SUPERATV IN-CRS-P-RAN1K-001 Ranger XP 570 Outfitter Roof Rack Instruction Manual
- June 17, 2024
- SUPERATV
Table of Contents
SUPERATV IN-CRS-P-RAN1K-001 Ranger XP 570 Outfitter Roof Rack
kit contents continue
- Do not discard packaging until product has been successfully installed.
-
Cover x 4
-
Front Bracket x 2
-
Rear Bracket x 2
Unless noted, hardware should be snug when installing components; not tight.
Liability Statement
SuperATV’s® products are designed to best fit user’s ATV/UTV under stock
conditions. Adding, modifying, or fabricating any factory or aftermarket parts
will void any warranty provided by SuperATV® and is not recommended.
SuperATV’s® products could interfere with other aftermarket accessories. If
user has aftermarket products on machine, contact\ SuperATV® to verify that
they will work together.
Although SuperATV® has thousands of satisfied customers, user should be aware
that installing lift kits, long travel, or suspension kits, tires, etc. will
change the ride of machine and may increase maintenance and part wear.
Operating any off-road machine while, or after, consuming alcohol and/or drugs
increases risk of bodily harm or death. No warranty or representation is made
as to this product’s ability to protect user from severe injury or death.
SuperATV® urges operators and occupants to wear a helmet and appropriate
riding gear at all times.
By purchasing and installing SuperATV® products, user agrees that should
damages occur, SuperATV® will not be held responsible for loss of time, use,
labor fees, replacement parts, or freight charges. SuperATV®, nor any 3rd
party, will not be held responsible for any direct, indirect, incidental,
special, or consequential damages that result from any product purchased from
SuperATV®. The total liability of seller to user for all damages, losses, and
causes of action, if any, shall not exceed the total purchase price paid for
the product that gave rise to the claim.
SuperATV® will warranty only parts provided by SuperATV®. Any damage or
problems with OEM housings, bearings, seals, or other manufacturers’ products
will not be covered
by SuperATV®.
SuperATV® parts and products are not warrantied if item was not installed
properly, misused, or modified.
Installing, adding, modifying, or fabricating any factory or aftermarket
product to your ATV/UTV may violate certain local, state, and federal laws. Be
advised that laws vary depending on town, city, county, state, etc. Use of
certain products on public streets, roads, or highways may be in violation
law. The Buyer is solely and exclusively legally and personally responsible
for any violation of the law by the installation or use of the product. You
must abide by all local, state, and federal laws, including but not limited to
vehicle safety, traffic laws, and ordinances. It is your responsibility to
know the laws and how they apply to you.
The Buyer is responsible to fully understand the capability and limitations of
his/her vehicle according to manufacturer specifications, warnings and
instructions and agrees to hold SuperATV® harmless from any damage resulting
from failure to adhere to such specifications, warnings and/ or instructions.
The Buyer is also responsible to obey all applicable federal, state, and local
laws and ordinances when operating his/her vehicle while using this product,
and the Buyer agrees to hold SuperATV® harmless from any violation thereof.
INSTALLATION INSTRUCTIONS
-
Install Passenger Kicker, along with Front and Rear Brackets, to Passenger Panel with hardware shown; do not tighten.
-
Install Rails to Passenger Panel with hardware shown; tighten.
-
Install Driver Kicker, along with Front and Rear Brackets, to Driver Panel with hardware shown; do not tighten.
-
Secure Passenger Panel to Rails with hardware shown; tighten.
-
Install Front Panel with hardware shown; do not tighten.
-
Install Rear Panel with hardware shown; do not tighten.
-
Install Covers to Panels with hardware shown; tighten.
-
Remove SuperATV Roof hardware shown.
-
Replace Short Spacers with Spacers included wih Roof Rack.
-
Place assembly onto machine.
-
Secure front section with hardware shown; do not tighten.
-
Secure rear section with SuperATV Roof hardware shown; do not tighten.
-
– Secure rear section with SuperATV Roof hardware shown; do not tighten.
-
Align assembly to machine and tighten all hardware.
Customer Support
Need help with your installation?
Read instructions and view illustrations before beginning.
sales@superatv.com
1-855-743-3427
www.superatv.com
8:00am – 8:00pm EST M-Th
8:00am – 7:00pm EST Friday
9:00am – 2:00pm EST Saturday
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>