroll the TUNING knob to quickly reach the desired frequency. Or press and hold the PREVI- R or NEXT+ button for approx. 1 second, it will start to search the next radio station in the direction of the search. The search operation simply finds stations with strong signals. Stations with weak reception can only be tuned in
FM Stereo
When turning to an FM Stereo Broadcast, ‘ST will be shown on the LCD display.

Memorize Radio Stations (Manually)
Tune to the desired station. Long press PROG button, the LCD display will show PO1′ and PROG’ is flashing. Press PREVI- K or NEXT/+ button and select the desired number of your program. Press PROG button to store the radio station in the memory. Repeat steps above to store more tracks in memory. You can store up to 20 radio stations in the memory. If another station is already assigned to the selected preset number, that station is replaced by the new one.
Memorize Radio Stations (Automatically)
Long press PLAY/PAUSE I button, the radio will simply finds stations with strong signals, these stations are stored in memory from lower frequencies to higher ones. You need to memorize a station with a weak signal manually. 3.6 Select the Radio Stations in the Progarm (Program Play) Press PROG buttorn for the radio station memory and press PREV1- KM or NEXT/+ H button through the programmed station, the display will show ‘PO1′, P02’.etc., select the number to listen to the programmed stations.

CD Operation
This product reads CD, CD-R/-RW discs. Other discs are not supported by this product.

• When playing CD-R/-RW dics the playback quality might be influenced by the quality of the burned disc. When buming CD-R/ RW disks with audio files it is recommended to use the slowest burning speed.
• The product automatically power off about 15 minutes after
  • finishing last playback for CD operation
  • pressing the PLAY/PAUSEII button to pause playback
  • pressing the STOPbutton to stop playback

Inserting and Removing a CD

• Flip the carrying handle back before open the CD compartment lid.
• Set the FUNCTION button to the CD mode. The LCD display flashes’
• NOTE : Press the STOP button before rernovmg the CO inside.
• Duim n1- l!Ues can be searched using the PREV/- ~ or NEXT/+ ~ button or SCOl111ng 1\JNING knob
• In stop mode· Press the STOP ■ button The total number o( the tracks on the CD IS dtspleyed. The PREY/ – or NEXTI+ button can be used to skip between backs Press the PLAY/PAUSE ►II bu.ton to start playbock after the desued track ,s sekM::led

Programmed Playback

• The product can program up to 20 tracks for CD discs in any desired order.
• Press the STOP key to stop playback.

NOTE: Press the STOPbutton anytime using programming to cancel all previous programming and start over.
Repetition and Random Playback of Tracks

• The repeat function allows repeated playback of a track or the entire content of a disc during normal playback or programmed playback. Press REPEAT button to activate one of the following functions.
• Press the REPEAT button during normal playback or programmed playback to repeat the tracks.

4.5 Compact Discs

• Treat compact discs carefully. Handle them only by their edges. Never touch the shiny, unlabelled side of the disc by your fingers.
• Only hold the CD on the edges.
• Do not put adhesive tape, stickers etc. on either side of a disc.
• Clean discs periodically with soft, lint-free and dry cloth. Never use detergents or abrasive cleaners to clean discs. If it is necessary, use a CD cleaning kit
• Ifa disc skips or gets stuck during playback, it is probably dirty or damaged.
• When cleaning a disc, wipe in straight lines from the centre of the disc to its edge. Never wipe in circular motions.
• When removing a disc from its storage case, press down on the centre of the case and lift the disc out, holding it carefully by its edges.
• Fingerprints and dust should be carefully wiped off the disc’s recorded side with a soft cloth. Unlike conventional records, compact discs have no grooves to collect dust, so gently wiping with a piece of soft cloth should remove most particles.

Cassette Operation

• This product plays tapes in the format Compact Cassette. This product does not support other rape formats.
• When playing home recorded cassettes the playback quality might be infiuenced by the quality of the recording equipment and of the blank cassette used.

Inserting and Removing a Cassette

• Press the FUNCTION button to select ‘TAPE’ mode. The LCD will show TAPE’
• Open the cassette compartment by pressing STOP/EJECT button.
• Insert a cassette, then close the cassette compartment.

Cassette Playback

• Press the PLAY button to start playback. The product resumes playback from where it has stopped at after the last playback
• Press the PAUSE button to pause playback and press it again to resume playback.
• During playback, use the FE.F.WD and RWD buttons to fastforward and rewind the tapes. Stop the winding by pressing the STOP/EJECT button once.
• When playback reaches the end of the tape, the PLAY butoon pops up.
• To manually stop playback. press the STOP/EJECT button.

Recoding on a tape
NOTE: Be sure to connect the AC power cord to avoid an unexpected recording failure.

1. Press POWERbutton tum on the power of the unit, and then prepare the source you want to record.
   To record CD tracks ona disc

   • Place a disc in the CD compartment. Make sure not to start playback. See Playing a Disc.”  To record a FM radio program
   • Tune to the desired station. See “FM Radio Operation.”

2. Press STOP/EJECT button, insert a cassete tape into the cassette tape compartment and then close the compartment cover.

3. Press RECORD button to start recording (the PLAY button will depress automatically at the same time).

   • When recording from a disc Playback starts automatically and recording of all the tracks on the disc proceeds from the first track. When the tape reaches the end, recording stops automatically. When recording a FM1 dio program
   • Recording continues until the tape reaches the end.
     NOTE: Adjusting the olume will not affect the recording level.

4.  Stop recodring by press STOP/EJECT button

5. Pause recroding by press PLAY button, to resume recording, press the button again.

6. Connecting Headphones
   CAUTION: Do not wear the earphones immediately without lowering the volume first.
   NOTE: When the headphotes/earphones are connected, the main speakers are muted automatically

   • Rotate the VOLUME knob anticlockwise to the lowest volume.
   • Connect the headphones to the 3.5mm headphone socket.
   • Adjust the volume by rotating the VOLUME knob..

CARE AND MAINTENANCE

Care of the product & Caution

• To prevent fire or shock hazard your unit from the AC power source. Disconnect the product from the power source when cleaning.
• If the unit becomes dusty, wipe it with a soft and dry cloth to clean this product. Do not use any wax, polish sprays, or abrasive cleaners on the unit.
• Never allow any water or other liquids to get inside the unit while cleaning. Dispose of used batteries in an environmental-responsible manner. This product is not intended for commercial use. Household uses only..

TOUBLE SHOOTING

TECHNICAL SPECIFICATION

Power supply

• Operation voltage: AC 230V-, 50Hz
• Power consumption: 14 W
• Batteries: 12V =,8x 1.5V, type C/R14/UM2 batteries (not supplied)
• Speaker power: 2 x 1 W (RMS)

Radio

• Frequency band: 87.5- 108 MHz (FM)
• Antenna: telescopic antenna (FM)
• Dimensions (Wx Hx D): approx. 290 x 155 x 220mm

NOTE: As a result of continual improvements, the design and specifications of the product within may differ slightly to the unit llustrated on the packaging.

PLL Radio Operation

1. The appliance is equipped with a telescopic antenna located at the back of the appliance. Pull out the antenna completely and rotate to achieve the best FM reception.
2. Press POWER/OFF button to turn on the unit.
3.  Press the FUNCTION button to select the FM mode.

MANUAL STATION SELECTION

1.  Press the TUN-/ or TUN+/ button step by step to tune to the desired radio stations.
2. Press VOLUME + or VOLUME- button for the desired volume level. v You can also choose the desired radio station by turning the TUNING Control on the side of boombox. The selected radio frequency can be read on the LCD display.

SEARCH STATION OPERATION

1. Press and hold the TUN-/ or TUN+/ button for approx. 3 second, it will start to search the next radio station in the direction of the search.
2. The search operation simply finds stations with strong signals. Stations with weak reception can nly be tuned in manually.
3. Press VOLUME+ or vOLUME- button for the desired volume level.

MEMORIZE RADIO STATIONS

1.  Tune to the desired station.
2. Long press PROG. button, the LCD display will show ‘PO1’.
3.  Press TUN-/ or TUN+/ button and select the desired number of your program.
4.  Press PROG. button to store the radio station in the memory.
5. Repeat steps from 1 to 3 to store more tracks in memory. You can store up to 20 radio stations in the memory.

TO SELECT THE RADIO STATION IN THE MEMORY
Short press PROG. button for the radio station memory and press PRO6. button skip up to the next memory station.
NOTE: As a result of continual improvements, the design and specifications of the product within may differ slightly to the unit illustrated on this file

1. Press the POWER button turn on the power of the unit and prepare the BLANK tape for recording.
2. Press STOP/EJECT button to open the Cassette Door, insert a cassette tape, and close the Cassette Door.
3. Press FUNCTION button switch to one of the other settings (FM/CD).
4. While playing from the Source, press RECORD button (PLAY button will depress automatically at the same time). Audio from the Source will be copied to the tape.
5. Recording continues until the tape reaches the end. Or stop recording by press STOP/EJECT button.
   NOTE: Adjusting the volume will not affect the recording level.
   NOTE: Record only possible from CD or FM function

SPECIFICATIONS

WARRANTY

All products come with a standard 12 month warranty. All items must be registered on www.oakcastle.co.uk for the warranty to be valid. Once on the web page, use the menu to find “register your product”. You will also be given the chance to extend your warranty for an additional 24 months, free of charge.

1. Read these instructions.
2. Keepthese instructions. Instructions are also avail able for download at www.oakcastle.co.uk
3. Heed all Warnings
4. Follow all instructions
5. Do not clean the apparatus near or with water
6. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions
7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
8. Protect the power from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
9. Only use attachments/accessories specified by the manufacturer.
10. Unplug this apparatus during light storms or when unused for long periods of time.
11. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in a way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to the rain or moisture, does not operate normally or has been dropped.
12. No naked flame sources, such as lit candles, should be placed on the apparatus.
13. Dispose of used electrical products and batteries safely according to your local authority and regulations.

ADDITIONAL WARNINGS
The apparatus shall not be exposed to dripping or splashing and no objects filled with liquid, such as vases, shal be places on the apparatus. Main plug is used to disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the main mains completely, the mains plug should be disconnected from the main socket outlet completely. Battery shall not be exposed to excessive heat such as sunshine, fire or the like.

RECYCLING ELECTRICAL PRODUCTS
You should now recycle your waste electrical goods and in doing so help the environment. This symbol means an electrical product should not be disposed of with normal household waste. Please ensure it is taken to a suitable facility for dispos- al when finished with.
IMPORTANT: Please read all instructions carefully before use and keep for future reference.

• A Risk of electric shock. Do not open
• Read all instructions carefully before use and keep for future reference
• When servicing, use only identical replacement parts

References

• Oakcastle | Now in over 3 Million Homes

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>