70110015-A 4 in 1 Universal ZigBee LED Controller Instruction Manual

4 in 1 Universal ZigBee LED Controller

Important: Read All Instructions Prior to Installation

Function introduction

1. Under RGBW mode, W channel can be turned on through Gateway’s color temperature control interface which will mix RGB channels as 1 channel white and then make color tuning with the 4th channel white. Once turned on, the brightness of white channel will be controlled together with RGB channels.
2. Under RGBW mode, W channel can be controlled separately from RGB channels through RGBW zigbee remote or touch panel’s W button, please refer to their manuals.
3. Under RGB+CCT mode, RGB channels and tunable white channels are controlled separately, they can not be turned on and controlled at the same time.

Product Data

Input Voltage| Output Current| Output Power| Remarks| Size(LxWxH)| Ambient Temperature| Max. Casing Temperature
---|---|---|---|---|---|---
12-24VDC| 4A/CH| 48-96W/CH| Constant voltage| 145×46.5x16mm| -20°C ∼ +50°C| 75°C

• 4 in 1 universal Zigbee LED controller based on latest ZigBee 3.0 protocol
• 4 different device modes DIM, CCT, RGBW and RGB+CCT in 1 controller, and selectable by dial switch
• Enables to control ON/OFF, light intensity, color temperature, RGB color of connected LED lights
• Can directly pair to a compatible ZigBee remote via Touchlink
• Supports self-forming zigbee network without coordinator
• Supports find and bind mode to bind a ZigBee remote
• Supports zigbee green power and can bind max. 20 zigbee green power remotes
• Compatible with universal Zigbee gateway or hub products
• Compatible with universal Zigbee remotes
• Waterproof grade: IP20

Safety & Warnings

• DO NOT install with power applied to device.
• DO NOT operate the dial switches for device mode selection with power applied to device.
• DO NOT expose the device to moisture.

Operation

1. Do wiring according to connection diagram correctly, please power off and power on the device once a device mode is selected so that the selected mode can be activated.

2. This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee system.

3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)
   Step 1: Remove the device from previous zigbee network if it has already been added to, otherwise pairing will fail. Please refer to the part “Factory Reset Manually”.
   Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as instructed by the controller.
   Step 3: power on the device, it will be set into network pairing mode (connected light flashes twice slowly), the network pairing mode will last until the device is added to a zigbee network.

4. TouchLink to a Zigbee Remote
   Step 1: Method 1: Short press “Prog” button 4 times (or reset power of the device 4 times) to start Touchlink commissioning immediately under any circumstances, which lasts for 180S, once time out, repeat this step.
   Method 2: Add the device to a Zigbee network, then it will be set into Touchlink commissioning immediately, Touchlink will last for 180S, once time out, reset power of the device to set it into touchlink commissioning again. Note: 1) Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote.

2. TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes.
3. To control by both hub and remote, add remote and device to hub network first then TouchLink.
4. After TouchLink, the device can be controlled by the linked remotes.

5. Removed from a Zigbee Network through Coordinator or Hub Interface

6. Factory Reset Manually
   Step 1: Short press “Prog.” key for 5 times continuously or reset power of the device for 5 times continuously if the “Prog.” key is not accessible. Note: All configuration parameters will be reset after the device is reset or removed from the network.

7. Factory Reset through a Zigbee Remote (Touch Reset)
   Step 1: Reset power of the device to start TouchLink Commissioning, 180 seconds timeout, repeat this step. Note: Make sure the device already added to a network, the remote added to the same one or not added to any network.

8. Find and Bind Mode
   Step 1: Short press “Prog.” button 3 times (Or reset power of the device (initiator node) 3 times) to start Find and Bind mode (connected light flashes slowly) to find and bind target node, 180 seconds timeout, repeat the step. Note: Make sure the device and the remote or touch panel already added to the same Zigbee hub.

9. Learning to a Zigbee Green Power Switch
   Step 1: Short press “Prog.” button 4 times (Or reset power on the device 4 times) to start Learning to GP switch mode (connected light flashes twice), 180 seconds timeout, repeat the step.

10. Delete Learning to a Zigbee Green Power Switch
    Step 1: Short press “Prog.” button 3 times (Or reset power of the device 3 times) to start delete Learning to GP switch mode (connected light flashes slowly), 180 seconds timeout, repeat the step.

11. Setup a Zigbee Network & Add Other Devices to the Network (No Coordinator Required)
    Step 1: Short press “Prog.” button 4 times (Or reset power of the device 4 times) to enable the device to setup a zigbee network (connected light flashes twice) to discover and add other devices, 180 seconds timeout, repeat the step. Step 2: Set another device or remote or touch panel into network pairing mode and pair to the network, refer to their manuals.
    Step 3: Pair more devices and remotes to the network as you would like, refer to their manuals.
    Step 4: Bind the added devices and remotes through Touchlink so that the devices can be controlled by the remotes, refer to their manuals.
    Note: 1) Each added device can link and be controlled by max. 30 added remotes.

2. Each added remote can link and control max. 30 added devices.

12. ZigBee Clusters the device supports are as follows:
    Input Clusters
    • 0x0000: Basic
    • 0x0003: Identify
    • 0x0004: Groups
    • 0x0005: Scenes
    • 0x0006: On/off
    • 0x0008: Level Control
    • 0x0300: Color Control
    • 0x0b05: Diagnostics
    Output Clusters
    • 0x0019: OTA

13. OTA
    The device supports firmware updating through OTA, and will acquire new firmware from zigbee controller or hub every 10 minutes automatically.

Product Dimension

Wiring Diagram

1. RGB+CCT Mode Note: please make sure the dial switches are at position for RGB+CCT mode as shown in above diagram.
2. RGBW Mode Note: please make sure the dial switches are at position for RGBW mode as shown in above diagram.
3. CCT Mode Note: please make sure the dial switches are at position for CCT mode as shown in above diagram.
4. DIM Mode Note: please make sure the dial switches are at position for DIM mode as shown in above diagram.

70110015-A

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>