GeoVision GV-AS EV Controller User Guide
- June 3, 2024
- GeoVision
Table of Contents
GeoVision GV-AS EV Controller
Thank you for purchasing GV-AS / EV Controller. This guide is designed to assist the new user in getting immediate results from the controllers. For advanced information on how to use the controllers, please refer to GV-AS / EV Controller User’s Manual on the software CD / DVD.
2021 GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part,
without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is
accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind
and assumes no responsibility for errors or omissions. No liability is assumed
for incidental or consequential damages arising from the use of the
information or products contained herein. Features and specifications are
subject to change without notice.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: +886-2-8797-8377
Fax: +886-2-8797-8335
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV series
products are trademarks of GeoVision, Inc. Windows is the registered trademark
of Microsoft Corporation.
October 2021
Scan the following QR codes for product warranty and technical support policy:
Preface
Welcome to the GV-AS / EV Controller Quick Start Guide.
This Quick Start Guide is designed for the following models:
| Model | Model Number |
|---|
GV-AS Controller
| GV-AS100 / 1010
GV-AS110 / 1110
GV-AS120
GV-AS210 / 2110 / 2120 / 2121
GV-AS410 / 4110
GV-AS810 / 8110
GV-EV Controller| GV-EV48
Separate manuals have been produced for other model numbers of GV-Controllers
not listed above. Visit
www.geovision.com.tw/download/product/
to search for specific model numbers
and download their technical documentation.
Important Note for Maintaining Power Supply
To make sure GV-AS / EV Controllers can function properly during a power
outage, be sure to replace the internal battery on the controllers when
needed. It is also recommended to install a backup battery for compatible GV-
AS Controllers.
Refer to the following sections in GV-AS Controller User Manual for instructions on how to install a backup battery:
- GV-AS100 / 110 / 120 through GV-ASBox: See 9.1.4.F Connecting Backup Battery.
- GV-AS100 / 110 / 120 through GV-ASNet: See 9.2.4.F Connecting Backup Battery.
- GV-AS210 / 2110 / 2120: See 4.2.4 Connecting Backup Battery
- GV-AS410 / 4110 / 810 / 8110: See 5.2.4 Connecting Backup Battery
- GV-EV48: See 6.2.3 Connecting Backup Battery.
Replaceable Button Cell (GV-AS100 / 2110 / 2120 / 4110 / 8110)
For GV-AS100 / 2110 / 2120 / 4110 / 8110, you can replace the battery on your
own when you see low battery messages and icons in GV-ASManager.
Note: Make sure the plastic insulation film under the battery is removed when using GVAS100 / 2110 / 2120 / 4110 / 8110 for the first time. The low battery messages and icons will appear if the plastic film is not removed.
Built-in Battery (GV-AS1010 / 110 / 1110 / 120 / 210 / 410 / 810 & GV-EV48) When the controller runs out of battery, the local time on the controller will be reverted back to 1999/12/31. The controller time can be found on the Web interface of the controller on the Time Setting page and in the Access Monitor / Alarm Monitor / Event Monitor of GVASManager.
When you see the controller year shown as 1999 or 2000, disconnect the controller from power and reconnect it to power. If the year is still shown as 1999 or 2000, the controller battery needs to be replaced. When this occurs, connect the controller to a backup battery and maintain connection with GV- ASManager at all times. When connected to GVASManager, the controller’s time will be synchronized with GV-ASManager’s time.
GV-AS Controller Quick Start Guide
This guide lists the basic steps required to set up a GV-AS Controller. For
detailed instructions, refer to the section number listed below each step.
Basic Setup for GV-AS100 / 1010 / 110 / 1110 / 120
This section covers the basic settings required to start running GV-AS100 /
1010 / 110 / 1110 / 120. For more settings on GV-AS100 / 110 / 120, refer to
5. Optional Devices for GV-AS100 / 110 / 120. The section numbers listed here
refers to the GV-AS Controller User Manual.
GV-AS100 / 1010
GV-AS110 / 1110
GV-AS120
Physical Wiring for GV-AS210 / 2110 / 2120 / 410 / 4110 /810 / 8110 and GV- EV48
GV-AS210 / 2110 / 2120
GV-AS410 / 4110 / 810 / 8110
GV-EV48
Accessing the Web Interface of the GV-AS Controllers
After connecting the required wires and cables for the following GV-AS
Controllers, access the Web interface of the GV-AS Controller to define the
devices connected: GV-AS1010 /
1110 / 210 / 2110 / 2120 / 410 / 4110 / 810 / 8110 and GV-EV48. The section
numbers listed here refers to the GV-AS Controller User Manual.
Setting GV-AS Controller on GV-ASManager
After setting up the Web interface, connect the GV-AS Controller to a GV-
ASManager.
Through GV-ASManager, you can set up the doors and enroll cards. The section
numbers listed here refers to the GV-ASManager User Manual.
Optional Devices for GV-AS100 / 110 / 120
To access GV-AS100 / 110 / 120 on a network, an optional device GV-ASBox or
GV-ASNet is required. GV-ASBox also supports connection with additional input
devices, output devices
and readers through Wiegand interface and RS-485 interface. GV-ASNet supports
additional readers through RS-485 connection.
You will need to first complete the physical wiring of GV-ASBox or GV-ASNet
before accessing the Web interface. After the controller is installed on a
network, GV-AS100 / 110 / 120 can also connect with GV-ASManager for advanced
settings. Refer to 4. Setting GV-AS Controller on GV-ASManager for details.
Physical Wiring of GV-ASBox and GV-ASNet
The section numbers listed here refers to the GV-AS Controller User Manual.
Accessing the Web Interface of GV-AS100 / 110 / 120
The section numbers listed here refers to the GV-AS Controller User Manual.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>