Scolmore Deco Wiring Accessories 13A Socket Outlets Instructions
- June 10, 2024
- Scolmore
Table of Contents
Scolmore Deco Wiring Accessories 13A Socket Outlets
Product Information
The product is a wiring accessory, specifically a 13A socket outlet. It has a voltage rating of 250V~ and a frequency of 50Hz. The terminal size of the socket outlet is suitable for cables with a size of 4 x 2.5mm2 or 2 x 4mm2. The back box depth required for installation varies depending on the type of accessory plate used. The operational temperature range of the product is -50 to +45°C. The product conforms to The Low Voltage Directive 2014/35/EC and BS 1363-2 standards.
Technical Information
- Voltage: 250V~
- Frequency: 50Hz
- Current Rating: 13A
- Terminal Size: suitable for cables with a size of 4 x 2.5mm2 or 2 x 4mm2
- Torque Value: 2.0Nm
- Back Box Depth (Min): 25mm (Deco, Deco+, Mode, Polar, Part M, Curva), 35mm (Define, Definity)
- Operational Temperature: -50 to +45°C
- Standards: The Low Voltage Directive 2014/35/EC and BS 1363-2
Safety Information
Please read the following safety information carefully before commencing installation. This range is not suitable for outdoor installation or in areas of high humidity. Decorative accessory plates are not suitable to be mounted onto wet/damp plaster or paint, as this may cause the accessory to tarnish. For cleaning/polishing products, use only a soft, dry, clean cloth.
Product Usage Instructions
- Make the necessary mains wiring connections using the following color codes:
- `L’ – Live Coloured Brown or Red
- `CPC’ – Coloured Green/Yellow
- `N’ – Neutral Coloured Blue or Black
- After making the connections, screw the socket outlet gently to the back box ensuring no wires become trapped.
- Screw the accessory fully home making sure, when done, the plate is not distorted.
- After making the connections, screw the socket outlet gently to the back box ensuring no wires become trapped.
- Screw the accessory fully home making sure, when done, the plate is not distorted.
Mains Wiring
NOTE
- This range is not suitable for outdoor installation or in areas of high humidity.
- Decorative accessory plates are not suitable to be mounted onto wet/damp plaster or paint, as this may cause the accessory to tarnish.
- For cleaning/polishing of products, use only a soft, dry, clean cloth.
Technical Information
| Voltage | 250V~ 50Hz |
|---|---|
| Current Rating | 13A |
| Terminal Size | 5mm ø |
| Torque Value | Terminal Screw: 2.0Nm |
| Cable Size | 4 x 2.5mm2, 2 x 4mm2 |
| Back Box Depth (Min) | 25mm (Deco, Deco+, Mode, Polar, Part M, Curva) 35mm |
(Define, Definity)
Operational Temperature| -50 to +450C
Standards| The Low Voltage Directive 2014/35/EC Statutory Instruments 2014/35
BS 1363-2
Wiring Accessories – 13A Socket Outlets
Safety, Installation, and Technical Information
Safety Information
- Please read the following information carefully before commencing installation.
- Before commencing any electrical work, to prevent the possibility of receiving an electric shock, ensure the mains isolator on the consumer unit is in the ‘OFF’ position and safely isolated in accordance with Best Practice Guide 3.
- If in doubt consult a qualified electrician. The accessory plate must be installed in accordance with the latest IET Wiring Regulations, BS7671.
- If this product is being fitted as a replacement part to an existing installation account must be taken to the version of the wiring regulations it was installed to.
Installation Information
- When removing the cables from the terminals, note the cable connections in the terminal to ensure the correct wiring of the new accessory.
- The mounting box must be of the correct size for the product, metal or plastic.
- Please see Technical Information overleaf for minimum back box depth, range dependant. The cable must be routed through the most suitable entry point of the mounting box.
- Cables should be prepared to the appropriate lengths (as stated within these instructions) so that the conductor reaches into the terminal, and the circuit protective conductor is the longest. The terminals should be tightened to their appropriate torque value. Do not over-tighten.
Gang 13A Switched and Unswitched Socket
Gang 13A Switched Socket (Twin Earth, Clean Earth)
CPCLNFunctional ‘clean earth’ should be connected to the terminal marked The
circuit protective conductor and any metal box earth bonding should be
connected to the terminal marked .
Gang 13A Switched and Unswitched Socket2
Gang 13A Switched Socket with Outboard Rockers2
Errors & Omissions excluded. Instructions are subject to change without notice.
Scolmore House | Mariner | Lichfield Road Industrial Estate | Tamworth |
Staffordshire | B79 7UL | United Kingdom
T: +44 (0)1827 63454 | F: +44 (0)1827 63362 | E:
technical@scolmore.com |
www.scolmore.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>