regalo 1163WS Extension Platinum User Guide
- June 17, 2024
- regalo
Table of Contents
Wall Safe® Safety Gate
Model : 1163WS, 1168WS
• READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE.
KEEP INSTRUCTIONS FOR FUTURE USE.
Before Assembly
PLEASE CHECK TO MAKE SURE YOU HAVE THE FOLLOWING PARTS:
(A) 4″ Extension (1)
(B) Gate Frame (1)
(C) 4″ Extension (1)
(D) Wall Shields™ (4)
(E) 1″ Wall Mount Screws (4)
(F) Threaded Spindle Rods (4)
BEFORE
USING PRODUCT
Read and follow all instructions carefully to ensure that your gate and
extensions are properly installed. Improper installation could result in the
gate becoming unstable or dislodged from the doorway. Always make sure the
extension is securely attached to the gate before using. The safety of your
child is your responsibility. Please keep these instructions for your
reference.
IMPORTANT
- Never use more than two extensions per side of gate.
- If hardware mounting to a surface other than drywall or wood, please consult with a professional about installation.
- Base locks are to be used at all times, on both sides of the gate.
REMOVING YOUR GATE FROM THE WALL
To remove your gate from the wall, rotate the adjustment wheels on each of the
(4) threaded spindle rods to depressurize the gate from its doorway or
opening. Then, gently pull or push the gate free from its doorway or opening.
CARE AND MAINTENANCE
Periodically check the gate for signs of damage, wear, or missing components.
Do not use if any part is missing, worn or damaged. Check the gate regularly
to ensure all the hardware and mountings are tightened. Do not use abrasive
cleaners or bleach. Clean by sponging with warm water and a mild detergent.
Assembling and Installing Your Gate
Locate the (4) threaded spindle rods (F) Rotate the adjustment wheels along the threading, eliminating the gap between the adjustment wheel and the rubber foot.
Insert the (4) threaded spindle rods into the holes at each of the four
corners of the gate.
NOTE: You will notice a slight gap between the gate door latch and the
frame. This is not a defect. Your gate is a pressure mounted gate and this gap
will disappear once you tighten your gate in its opening.
Position the gate (B) so that it is level and centered within your doorway or
opening. Rotate the adjustment wheels on the threaded spindle rods in the
opposite direction as in Step 1, expanding the gap between the rubber foot and
the adjustment wheel. Expand each of the (4) threaded spindle rods until they
make contact with the doorway or opening. Do not fully tighten the threaded
spindle rods yet.
NOTE: The gap between the gate and wall should not exceed more than 2.5
inches. Make the appropriate adjustment to ensure you have installed your gate
safely.
When you are satisfied with the general placement of your gate, fully tighten the threaded spindle rods attached to the lower corners of the gate by further rotating the adjustment wheels. Continue by tightening the upper threaded spindle rods. As you tighten the threaded spindle rods, you will notice the gap between the door frame and the secure slide latch begin to narrow. In order for the gate to function properly, stop tightening the upper threaded spindle rods just before the outer housing of the secure slide latch and the receiving component touch.
When you are satisfied with the general placement of your gate, fully tighten
the threaded spindle rods attached to the lower corners of the gate by further
rotating the adjustment wheels. Continue by tightening the upper threaded
spindle rods. As you tighten the threaded spindle rods, you will notice the
gap between the door frame and the secure slide latch begin to narrow. In
order for the gate to function properly, stop tightening the upper threaded
spindle rods just before the outer housing of the secure slide latch and the
receiving component touch.
NOTE: There should be equal spacing among each of the (4) threaded
spindle rods. Make the appropriate adjustment to ensure you have installed
your gate safely.
Operating the Door Latch
Push one or both of the circular buttons on the secure slide latch while
simultaneously pulling back. These two actions combined will disengage the
lock and allow the gate to open freely.
Push or pull to open the gate door. To close, simply push or pull the door
back into its original position. The secure slide latch will re-engage
automatically and lock the door into its closed position.
NOTE: If your secure slide latch is not properly engaging with the
receiving component, ensure that your gate is level, mounted properly, and
that you have not over-tightened the threaded spindle rods.
At the bottom of the gate door, rotate the base lock to the horizontal
position.
To allow the door to swing open in only one direction rotate the base lock on
one side. To allow the door to swing open in both directions, rotate the base
lock on both sides.
NOTE: Place lock down on side occupied by the child.
Positioning and Attaching Wall Shields™
After you have mounted your gate, and you are satisfied with its positioning,
draw a circle on the surface of your doorway or opening around the perimeter
of the (4) rubber feet.
Next, completely remove the gate from the opening by loosening each of the (4)
threaded spindle rods to depressurize the gate.
With gate fully removed, you can now use the circles you marked during Step 1 as guides for screwing in your (4) wall shields™ (D). Center each of the wall shields™ within the guide circles and use the provided self-tapping screws (E) to fasten them in place via the hole through the center of each wall shield™.
Reinstall your gate in the doorway or opening according to the instructions, using the newly installed wall cups as anchoring points for the (4) threaded spindle rods.
Adding a Gate Extension
Remove the top and bottom threaded spindle rods.
Assemble the gate and extension as illustrated.
Reposition the gate and fit in accordance with the gate fitting.
NOTE: It is preferable to install any extensions on the hinge side of the
gate.
Replacement Parts
A Hardware Box #14057 Includes:
Threaded Spindle Rods w/ Adjustment Wheel (4), 1” Wall Mount Screws (4), Wall
Shields™ (4)
90 DAYS LIMITED WARRANTY
If, during the first 90 days after consumer purchase of the item, under
reasonable and non-commercial use and conditions of maintenance, it fails
while owned by the original purchaser because of the quality of materials or
workmanship of finish and assembly, Regalo International, LLC, will replace or
repair it at Regalo’s option.
PROOF OF PURCHASE REQUIRED.
Need more width? Additional extensions sold separately
www.regalo-baby.com
WARNING
The gap between the gate and wall should not exceed more than 2.5 inches.
NOTE: When installing any gate at its maximum width, use wall cups to ensure stability and safety.
- Install according to manufacturer’s instructions.
- To prevent serious injury or death, securely install gate or enclosure and use according to manufacturer’s instructions.
- Children have died or been seriously injured when gates are not securely installed. ALWAYS install and use as directed using all required parts.
- Never stack gates on top of each other to form a taller barrier. This could result in serious injury or death.
- STOP using when a child can climb over or dislodge the gate.
- Use only with the locking mechanism securely engaged.
- To prevent falls, NEVER use at top of stairs.
- NEVER use to keep child away from pool.
- MODEL NO. 1163WS: Intended for use with children from 6 months through 24 months.
- MODEL NO. 1168WS: Intended for use with children from 6 months through 36 months.
- Always ensure the gate is resting against the floor before beginning installation.
- This product will not necessarily prevent all accidents. Never leave child unattended.
- Check the gate regularly to see if all the hardware and mountings are tightened.
- Do not use if any component is missing or damaged. • Adult assembly required.
www.regalo-baby.com
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100 / Burnsville, MN 55306, USA / , É.-U. /
, EE. UU.
866.272.5274 (U.S. only ) or / ou / o 952.435.1080
Made in China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>