anko SLR-23006 Lava Lamp Instruction Manual
- May 15, 2024
- Anko
Table of Contents
- anko SLR-23006 Lava Lamp
- IMPORTANT SAFETY INSTRUCTIONS:
- ADDITIONAL SAFETY PRECAUTIONS FOR LIGHTING:
- BULB REPLACEMENTS INSTRUCTIONS:
- Product specification
- INSTRUCTIONS FOR INSTALLATION:
- Troubleshooting
- 12 Month Warranty
- Frequently Asked Questions (FAQ):
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
anko SLR-23006 Lava Lamp
INSTRUCTION MANUAL
Lava Lamp Red
K: 43351589 T: 68734961
SLR-23006
IMPORTANT SAFETY INSTRUCTIONS:
The following safety precautions should always be followed, to reduce the risk of electric shock, personal injury or fire. It is important to read all of these instructions carefully before using the product, and to save them for future reference or new users.
1. This product must only be used as intended in accordance with the enclosed
operating instructions.
2. Do not carry the appliance by the mains cable or pull the cable to remove
the plug from the socket.
3. If the external flexible cable or cord of this luminaire is damaged, it
shall be exclusively replaced by the manufacturer or his service agent or a
similar qualified person in order to avoid a hazard.
4. If the appliance stops unexpectedly or appears to malfunction, switch off
the power supply, unplug from the mains and stop using immediately. Seek
professional advice to rectify the fault or make repairs.
5. Switch off the power supply and unplug from the mains socket when not in
use, before cleaning or changing accessories.
6. Avoid positioning the appliance where the power cable might be
accidentally trapped or damaged.
7. Keep the appliance and cable away from sources of heat, sharp objects or
anything that may cause damage.
8. Ensure the appliance is switched OFF before connecting the mains power
supply.
9. Be aware that some surfaces may become hot. Do not touch hot surfaces and
supervise others accordingly.
10. This product has not been designed for use by children.
11. Children should be closely supervised at all times when they are near any
electrical appliance.
12. To protect against electric shock, never allow the appliance, the mains
cable or plug to come into contact with water or any other liquid.
13. Never reach for any appliance that has fallen into water. Switch off the
power supply at the mains immediately and unplug. Do not re-use until the
product has been inspected and approved by a qualified electrician.
14. Always ensure that hands are dry before operating or adjusting any switch
on the product or touching the plug and mains supply connections.
15. To disconnect, first ensure that all controls are in the OFF position,
then remove the plug from the electricity supply.
16. Where relevant keep all ventilation slots, filters, etc. uncovered and
clear of debris. Never drop or insert objects into the openings.
17. Do not use outdoors. This appliance has been designed for domestic indoor
use only.
ADDITIONAL SAFETY PRECAUTIONS FOR LIGHTING:
1. DO NOT REMOVE BOTTLE CAP FROM GLASS GLOBE. Do not remove the cap on the
globe or add anything to the globe. The air space at the top of the globe is
necessary in order to allow for the expansion of contents. Breaking the seal
on the globe shall void the warranty.
2. Remove all excess packaging before assembling.
3. Check and see if the lampholder in the lava lamp base are centered. The
socket may have moved during shipping. If this has occurred, then gently use
your fingers to re-center it.
4. Only use provided bulb. Variances in bulb size or wattage will produce
unsatisfactory operation, fire, or possible breakage of the globe.
5. Run the lamp on a clean and flat surface, away from heated surfaces and
direct sunlight. Direct sunlight may cause colors to fade.
6. Allow the lamps to warm up for 1 hour and 45 minutes to 2 hours to ensure
it performs at its optimal level. Note: All lava lamp have a coil
in the bottom of the globe. This is to accelerate the heating process.
7. Suggest not to continuously operate more than 10 hours.
8. Exercise caution when handling the lamp while it is plugged in. The lamp
will take 2 to 3 hours to cool after it has been turned off.
9. To disconnect, turn all controls to the off position, then remove plug
from outlet.
10. Do not place the lamp near sources of heat or cold, such as a heater or
air conditioner. The lamp operates best at 20-25 º C room temperature.
11. Handle product with care; the glass globe may break if subjected to any
form of sudden impact. If it becomes necessary to clean up broken glass first
unplug unit and then use care and safety precautions. (Refer to Clean-Up
Instructions below for details.)
12. Do not use any other means to heat up motion lamp besides bulb provided
nor attempt to cool it down artificially.
13. Do not shake the lamp while the product is warm. Lamp will become cloudy
and unable to repair.
14. Do not operate the lamp on glass surfaces, where aerosol spray is being
used, or where oxygen is being administered.
15. If in doubt, consult a qualified electrician.
CLEAN UP INSTRUCTIONS FOR ACCIDENTAL BREAKAGE: If the globe breaks, it is not harmful if it is handled properly. KMART PTY LTD IS NOT RESPONSIBLE FOR DAMAGE CAUSED BY PRODUCT BREAKAGE.:
1. Wear rubber gloves during the clean-up process in order to protect skin
irritation and to prevent cuts from broken glass.
2. Carefully pick up and dispose of broken glass and plastic pieces.
3. Use disposable towels to soak up excess liquid (you can use water to aid
in clean up because the liquid is water soluble).
4. Thoroughly clean any products soiled by the liquid.
5. After the liquid has been cleaned up, a commercial cleaning detergent may
be used to deep clean the area. Prompt clean-up is key.
6. For carpet, blot up spilled material with an absorbent disposable cloth.
Follow cleaning directions from your carpet manufacturer.
7. For floors, wipe up with disposable cloth and clean with normal floor
cleaning detergent.
BULB REPLACEMENTS INSTRUCTIONS:
Before attempting to change the light bulb, please follow the below instructions carefully:
1. Turn off and unplug the lamp from the outlet.
2. Please wait at least one hour, then remove the glass globe from the base.
Set aside in a safe location.
3. Please wait at least one hour for the bulb to cool down before replacing.
Do not attempt to remove light bulb while hot.
4. Once light bulb is cool to the touch, carefully unscrew from base and
discard safely.
5. Replace with the new light bulb by screwing into the base socket. Please
see specifications below for correct bulb wattage.
6. Replace glass globe, plug into outlet, and turn your lamp on.
Product specification
- Rated voltage: 220-240V ~ 50Hz
- This lamp requires: 1 x 30W E14 Small Edison Screw incandescent R39 bulb (bulb included)
INSTRUCTIONS FOR INSTALLATION:
1. Caution: Assemble the lamp completely before connecting to the electricity
supply.
2. Remove all excess packaging before installation.
3. Install the bulb – 30W R39 E14 Small Edison Screw (provided) into the
lampholder.
4. Put the glass bottle on the base as instructions.
5. Cover the metal cap on the bottle.
6. Check to ensure that all the components have been assembled correctly.
7. Connect to the mains supply.
ADDENDEM: WHEN USED FOR THE FIRST TIME, THE COLOUR OF THE WAX MAY BE CLEAR. IT WILL BE TURNED TO A SOLID COLOUR AFTER REPEAT USE.
Troubleshooting
Problem | Possible reason | Solution |
---|---|---|
Unit does not work | Connection problem | Check to ensure that all the |
components have been assembled correctly.
Wax does not melt or could not melt well.| Temperature is low.| Check the bulb
wattage is correct or not. This lamp requires 30W R39 incadescent bulb. Other
bulbs may produce unsatisfactory operation.
Ensure the room temperature should be 20-25 ℃. Low room temperature may cause
the product unsatisfactory operation. Best operation temperature is 21℃.
Allow the lamps to warm up for 1 hour and 45 minutes to 2 hours to ensure it
performs at its optimal level.
Check if there is fan or air conditioner working around the product. Air flow
may cause the product heat loss too quickly that cause the product not good
performance.
Wax float too much in the water and not come down| Temperature is too high|
Ensure the room temperature should be 20-25 ℃. High room temperature will
cause the wax not come down because the wax is too hot. The density of the wax
in hot is lower than the water.
Many bubbles in the wax when operation| Wax had been stirred before filled in
the bottle. The air entried in the wax when stirring.| After several times
operation, the bubble will be disappeared.
CAUTION: DO NOT SHAKE THE BOTTLE WHILE THE PRODUCT IS WARM. WAX WILL BECOME CLOUDY AND UNABLE TO REPAIR.
12 Month Warranty
Thank you for your purchase from Kmart.
Kmart Australia Ltd warrants your new product to be free from defects in
materials and workmanship for the period stated above, from the date of
purchase, provided that the product is used in accordance with accompanying
recommendations or instructions where provided. This warranty is in addition
to your rights under the Australian Consumer Law.
Kmart will provide you with your choice of a refund, repair or exchange (where
possible) for this product if it becomes defective within the warranty period.
Kmart will bear the reasonable expense of claiming the warranty. This warranty
will no longer apply where the defect is a result of alteration, accident,
misuse, abuse or neglect.
Please retain your receipt as proof of purchase and contact our Customer Service Centre on 1800 124 125 (Australia) or 0800 945 995 (New Zealand) or alternatively, via Customer Help at Kmart.com.au for any difficulties with your product. Warranty claims and claims for expense incurred in returning this product can be addressed to our Customer Service Centre at 690 Springvale Rd, Mulgrave Vic 3170.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
For New Zealand customers, this warranty is in addition to statutory rights observed under New Zealand legislation.
Frequently Asked Questions (FAQ):
Q: Can I use a different bulb in the lamp?
A: It is recommended to only use the provided 30W E14 bulb to ensure proper operation and safety.
Q: Can the lamp be used outdoors?
A: No, the lava lamp is designed for domestic indoor use only and should not be used outdoors.slation.