NIGTSTICK XPP-5454GC Intrinsically Safe Headlamp Instruction Manual

Instruction Manual
XPP-5454GC
US PATENT 9,713,217

THE XPP-5454GC IS APPROVED FOR USE
Bayco Products, Inc. XPP-5454GC 640 S. Sanden Blvd., Wylie, TX 75098

ID 5012927
INTRINSICALLY SAFE SECURITE INTRINSEQUE CLASS I DIV 1 GRPS A-D T3 CLASS II & III GRPS E-G T135ºC CLASS I ZONE 0 AEx ia IIC T3 Ga Ex ia IIC T3 Ga II 1 G Ex ia op is IIC T3 Ga

Ex ia op is IIC T3 Ga Intertek ITS 13 ATEX27928X IECEx ITS 18.0030X -20ºC ≤ Tamb ≤ +40ºC 1.5V/Cell E92 or EN92

WARNINGS – INTRINSICALLY SAFE

• Warning: Use only the approved non-rechargeable batteries listed below.
• Warning: Do NOT attempt to use rechargeable AAA batteries with this light.
• Warning: To prevent ignition of a hazardous atmosphere, do not open the battery compartment in the hazardous nvironment. This task must ONLY be performed in an area known to be non-hazardous.
• Warning: When exchanging batteries, use only ENERGIZER E92 or EN92 BATTERIES.
•  Warning: To prevent ignition of a hazardous atmosphere, the AAA batteries must only be exchanged in an area known to e  on-hazardous.
•  Warning: To reduce the risk of explosion, do not mix new non-rechargeable batteries with used non-rechargeable batteries,  r mix non-rechargeable batteries from different manufacturers.
•  Warning: Substitution of components may impair intrinsic safety.

SPECIAL INSTRUCTIONS FOR INTRINSIC SAFETY

•  For personal safety, always confirm the rating of any known hazardous or potentially hazardous location where the light is to be used.

BATTERY INSTALLATION
WARNING: In order to maintain the XPP-5454’s Intrinsically Safe rating, the only AAA batteries certified for use with this ight are the ENERGIZER E92 or EN92 BATTERIES.

• Do not attempt to use any other brand or model of AAA batteries with this light.

• Do not attempt to use any type of rechargeable AAA batteries with this light.
  Warning: To prevent ignition of a hazardous atmosphere, do not open the battery compartment door in the hazardous nvironment. This task must ONLY be done in an area known to be non-hazardous.

• Loosen the locking screw located on the back of the battery compartment door. NOTE: Do NOT attempt to completely remove the locking screw. Doing so is not necessary and may damage the threads. The screw simply needs to be loosened enough to allow the battery compartment door to open.

• Using 3 – AAA ENERGIZER E92 or EN92 BATTERIES (make sure that all 3 batteries are of the same model), install the batteries in the back of the light paying close attention to the markings inside the battery compartment for proper battery
  terminal polarity alignment.

•  Close the battery compartment door.

• Tighten locking screw. CAUTION: Do NOT over-tighten. Doing so may damage the threads and impact the light’s Intrinsic Safety.

OPERATION

THE XPP-5454GC HAS TWO BUTTONS THAT CONTROL LIGHT OUTPUT:

LIGHTING MODES

Pressing the Spotlight Button will turn on the spotlight. Pressing the Floodlight Button will turn on the floodlight. Pressing both uttons will turn on both the Spotlight and the Floodlight. This mode is called Dual-Light.

EACH BUTTON HAS TWO BRIGHTNESS SETTINGS

• High-brightness – Press the desired button once
• Low-brightness – Press the desired button a second time
• Pressing the same button a third time will turn that lighting mode off

THE XPP-5454GC HAS A TILT ADJUSTMENT FEATURE:
Simply adjust the tilt angle of the light to illuminate the desired area.

THE XPP-5454GC FITS ON ANY HARD HAT THAT HAS A HARD HAT LAMP BRACKET ATTACHED:
NIGHTSTICK NS-HMC4 HEADLAMP BRACKET MOUNTING INSTRUCTIONS

• Ensure mounting surface is clean and oil-free (use alcohol wipe if needed)
• Prior to installing, determine the mounting location that allows the headlamp to fully tilt without interfering with the helmet brim.
• Remove adhesive backing.
• Firmly press bracket into place up for 30 seconds with the flat side facing up (see image).
• While supporting mount, slide headlamp clip into bracket slot. (Note: adhesive reaches peak strength in 24 hours)

TO ATTACH TO THE HARD HAT LAMP BRACKET
Slide the clip on the back of the XPP-5454GC into the slot on the top edge of the Hard Hat Lamp Bracket and press down firmly until the clip is fully engaged into the bracket.
TO REMOVE FROM THE HARD HAT LAMP BRACKET
Grasp the XPP-5454GC and pull up until the clip slides out of the Hard Hat Lamp Bracket.

WARRANTY
LIMITED LIFETIME WARRANTY
Bayco Products, Inc. warrants this product to be free from defects in workmanship and materials for the original purchaser’s lifetime. The Limited Lifetime Warranty includes LEDs, housing, and lenses. Rechargeable batteries, chargers, switches, electronics, and included accessories are warranted for a period of two years with proof of purchase. Normal wear and failures which are caused by accidents, misuse, abuse, faulty installation, and lightning damage are excluded. We will repair or replace this product should we determine it to be defective. This is the only warranty, expressed or implied, including any warranty of merchantability or fitness for a particular purpose. For a complete copy of the warranty, go to www.nightstick.com/nightstick-product- support/warranties. Retain your receipt for proof of purchase.

**** Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.nightstick.com INS-XPP-5454GC-LG-21

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>