Inateck PRO8 Barcode Scanner User Guide
- June 17, 2024
- inateck
Table of Contents
- Inateck PRO8 Barcode Scanner
- Product Diagram
- Connection
- Interface Instructions
- Control Center
- Scanning Interface
- Scanning Modes
- Settings
- Collector
- Battery Pop-up Reminder
- Product Specification
- Package List
- FCC Note
- Service Center
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Inateck PRO8 Barcode Scanner
Product Diagram
Buttons on the Base
Scan Mode Switch : When the scanner is paired with the base, place it
into the base and press the button to switch between Manual Scan and Hands-
free Scan.
Connection Mode Switch : Long press the button for 3s to switch .
This is a brief version of PB instruction manual. For more detailed function
illustrations, please contact us. We will try our best to solve your problem
in time.
Connection
*() Wireless Adapter Mode**
Wireless Adapter Mode is the default connection mode of Pro 8 barcode scanner.
Bluetooth Mode
To enter this mode, please go to Settings- Wireless Setting-Choose the mode
you need (Bluetooth HID/SPP/GATT)-Click “Paring”.
Interface Instructions
You can swipe left or right on the screen to switch interfaces between Scanning Interface, Scanning Modes, Settings, and Collector.
Click the required function in the interface to confirm or enter the next menu.
In sub-interfaces, sliding inward from the left or right edges of the screen will return to the previous menu.
( Note: For the Prefix and Suffix Settings, you need to press the on the screen to return to the previous menu.
Control Center
Swipe down on any interface to access.
Scanning Interface
Scanning Modes
Scroll up and down to switch scanning modes.
This scanner supports three scanning modes, Manual mode, Continuous Mode, and
Hands-free Mode. The manual scanning is the default mode.
Settings
On this interface, you can configure basic settings, such as Wireless Settings, Scan Settings, Timestamp, Factory Reset, etc. You can also view parameter information for this device, including name, software version and battery level.
Collector
On this interface, you can collect barcodes and then upload them in batches. This interface includes Start Collection, Barcode Upload, Duplicate Scan Check, etc.
Battery Pop-up Reminder
-
When the battery level is under 30%, a “Low Battery” pop-up reminder will appear on the screen. Please recharge the scanner in time. You can connect the included USB cable to the charger or the USB port of a computer, or you can place the scanner on the base to charge the scanner.
-
When the battery power runs out, a “Power OFF” pop-up reminder will appear on the screen. Do not try to turn it on again, and recharge the scanner in time.
(Note: The battery level display mainly depends on the battery voltage. The
battery’! :voltage will fluctuate when the scanner is used, and the power
level will fluctuate: !_accordingly. Please refer to the pop-up reminder for
low power.
Product Specification
Package List
- Pro 8*1
- USB Cable*l
- Instruction Manual*1
FCC Note
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the Users, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.
Note: The Grantee is not responsible for any changes or modifications not
expressly approved by the party responsible for compliance. such modifications
could void the user’s authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirements.
This equipment complies with FCC’s RF radiation exposure limits set forth for
an uncontrolled environment. This device and its antenna(s) must not be co-
located or conjunction with any other antenna or transmitter.
EU Declaration of Conformity
lnateck Co., Ltd. hereby declares that this device complies with the Directive
2014/53/ EU .
A copy of the Declaration of Conformity can be accessed from
https://www.inateck.de/pages/euro-compliance.
Service Center
Europe
F&M Technology GmbH
Tel: +49 3415199 8410 (Working day 8 AM – 4 PM CET)
Fax: +49 3415199 8413
Address: Fraunhoferstral!.e 7, 04178 Leipzig, Deutsch land
North America
lnateck Technology Inc.
Tel:+ 1 {909) 698 7018 {Working day 9 AM -5 PM PST) Address: 2078 Francis St.,
Unit 14-02, Ontario, CA 91761, USA
Manufacturer
Shenzhen lnateck Technology Co., Ltd.
Address: Suite 2507, Block 11 in Tian An Cloud Park, Bantian Street, Longgang
District, Shenzhen, Guangdong, China
EC REP
F&M Technology GmbH
FraunhoferstraBe 7, 04178 Leipzig, Deutschland
Tele +49 3415799 8410
UK REP
lnateck Technology (UK) Ltd.
95 High Street, Offlce B, Great Missenden, United Kingdom, HP16 OAL
Tele +44 20 3239 9869
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>