GeoVision GV-BX2802 2MP Pro Box IP Camera User Guide

GeoVision GV-BX2802 2MP Pro Box IP Camera

Product Information

Specifications

• Model: GV-BX2802, GV-BX4802
• Power: DC 12V / AC 24V
• Connectivity: Ethernet connector (PoE)
• Storage: Micro SD card slot
• Audio: Audio input, Audio output
• Video output: Yes

FAQ

• Q: What should I do if the product does not work properly?
  • A: Contact your dealer or the nearest service center for assistance. Do not attempt to disassemble the camera yourself.
• Q: Can I use a manual iris lens with this camera?
  • A: Yes, you can use a manual iris lens with the camera. In this case, you do not need to connect the power cable of the auto iris.

Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.

Warning and Caution

• If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the camera yourself. (We shall not be responsible for any problems caused by unauthorized repair or maintenance.)
• Keep away from liquid while in use.
• In the use of the product, you must be strict compliance with the electrical safety regulations of the nation and region. When the product is mounted on wall, the device shall be firmly fixed.
• Do not use camera beyond specified voltage range.
• Do not drop the camera or subject it to physical shock.
• Avoid touching the camera lens.
• If cleaning is necessary, please use clean cloth to wipe it gently.
• Do not aim the camera at the sun or extra bright place.
• Do not place the camera in extremely hot, cold, dusty or damp locations, and do not expose it to high electromagnetic radiation.
• To avoid heat accumulation, good ventilation is required for operating environment.

Overview

Note

1. The camera can be powered by DC 12V / PoE power supply. If the PoE switch is used to power the camera, DC 12V power supply is not required.
2. To load default settings, press and hold the default button for 10 seconds.

RS 485/ Alarm input/Output Cable Connection

• Use the small slotted screwdriver to press the corresponding button. Then insert the cable into the cable groove. After that, release the screwdriver.

Alarm Input:

Alarm Output:

Installation

Please make sure that the wall or ceiling is strong enough to withstand 3 times the weight of the camera. Install the camera under dry environment. Here we take

1. Insert a micro SD card into the card slot.
2. Remove the protection cover of the lens interface and install the lens (not supplied) to the camera. Rotate the lens clockwise until it is fixed firmly. Plug the cable of auto iris to the auto iris interface of the camera.

Note: It is not required to plug the power cable of the auto iris to the auto iris interface if a manual iris lens is used.

Accessing the Network Camera

Looking Up the Dynamic IP Address

• By default, when the camera is connected to a LAN with the DHCP server, it is automatically assigned with a dynamic IP address. Follow the steps below to look up its IP address.

Note

• By default, the Administrator’s username is admin and cannot be modified.
• This function is only applicable on GV-IP Device Utility V8.9.8 or later.

1. Make sure the PC used to configure the IP address is under the same LAN as the camera. Download and install GV-IP Device Utility from the company website.
2. On the GV-IP Utility window, click the button to search for the IP devices connected in the same LAN. Click the Name or Mac Address column to sort.
3. Find the camera with its Mac Address, and click on its IP address.
4. For the first-time users, you are requested to set up a password.
5. Type a new password and click OK.
6. Click on its IP address again and select Webpage to open its Web interface.
7. Type the set password on the login page and click Login.

IMPORTANT:

1. The camera has two sets of passwords: one is for Web interface and the other is for the third-party platform connection via ONVIF, e.g. GV-VMS. GV-IP Device Utility is used to set the ONVIF password. When the first-time user uses GV-IP Device Utility to set a password for the camera, the two sets of passwords are created simultaneously.
2. To change the password for Web interface, click Config → Security → User ; see “Modify User” in 4.7.1 Security Configuration in the user’s manual. To change the password for ONVIF connection, click Config → Network → Advnaced; see 4.6.4 ONVIF in the user’s manual.
3. If the first-time user accesses the camera’s Web interface on the browser directly by using the IP address found in GV-IP Device Utility, the following dialog box will apear.

If “Activate Onvif User” is enabled, the ONVIF user can be activated simultanously for the third-party platform connection via ONVIF, using the default username and set password set above to connect.

Configuring the IP Address

If the camera is connected to a LAN without the DHCP server, the default IP address will be 192.168.0.10. Follow the steps below to modify the IP address to avoid IP conflict with other GV-IP devices on the same LAN.

1. Open your Web browser, and type the default IP address 192.168.0.10.
2. Type the default username admin and a password. Click Login.
3. Go to Config > Network > TCP/IP to set the IP address.
4. Select Use the following IP address and then enter the static IP address and other parameters.

The Web Interface

Once you log in the Web interface, you will see the live view as shown below.

For detailed information, see the user’s manual.

Upgrading System Firmware

GeoVision periodically releases updated firmware on the company website. To load the new firmware into the camera, follow the instructions below.

1. On the Web interface, click Config > Maintenance > Upgrade.
2. Click the Browse button to locate the firmware file saved at your local computer.
3. Click the Upgrade button to start upgrading the firmware.
4. After upgrading, the camera will restart automatically.

Note: Do not close the browser or disconnect the camera from the network during the upgrade.

Restoring to Factory Default

If for any reason the camera is not responding correctly, you can restore the camera back to its factory default settings using the Web interface or the Load Default Button.

On the Camera

1. Find the Load Default button on the camera (see No. 11, 1. Overview in the Quick Start Guide).
2. Press and hold the button for more than 10 seconds to restore to the factory default setting.

On the Web Interface

1. On the Web interface, click Config >Maintenance > Backup & Restore.
2. Click the Load Default button to restore all system settings to factory default, except the image settings (see 4.2 Image Configuration in the User’s Manual for details) you want to keep.

© 2022 GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of GeoVision.

Every effort has been made to ensure that the information in this manual is accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind and assumes no responsibility for errors or omissions. No liability is assumed for incidental or consequential damages arising from the use of the information or products contained herein. Features and specifications are subject to change without notice.

GeoVision, Inc.

• 9F, No. 246, Sec. 1, Neihu Rd., Neihu District, Taipei, Taiwan
• Tel: +886-2-8797-8377
• Fax: +886-2-8797-8335
• http://www.geovision.com.tw

Trademarks used in this manual: GeoVision, the GeoVision logo and GV series products are trademarks of GeoVision, Inc. Windows is the registered trademark of Microsoft Corporation.

August 2022

Scan the following QR codes for product warranty and technical support policy:

Documents / Resources

| GeoVision GV-BX2802 2MP Pro Box IP Camera [pdf] User Guide
GV-BX2802, BX4802, GV-BX2802 2MP Pro Box IP Camera, 2MP Pro Box IP Camera, Box IP Camera, IP Camera, Camera
---|---

References

• Download - GeoVision
• Geovision GV-BX2802 2MP Pro Box IP Camera

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>