anko Low Voltage Remote Controlled 80 Cascading Tree Ball Lights Instruction Manual

Instruction Manual
LOW VOLTAGE REMOTE CONTROLLED
80 CASCADING TREE BALL LIGHTS

Low Voltage Remote Controlled 80 Cascading Tree Ball Lights

These instructions are for your safety. Please read through them thoroughly before use and retain for future reference.

Before You Start

• Decide on an appropriate location for your product (see Installation instructions below).
• If you have any doubt about installing this product, consult a qualified electrician.

Installation instructions :

1. This light is suitable for INDOOR USE ONLY.

2. The AC adaptor MUST be installed INDOORS away from weather.

3. This light set is constructed with non-replaceable bulbs.

4. Do not position or place near heaters or any other direct sources of heat.

5. This product is suitable for positioning on surfaces which have normal flammability, e.g. wood, plasterboard, masonry. However this does not include highly flammable surfaces (e.g. polystyrene, textiles).

6. Always position cables and extension leads so that they will not be a hazard to the elderly, pets and children.

7. DO NOT position this light set where it may become covered by other items e.g. curtains, nets or bedding.

8. Ensure the unit is positioned so that you have enough cable to reach an indoor mains power socket.

9. To change the light effect, simply press the button locate on top of the AC Adaptor or on the remote control 1 .COMBINATION
   2. IN WAVES
   3. SEQUENTIAL
   4. SLO-GLO
   5. CHASING / FLASH
   6. SLOW FADE
   7. TWINKLE/FLASH
   8. STEADY ON

10. Remove the tape at first, press the buttons on the remote to change the functions

A. The sensor is located in the AC adapter. AC adapter should not covered by any object.
B.Press the ‘ON/OFF” button, the light will be on or off.
C.Press the “TIMER” button, the light will be work on 6hrs, then off for 18hrs. When the Green LED on the adapter means the timer function is set.
D.Press the ‘MODE 1-2-3-4-5-6-7-8’ button, the light effect will be change
E.Press the DIM+,the light will be more brighter,press the DIM-, the light will be less dim
Adaptor :
The ratings shown on the marking is steady mode, and the input power up to 0.9W.
Adaptor other mode see below:
PRI: 220-240W 50-60Hz 0.12A }
Urated=3V-
Uout=4.5V∼ Prated Max 0.9W.

Adaptor Manual

1. Do not open the cover of the equipments.
2. The power supply is suitable for LED modules.
3. The input and output voltage should be checked before us e to ensure correct use.
4. This is the Class II product, JT-EUFC3V0.9W-H7 is only for indoor use.
5. The product is not a toy, keep it where children can not reach.
6. The lamp controlgear does not rely upon the luminaire enclosure for protection against accidental contact with live parts.
7. The adaptor is for socket mounted only. Not for Recess Use.
8. The minimum clearance distance from the top and sides o f the controlgear to normally flammable building elements is 225 mm and 300 mm.
9. The minimum clearance distance from the top and sides of the controlgerar to normally flammable building elements.
10. If the minimum clearance distances from each side of the controlgear are different, or there are different minimum clearance distances for various types of normally flammable building element or building insulation, then each minimum clearance distance shall be stated separately.
11. Where controlgear is required to be mounted on a specific surface or has additional installation requirements, for example, use in non-combustible enclosed space or to ensure adequate sealing to maintain its IP rating, the relevant infor mation shall be supplied with the controlgear.

NOTE Installation in a non-combustible enclosed space may include installation in a rebate in a concrete slab, ceiling or wall.
Diagram:

Warning

• This light is suitable for INDOOR ONLY.
• The AC adaptor MUST be installed INDOORS away from weather.
• This product is NOT designed for permanent or long term use.
• The supplied adaptor is suitable for operation of LED Modules only.
• Only operate this light set with the supplied adaptor, Model No.:JT-EL/FC3V0.9W-H7
• Do not connect this light electrically to another light.
• Do not connect this light to the power supply while it is in the packaging.
• DO NOT attempt to replace the non-replaceable bulbs in this light.
• Never allow any part of the light set to come into contact with a source of heat or flame
• Care must be taken to avoid damage the cable or fittings.
• If any part of light set or cable is damaged, the light set MUST be discarded.
• This product is for use as a decoration only. Not to be used by children as a toy. Keep out of reach of children.
• Do not position this light where it will be exposed to extreme wet weather or submerged in water.
• Always switch off this light set or unplug an adaptor if unattended.
• DO NOT overload power sockets or extension leads.
• DO NOT pierce the cable when securing in place, as this will damage the bulbs or wiring.
• Please refer to the packing or product rating label for product class, specifications and rating.

Wireless Remote controller

• Batteries installation by an adult is required.
• Insert batteries with the correct polarity.
• NEVER MIX DIFFERENT TYPES OR OLD AND NEW BATTERIES.
• DO NOT SHORT CIRCUIT SUPPLY TERMINALS OR DISPOSE OF BATTERIES IN FIRE.
• REMOVE BATTERIES DURING LONG PERIOD OF NON-USE.

LED Bulbs

This light set is constructed with non-replaceable bulbs. DO NOT attempt to replace any of the bulbs in the light set.

Keycode:42778707

Documents / Resources

| anko Low Voltage Remote Controlled 80 Cascading Tree Ball Lights [pdf] Instruction Manual
Low Voltage Remote Controlled 80 Cascading Tree Ball Lights, Remote Controlled 80 Cascading Tree Ball Lights, 80 Cascading Tree Ball Lights, Tree Ball Lights, Ball Lights
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>