Enbrighten 58438 In Wall Smart Dimmer User Manual

Enbrighten 58438 In Wall Smart Dimmer

Product Specifications

• Brand: Jasco Products Company
• Model: ZWA3016ENB/58438
• Maximum Load Capacity: 600W incandescent, 300W dimmable CFL/LED
• Control Method: Z-Wave enabled controller

Product Usage Instructions

Installation Tools Required

Before installing the Z-Wave in-wall smart dimmer, ensure you have the following tools:

• Screwdriver
• wire stripper
• Electrical tape

Installation Steps

1. Turn off the power to the circuit at the breaker box.
2. Remove the existing switch plate and switch from the wall.
3. Identify the wires according to the labels provided in the manual.
4. Connect the wires to the corresponding terminals on the Z-Wave dimmer as instructed.
5. Secure the dimmer in the wall and attach the faceplate.
6. Turn the power back on and test the dimmer.

Operation

• The Z-Wave in-wall smart dimmer can be controlled using a Z-Wave-enabled controller.

• Adjust settings and configurations using the controller to customize dimming levels and other features.

Frequently Asked Questions (FAQ):

Q: Can I exceed the maximum load capacity of the dimmer?

• A: No, to ensure safety and proper functionality, do not exceed the specified load capacity of 600W incandescent or 300W dimmable CFL/LED.

Q: How can I reset the dimmer to factory settings?

• A: Refer to the user manual for instructions on resetting the dimmer to its factory settings. Typically, this involves a specific sequence of actions on the dimmer itself or through the Z-Wave controller.

Q: What should I do if I encounter issues during installation?

• A: If you face challenges during installation, contact our U.S.-based Consumer Care at 1-800-654-8483 for assistance. Ensure to follow all safety precautions and consult a professional if needed.

FCC/IC

This device complies with Part 15 of the FCC and Industry Canada license- exempt RSS standards Operation is subject to the following two conditions:

1. this device may not cause harmful interference,
2. this device must accept any interference received, including interference that may cause undesired operation.

FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to protect reasonably against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Important note: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted.
Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void the user’s authority to operate the device.

*Convert any smart control to a multi-location switch**

For a list of compatible devices, visit ezzwave.com

To purchase an add-on switch or for more details, visit ezaddonswitch.com.

Multiple Paddle Colors Available ezzwave.com/paddlecolors.

Purchase additional items at EZzwave.com or visit your local retailer.

DO NOT RETURN THIS PRODUCT TO THE STORE

• Questions? Contact our U.S.-based Consumer Care at 1-800-654-8483 between 7 AM-8 PM, M-F, Central Time.
• For the most up-to-date product support, accessories, electronic (PDF) format manuals, and more, visit www.byjasco.com/support.
• No user-serviceable parts in this unit

WARNING

• RISK OF FIRE
• RISK OF ELECTRICAL SHOCK
• RISK OF BURNS
• CONTROLLING APPLIANCES
• CAUTION: TO REDUCE THE RISK OF OVERHEATING AND POSSIBLE DAMAGE TO OTHER EQUIPMENT, DO NOT INSTALL TO CONTROL A RECEPTACLE, A MOTOR-OPERATED APPLIANCE, A FLUORESCENT LIGHTING FIXTURE OR A TRANSFORMER-SUPPLIED APPLIANCE.
• ONLY USE TO CONTROL INCANDESCENT OR DIMMABLE CFL/LED BULBS
• DO NOT EXCEED RATINGS
• DO NOT USE TO CONTROL ANY DEVICE WHERE UNINTENDED OPERATION COULD CAUSE UNSAFE CONDITIONS (HEAT LAMP, SUN LAMP, ETC.)
• FOR INDOOR USE ONLY

NOT FOR USE WITH MEDICAL OR LIFE-SUPPORT EQUIPMENT

• Z-WAVE-ENABLED DEVICES SHOULD NEVER BE USED TO SUPPLY POWER TO OR CONTROL THE ON/OFF STATUS OF MEDICAL OR LIFE-SUPPORT EQUIPMENT

SPECIFICATIONS

ZWA3016ENB

• Power: 120VAC, 60Hz
• Signal (frequency): 908.4/916MHz
• Maximum loads: 1-gang 600W, 2-gang 500W or 3-gang 400W incandescent, 300W dimmable CFL/LED
• Range: Up to 150ft. line of sight between the wireless controller and the closest Z-Wave receiver module.
• Operating temperature range: 32-104° F (0-40° C)
• Type 1 enclosure, independently mounted (vertical position only), operating control: type 1. c action, pollution degree (2), impulse voltage (2500V), software class A For indoor use only
• Specifications are subject to change without notice due to continuing product improvement

Tools you will need

IMPORTANT!

• The fixture controlled by the Z-Wave in-wall smart dimmer must not exceed 600W incandescent, 300W dimmable CFL/LED.
• The dimmer is designed only for use with permanently installed fixtures

Getting to know your new Z-Wave device

• Turn ON/OFF and adjust dim levels manually or remotely via the Z-Wave controller
• Can be added in multiple groups and scenes
• May be used in single-pole installation or with up to four add-on switches (46199/59339) in 3-way or 4-way wiring configurations
• Compatible with all incandescent and most dimmable CFL/LED bulbs
• Auto line/load detection
• Interchangeable paddle — white & light almond paddle in package
• Uses a standard, rocker-style wallplate for single-gang installations (wallplate not included)
• Multicolor LED indicates dimmer location in a dark room
• Z-Wave certified for simple pairing and integrated home automation
• Screw terminal installation — requires wiring connections for line (hot), load, neutral, and ground.
• Traveler wire required for 3-way or 4-way installation
• This Z-Wave device has advanced features that allow you to customize your experience.
• These features can only be adjusted by a Z-Wave enabled controller that supports the Z-Wave configuration command class.
• For a complete list of adjustable configurations, visit www.ezzwave.com/config

INSTALLATION INSTRUCTION

• A. Ground (Green/Bare)
• B. Line or Load (Black)
• C. Line or Load (Black)
• D. Traveler (Red/Other)
• E. Neutral (White)
• F. Top rocker — press & release to turn dimmer ON, press & hold increases brightness
• G. Bottom rocker — press & release to turn dimmer OFF, press & hold to dim
• Insert wires into holes, do not wrap wires around screws.
• Do not remove screws

WARNING — SHOCK HAZARD

• Turn OFF the power to the branch circuit for the dimmer and lighting fixture at the service panel.
• All wiring connections must be made with the POWER OFF to avoid personal injury and/or damage to the dimmer.
• This device is intended for installation under the National Electric Code and local regulations in the United States or the Canadian Electrical Code and local regulations in Canada.
• If you are unsure or uncomfortable about performing this installation, consult a qualified electrician.

Multi-switch wiring

• For 3-way installations, please refer to the add-on switch (46199/59339) manual

Single-switch wiring

• Before installation, you may wish to change the paddle color to match your wallplate or décor.

Please proceed to section 5.

1. Shut off power to the circuit at the circuit breaker or fuse box.
   • IMPORTANT! Verify power is OFF to the switch box before continuing.
2. Remove wallplate.
3. Remove the switch mounting screws.
4. Carefully remove the switch from the switch box. DO NOT disconnect the wires.
5. There are up to five screw terminals on the switch; these are marked:
   • A. GROUND — Green/Bare
   • B. LINE OR LOAD — Black (connected to power or lighting)
   • C. LINE OR LOAD — Black (connected to power or lighting)
   • D. TRAVELER — Red/Other (only in 3-way installations)
   • E. NEUTRAL — White
   • Match these screw terminals to the wires connected to the existing switch.
6. Disconnect the wires from the existing switch. Label wires according to the previous terminal connection

Observe important wiring information

• IMPORTANT! This switch is rated for and intended to only be used with copper wire.

Wire gauge requirements

• Use 14AWG or larger wires suitable for at least 80° C for supplying line (hot), load, neutral, ground, and traveler connections.

Wire strip length

• For attachment using the enclosure’s holes, strip insulation 5/8in. (16mm).
• UL specifies the tightening torque for the screws as 14Kgf-cm (12lbf-in).

1. Connect the green or bare copper ground wire to the GROUND terminal.
2. Connect the black wire from the electrical service panel (hot) to either the LINE/LOAD terminal.
3. Connect the black wire from the light to the other LINE/LOAD terminal.
4. Connect the white wire to the NEUTRAL terminal (use a jumper wire if needed).
   • NOTE: The traveler terminal is only used for 3-way or 4-way wiring and should remain unused if the dimmer is being installed in a 2-way system (one switch & one load).
5. Insert the dimmer into the switch box being careful not to pinch or crush wires.
6. The dimmer must be independently mounted (vertical position only).
7. Secure the dimmer to the box using the supplied screws.
8. Mount the wallplate.
9. Reapply power to the circuit at the fuse box or circuit breaker and test the system.

Basic operation

The connected light can be turned ON/OFF and adjust dim levels in two ways:

1. Manually from the front panel of the dimmer.
2. Remotely with a Z-Wave controller.

Manual control

The front panel rocker dimmer allows the user to turn ON/OFF the connected fixture.

1. To turn the connected fixture ON, press and release the top of the rocker.
2. To turn the connected fixture OFF, press and release the bottom of the rocker

Adjust dim levels

1. To increase brightness, press and hold the top of the rocker.
2. To decrease brightness, press and hold the bottom of the rocker.

Cycle LED light

• The LED below the dimmer acts as a guide light or status indicator.
• How to cycle through options: Press up three times and down once quickly.

1. LED is ON when the load is OFF (guide light in the dark) (default)
2. LED is ON when the load is ON (indicates the dimmer is ON)
3. LED is always OFF
4. LED is always ON (illuminates dimmer in the dark)

LED bulb adjustments

• Not all LED bulbs are made the same, and performance varies between dimmer brands.
• This can cause adverse bulb behavior, such as flickering or strobing.
• To account for this scenario, this dimmer features adjustable dim and brightness thresholds to allow setting minimum and maximum levels.

Minimum dim threshold

1. Press the ON button four times, then the OFF button once quickly.
2. Light starts at the most recent dim level (default — 1%).
3. Press the top or bottom rocker button until the bulb reaches the desired brightness without flickering.
4. The LED stops flashing 10 seconds after releasing the button to indicate the minimum threshold is set.
   • NOTE: This can be set by Z-Wave configuration parameter 30/size: 1 byte/values 1-99 (default — 1)

Maximum brightness threshold

1. Press the OFF button four times, then the ON button once quickly.
2. Light starts at the most recent brightness (default — 99%)
3. Press the top or bottom rocker button until the bulb reaches the desired brightness without flickering.
4. The LED stops flashing 10 seconds after releasing the bottom to indicate the maximum threshold is set.

NOTE: This can be set by Z-Wave configuration parameter 31/size: 1 byte/values 1-99 (default — 99)

Adding your device to a Z-Wave network:

1. Follow the instructions for your Z-Wave-certified controller to add a device to the Z-Wave network.
2. Once the controller is ready to add your device, press the top or bottom of the wireless smart dimmer (rocker).

• The controller’s app will indicate if it has discovered the dimmer. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the side of the box or the QR code label on the product (see Figure 1).
• Enter the 5-digit code.
• You have complete control to turn your fixture ON/OFF/DIM and create groups, scenes, schedules, and interactive automatons programmed by your controller.
• If your Z-Wave-certified controller features remote access, you can control your fixture from your mobile devices.

To remove and reset the device:

1. Follow the instructions for your Z-Wave-certified controller to remove a device from the Z-Wave network.
2. Once the controller is ready to remove your device, press the top or bottom of the wireless smart dimmer (rocker).

• To return your switch to factory defaults: Pull the airgap switch. Press and hold the bottom button, push the airgap switch in, and continue holding the bottom button for 10 seconds.
• The LED will flash once each of the 8 colors then stop.
• NOTE: This should only be used if your network’s primary controller is missing or otherwise inoperable.
• NOTE: SmartStart-enabled products can be added to a Z-Wave network by scanning the QR code on the product with a controller providing SmartStart inclusion.
• No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on in the network vicinity.

To change the color of the paddle

This step is optional. Before installation, you may want to change the color of the paddle to match your wallplate or décor.

1. Lift the air gap tab at the base of the paddle.
2. Push side tabs in on one side and then the other to release the paddle. Lift the cover-up and off.
3. Simply put the new paddle onto the switch by inserting the air gap and side tabs and snapping it securely into place.
   • Once this step has been completed, please return to section 3.

An add-on switch (46199/59339) is required for multi-switch 3-way or 4-way installations

• Connecting the traveler terminal of this dimmer to a standard switch will cause damage or result in improper function.
• If this dimmer is part of a 3-way or 4-way multi-switch installation, do not connect the traveler wire or apply power until add-on switches are correctly installed.
• For more information on 3-way or 4-way installations, view the manual or quick-start guide with the add-on switch (46199/59339).

Z-WAVE INTEROPERABILITY

• This product can be added and operated in any Z-Wave network with other Z-Wave-certified devices from other manufacturers and/or other applications.
• All non-battery-operated nodes within the network will act as repeaters regardless of vendor to increase the reliability of the network.
• NOTE: The actual performance of any CFL or LED will vary from bulb type to bulb type and among manufacturers.
• It is important to note only bulbs designed as dimmable should be used on a dimmer.
• To find out if your bulb is dimmable, please check the package, and the bulb itself, or call the bulb manufacturer directly.
• For a complete list of recommended CFL/LED bulbs for this and other Z-Wave products from Jasco, please visit www.ezzwave.com

This device supports Association Command Class (3 Groups)

• Association Group 1 supports Lifeline, Multi-level Switch report
• Association Group 2 supports the Basic Set and is controlled with the local load
• Association Group 3 supports the Basic Set and is controlled by double pressing the ON or OFF button
• Each Association Group supports 5 total nodes

WARRANTY

• Jasco Products Company warrants this product to be free from manufacturing defects for five years from the original date of consumer purchase.
• This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product.
• This warranty is in place of all other warranties, expressed or implied.
• Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you.
• This warranty gives you specific rights, and you may also have other rights which vary from state to state.
• Please contact our U.S.-based Consumer Care at 1-800-654-8483 (option 1) between 7 AM–8 PM, M- F, Central Time, or www.byjasco.com if the unit should prove defective within the warranty period.

Z-Wave Configuration Capabilities

Z-Wave Command Class:

Note:

• BASIC SET will map to SWITCH_MULTILEVEL_SET and their value will map the same.
• Basic Report (Current Value, Duration) map to SWITCH_MULTILEVEL_REPORT (Value, Duration).
• Read instructions or watch easy-to-follow video Scan the QR code or visit https://byjasco.com/58438i

Documents / Resources

| Enbrighten 58438 In Wall Smart Dimmer [pdf] User Manual
58438 In Wall Smart Dimmer, 58438, In Wall Smart Dimmer, Wall Smart Dimmer, Smart Dimmer, Dimmer
---|---

References

• Add-On Switches
• Z-Wave by Jasco
• Add-Ons
• Jasco
• Support
• Z-Wave by Jasco
• YouTube

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>