GeoVision GV-RK1355 RS-485/Wiegnd Proximity Reader User Guide
- June 3, 2024
- GeoVision
Table of Contents
GeoVision GV-RK1355 RS-485/Wiegnd Proximity Reader User Guide
Package Contents
Kindly ensure the product’s contents upon unpacking; please refer to this quick start guide regarding the product ‘s specifications and important notices.
Reader x 1 Basex 1
Quick Start Guide x 1
Screw X 3
Physical Dimension
Installation
-
Kindly refer to the “ 4 wiring connection” for the NODE ID settings before the hardware installation.
Do not over tighten the back base screws during installation to prevent distortion.- (A). Mount the back base onto the wall or electrical back box .
- (B). Connect the wires in accordance with the wiring instruction below.
- (C). Make sure the back base and the reader upper cover guides are aligned.
- (D). Install the reader upper cover to the back base.
- (E). Fasten the screw onto the bottom of the reader.
Wiring Connections
Before mounting the reader onto desired location. Please set the NODE ID (DIP
Switch, binary number system).
The position of the components varies according to the reader’s model. Kindly
take note of the components during setup.
- A. NODE ID Settings, refer to the chart below.
- NODE ID Setting
Node ID| Node ID
---|---
0| 000000
1| 100000
2| 010000
3| 110000
4| 001000
5| 101000
6| 011000
7| 111000
8| 000100
9| 100100
10| 010100
11| 110100
12| 001100
13| 101100
14| 011100
15| 111100
- NODE ID Setting
ON=1, OFF=0
* Dip(6) is card format selection. ON is for reading the document, and OFF is for reading the serial number.
- B.
PIN| Color| Wiegand| RS-485
---|---|---|---
1| Red| DC +12V IN| DC +12V IN
2| Black| Ground| Ground
3| Yellow| –| RS-485+
4| Blue| –| RS-485-
5| Purple| Beep Control|
6| Brown| Green LED Contro|
7| Green| –|
8| White| –|
9| Light blue| W0|
10| Gray| W1|
Note:
- Kindly use minimum 22AWG double-shielded aluminum mylar foil twisted pair cable for the connection between the reader and the controller.
- In order to reduce long distance noise,The isolated net of transmission cable should connect to both ends of device ground.
- The distance between two readers should be over 30cm to prevent radio frequency interference from each other.
- Mounting the device around metal could affect read range. Metal of any type around the device should be avoided while mounting.
- The distance between the reader and the controller should not exceed 30 meters.(For wiegand/T2 modle only)
- For optimum read range, kindly use DC Linear power adaptor for the reader’s power supply.
- In order to ensure the reader’s normal operation, input voltage should be between 12V±10%.
- RS-485 communication Baud rate is 9600.
Testing
To avoid interference self-detection of sensitive touch keypad, please do not touch the keypad when input power.
When the power is on, the reader’s red LED and the reader will beep
concurrently
Place the card provided near the reader.
The reader will beep concurrently.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, any changes or modifications
not expressly approved by the party responsible for compliance could void the
user’s authority to operate this equipment.
(Example – use only shielded interface cables when connecting to computer or
peripheral devices)
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
One Year Limited Warranty
We warrants this product against defect in material or workmanship for 1 year
from the date of purchase. If such a defect is discovered within this warranty
limitation, contact your direct vendor for repair or replacement of your unit.
When returning the product, you must ship the product in its original
packaging or packaging that gives an equal degree of protection. This warranty
becomes invalid if the factory-supplied serial number has been removed or
altered on the product.
This warranty does not cover cosmetic damage or damage due to acts of God,
accident, misuse, abuse, negligence or modification of any part of the
product. This warranty does not cover damage due to improper operation or
maintenance, connection to improper equipment, or attempted repair by anyone
other than We.
In no event shall We liability exceed the price paid for the product from
direct, indirect, special, incidental, or consequential, damages resulting
from the use of the product the product, its accompanying software, or it’s
documentation. We makes no warranty or representation expressed, implied, or
statutory, with respect to its products, contents of use of this documentation
and all accompanying software, and specially disclaims its quality ,
performance, merchantability or fitness for any particular purpose. We
reserves the right to revise or update its product, software or documentation
without obligation to notify any individual or entity
Model
Serial no.
Date of Purchase
Reseller stamp
Warranty will be valid only after filling out this form and stamped or signed by reseller!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>