GeoVision 3DPCV2-QG-C GV-3D People Counter V2 Projector User Guide

GeoVision 3DPCV2-QG-C GV-3D People Counter V2 Projector

Specifications

• Product: GV-3D People Counter V2
• Manufacturer: GeoVision, Inc.
• Address: 9F, No. 246, Sec. 1, Neihu Rd., Neihu District, Taipei, Taiwan
• Contact: Tel: +886-2-8797-8377,
• Fax: +886-2-8797-8335,
• Website: www.geovision.com.tw
• Trademark: GeoVision, GV series products

Introduction

Welcome to the GV-3D People Counter V2 Quick Start Guide. In the following sections, you will learn about the basic installations and configurations of the GV-3D People Counter V2. For the detailed user’s manual, see GV-3D People Counter V2 User’s Manual.

Packing List

Overview

Bottom and Rear Views

Terminal Block
The 8-pin terminal block, located on the rear panel, provides interfaces for connecting a digital input, a relay output and a GV-GPS Receiver.

Connection

The instructions below describe the basic connection required to operate GV-3D People Counter V2.

1. Plug a standard network cable or PoE to provide a power supply and Internet connection.
2. Insert a micro SD card.

Note: GV-3D People Counter V2 only supports PoE. You may purchase a GV- PA191 PoE adapter to connect to your router. See 1.2 Optional Accessories.

Wall / Ceiling Mount

You can use the Wall / Ceiling Mount Kit to mount GV-3D People Counter V2 on a desired location.

1. Remove the device’s outer case.
2. Secure the desired mounting kit to the designated position with 2 screws.
3. Reassemble the outer case.
4. Put the installation sticker to the wall with the arrow pointing up.
5. Drill 2 holes according to the sticker and insert the 2 screw anchors to the 2 holes.
6. Secure the device to the wall with 2 long screws.
7. Optionally install the ground wire with the screw as shown below:

Accessing the Web Interface

Once the GV-3D People Counter V2 is connected to the network, you can view counting data by using its built-in Web interface, GV-Web Report Lite. When the device is connected to a network with a DHCP server, it will be automatically assigned a dynamic IP address. To look up this IP address, use GV-IP Device Utility described in Chapter 4 GV-IP Device Utility in GV-3D People Counter User’s Manual.
However, if you do not have a DHCP server on your network, access the device by its default IP address 192.168.0.10.

System Requirements
To access the device, Microsoft Internet Explorer 10 or above is required.

Logging In

1. In your Web browser, type the IP address or the domain name of the device in the Location / Address field. This page appears.
2. Select the Language.
3. Type the default ID and password admin.
4. Type the characters shown in the image and click Login. The Counting Signage page appears, which will display real-time counting data after you set up the device.
5. Click Setup on the top left corner to set up the device.

Setting the GV-3D People Counter V2
To set the GV-3D People Counter V2, click the Setup tab on the top. The Setup page appears.

[Detection Mode] Choose the desired detection mode from People Counting or Dwell Time.

• People Counting: Counting and recording the number of people entering and leaving a designated area based on the directions set.
• Dwell Time: Record the dwell time of persons staying within a designated area.

[Live View] Draw a box on the live view to mark the boundary of the detection zone.

• For People Counting, people moving across the blue box in the direction of the red and green arrows will be respectively counted as Out and In.

• For Dwell Time, a timer is set on every person entering the designated area, which only stops and records the dwell time upon the person leaving the area.

Note:

1. People Counting and Dwell Time cannot function simultaneously.
2. For Dwell Time, make sure enough space is left outside the edges of the designated area for determining the detected persons to be fully out of the area upon leaving.
3. Device Height: Type the height of the installed device. Depending on the height where the device is installed, the range of detectable height for people varies.
4. Minimum People Height: Type the minimum height for a person to be detected.
5. Device and Object Distance < 60 cm: Select this option when the distance of the installed device and intended objects is lower than 60 cm. Once the option is selected, the detection range will be reflected below.
6. Detail: Click the button to see an illustration of the detectable range and the dimensions of the detection area based on the height you specified.

For details, see 3.2 Setting the GV-3D People Counter V2 in the GV-3D People Counter V2 User’s Manual.
Note: GV-3D People Counter V2 is only compatible with GV-Web Report V3.0.0.0 or later.

Accessing Counting Results
After the GV-3D People Counter V2 is properly configured and the data collection process begins, you can access the following pages for the people counting data in the format of tables, graphs and charts:

• Device: Displays the real-time counting data in tables and bar charts from all connected devices. The data is updated every minute.
• Group: Allows you to organize the connected GV-3D People Counter V2 into Groups and view the data of created groups.
• Log: Allows you to view the data of a specified period from the selected GV-3D People Counter V2.
• Query: Provides counting data on the daily, weekly, monthly, and yearly graphs and tables.

Note:

1. When detection mode is set as Dwell Time, only the persons entering the designated area are counted and displayed as In.
2. When the detection mode is set as Dwell Time, Log and Query functions are not supported.

For details, see 3.2 Setting the GV-3D People Counter V2 in the GV-3D People Counter V2 User’s Manual.

Upgrading the Firmware

We will periodically release the updated firmware on the website. You can update firmware by using GV-Web Report Lite.

1. Download the latest firmware to your computer.
2. Log onto the GV-Web Report Lite and click Setup on the upper right.
3. Select the FW tab.
4. In t he Upload File field, click Open to select the firmware file.
5. Click Apply to begin updating firmware. The device will restart after the firmware upgrade is complete.

FAQ

• Q: How do I reset the GV-3D People Counter V2 to factory  settings?
  • A: To reset to factory settings, press and hold the Default Button for 10 seconds until the status LED blinks rapidly.
• Q: What is the recommended operating temperature for the product?
  • A: The recommended operating temperature range is between 0°C to 40°C.

© 2021 GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind and assumes no responsibility for errors or omissions. No liability is assumed for incidental or consequential damages arising from the use of the information or products contained herein. Features and specifications are subject to change without notice.

GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: +886-2-8797-8377
Fax: +886-2-8797-8335
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV series products are trademarks of GeoVision, Inc. Windows is the registered trademark of Microsoft Corporation.
October 2021

Scan the following QR codes for product warranty and technical support policy:

References

• Geovision GV-3D People Counter V2

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>